Icom IC-F30GT Bedienungsanleitung

INSTRUCTION MANUAL

This device complies with Part 15 of the FCC

Rules. Operation is subject to the condition that

this device does not cause harmful interference.

UHF TRANSCEIVER

iF40GT/GS

iF30GT/GS

VHF TRANSCEIVER

IC-F30G series-5.qxd 05.2.21 14:34 Page i (1,1)

Your Icom radio generates RF electromagnetic en-

ergy during transmit mode. This radio is designed

for and classified as “Occupational Use Only”,

meaning it must be used only during the course of

employment by individuals aware of the hazards,

and the ways to minimize such hazards. This radio

is NOT intended for use by the “General Popula-

tion” in an uncontrolled environment.

This radio has been tested and complies with the FCC RF expo-

sure limits for “Occupational Use Only.” In addition, your Icom radio

complies with the following Standards and Guidelines with regard to

RF energy and electromagnetic energy levels and evaluation of

such levels for exposure to humans:

• FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating

Compliance with FCC Guidelines for Human Exposure to Radio

Frequency Electromagnetic Fields.

• American National Standards Institute (C95.1–1992), IEEE Stan-

dard for Safety Levels with Respect to Human Exposure to Radio

Frequency Electromagnetic Fields, 3 kHz to 300 GHz.

• American National Standards Institute (C95.3–1992), IEEE Rec-

ommended Practice for the Measurement of Potentially Hazardous

Electromagnetic Fields— RF and Microwave.

To ensure that your exposure to RF electromag-

netic energy is within the FCC allowable limits for

occupational use, always adhere to the following

guidelines:

•DO NOT operate the radio without a proper antenna attached, as

this may damage the radio and may also cause you to exceed FCC

RF exposure limits. A proper antenna is the antenna supplied with

WARNING

CAUTION

SAFETY TRAINING INFORMATION

IC-F30G series-5.qxd 05.2.21 14:34 Page ii (1,1)

this radio by the manufacturer or an antenna speciﬁcally authorized

by the manufacturer for use with this radio.

•DO NOT transmit for more than 50% of total radio use time (

“

50%

duty cycle”). Transmitting more than 50% of the time can cause

FCC RF exposure compliance requirements to be exceeded. The

radio is transmitting when the “TX indicator” lights red. You can

cause the radio to transmit by pressing the “PTT” switch.

•ALWAYS use Icom authorized accessories (antennas, batteries,

belt clips, speaker/mics, etc). Use of unauthorized accessories can

cause the FCC RF exposure compliance requirements to be ex-

ceeded.

•ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the

body when transmitting and only use the Icom belt-clips which

listed in page 25 when attaching the radio to your belt, etc., to en-

sure FCC RF exposure compliance requirements are not ex-

ceeded. To provide the recipients of your transmission the best

sound quality, hold the antenna at least 5 cm (2 inches) from

mouth, and slightly off to one side.

The information listed above provides the user with the information

needed to make him or her aware of RF exposure, and what to do

to assure that this radio operates within the FCC RF exposure lim-

its of this radio.

Electromagnetic Interference/Compatibility

During transmissions, your Icom radio generates RF energy that

can possibly cause interference with other devices or systems. To

avoid such interference, turn off the radio in areas where signs are

posted to do so. DO NOT operate the transmitter in areas that are

sensitive to electromagnetic radiation such as hospitals, aircraft,

and blasting sites.

IC-F30G series-5.qxd 05.2.21 14:34 Page iii (1,1)

iii

FOREWORD

Thank you for purchasing the IC-F30GT/GS, IC-F40GT/GS FM

transceiver.

READ ALL INSTRUCTIONS carefully and completely before using

the transceiver.

SAVE THIS INSTRUCTION MANUAL–This instruction manual

contains important operating instructions for the transceiver.

INSTALLATION NOTES

• When transmitting with a portable radio, hold the radio in a vertical

position with its microphone 2.5 to 5 centimeters (1 to 2 in.) away

from your mouth. Keep the antenna at least 2.5 centimeters (1 in.)

from your head and body.

• If you wear a portable two-way radio on your body, ensure that the

antenna is at least 2.5 centimeters (1 in.) from your body when

transmitting.

IMPORTANT

RCAUTION! NEVER hold the transceiver so that the antenna is

very close to, or touching exposed parts of the body, especially the

face or eyes, while transmitting. The transceiver will perform best if

the microphone is 2 to 4 in. (5 to 10 cm) away from the lips and the

transceiver is vertical.

RCAUTION! NEVER operate the transceiver with a headset or

other audio accessories at high volume levels.

RCAUTION! NEVER short the terminals of the battery pack.

DO NOT push the PTT when not actually desiring to transmit.

IC-F30G series-5.qxd 05.2.21 14:34 Page iv (1,1)

AVOID using or placing the transceiver in direct sunlight or in areas

with temperatures below +14°F (–10°C) or above +122°F (+50°C).

The basic operations, transmission and reception of the transceiver,

are guaranteed within the specified operating temperature range

(depending on version). However, the LCD display may not be op-

erate correctly, or show an indication in the case of long hours of

operation, or after being placed in extremely cold areas.

DO NOT modify the transceiver for any reason.

KEEP the transceiver from the heavy rain, and Never immerse it in

the water. The transceiver construction is water resistant, not wa-

terproof.

The use of non-Icom battery packs/chargers may impair transceiver

performance and invalidate the warranty.

Versions of the IC-F30GT/GS and IC-F40GT/GS

which display the “FM APPROVED” symbol as

at left on the serial number seal, conform to in-

trinsically safe ratings of the FMRC (Factory Mu-

tual Research Corporation).

Intrinsically safe : Class I, II, III, Division 1,

Groups C, D, E, F, G

Nonincendive : Class I, Division 2, Groups A, B, C, D

Connected battery pack : BP-210N-FM, BP-210FM

FCC caution: Changes or modiﬁcations to this transceiver, not

expressly approved by Icom Inc., could void your authority to op-

erate this transceiver under FCC regulations.

IC-F30G series-5.qxd 05.3.15 1:06 PM Page v (1,1)

TABLE OF CONTENTS

SAFETY TRAINING INFORMATION ………………………………… i–ii

FOREWORD ……………………………………………………………… iii

INSTALLATION NOTES ………………………………………………… iii

IMPORTANT …………………………………………………………… iii–iv

TABLE OF CONTENTS ………………………………………………… v

1 ACCESSORIES ………………………………………………………… 1

2 PANEL DESCRIPTION …………………………………………… 2–4

‘Switches, controls, keys and connectors ……………………… 2–3

‘Function display ……………………………………………………… 4

3 BATTERY PACKS ………………………………………………… 5–10

‘Battery pack replacement…………………………………………… 5

‘Battery cautions ……………………………………………………… 6

‘Battery charging…………………………………………………… 7–8

‘ Charging NOTE ……………………………………………………… 9

‘ Battery case (Option) ……………………………………………… 10

4 PROGRAMMABLE FUNCTIONS ……………………………… 11–15

‘General ……………………………………………………………… 11

5 CONVENTIONAL OPERATION ………………………………… 16–18

‘Receiving and transmitting………………………………………… 16

‘Call procedure ……………………………………………………… 17

‘Tx code channel selection ………………………………………… 18

‘Manual 5-tone codes ……………………………………………… 18

‘Transmitting notes ………………………………………………… 18

6 SmarTrunk IITM OPERATION …………………………………… 19–21

‘Basic operation …………………………………………………… 19

7 OTHER FUNCTIONS ………………………………………………… 22

‘DTMF pager/Code squelch ……………………………………… 22

‘ Cloning ……………………………………………………………… 22

8 OPTIONAL UNIT INSTALLATION ………………………………… 23

‘ Installation…………………………………………………………… 23

9 OPTIONS ………………………………………………………… 24–25

IC-F30G series-5.qxd 05.2.21 14:34 Page vi (1,1)

ACCESSORIES

‘‘Accessory attachment

DSupplied accessories

The transceiver comes supplied with the following accessories.

qFlexible antenna

(may

differ from that shown, or

may not be supplied with

some versions)

wBelt clip (w/screws)

DAntenna

The antenna screws onto the transceiver

as illustrated at right.

✔For IC-F30GT-L/GS-L

The most suitable flexible antenna

must be purchased separately, ac-

cording to the frequency coverage and

programmed frequency parameters of

each version. See page 25 for details.

DBelt clip

Attach the belt clip to the transceiver as illustrated below.

Use the supplied screws only.

IC-F30G series-5.qxd 05.2.21 14:35 Page 1 (1,1)

PANEL DESCRIPTION

‘‘Switches, controls, keys and connectors

DDProgrammable key reference

Microphone

Speaker

F0 (Red)

F1 (Black)

F2 (Black)

F3 (Black)

IC-F30G series-5.qxd 05.2.21 14:35 Page 2 (1,1)

PANEL DESCRIPTION

qANTENNA CONNECTOR

Connects the supplied antenna.

wDEALER-PROGRAMMABLE KEY [F0 (Red)]

eDEALER-PROGRAMMABLE KEY [F1 (Black)]

rPTT SWITCH [PTT]

Push and hold to transmit; release to receive.

tDEALER-PROGRAMMABLE KEYS [F2 (Black)], [F3 (Black)]

• Push to select the operating channel. Depends on setting.

• Can be programmed as [ ✱]/[ # ]. (SmarTrunk mode only)

yDEALER-PROGRAMMABLE KEYS [P0]/[P1]/[P2]/[P3]

Can each be programmed for one of several functions by your

Icom Dealer.

u10-KEY PAD (IC-F30GT/IC-F40GT only)

Used to enter DTMF codes, the operating channel, etc.

iFUNCTION DISPLAY

Displays a variety of information such as, operating channel

number/names, 5-tone code, remaining battery power, DTMF

numbers, transmit output power setting, Audible indication, etc.

NOTE: The above functions depend on pre-setting.

oMULTI CONNECTOR

Connect optional speaker-microphone, etc.

!0 TRANSMIT/BUSY INDICATOR

Lights red while transmitting; lights green while receiving a sig-

nal, or when the squelch is open.

!1 VOLUME CONTROL [VOL]

Turns power ON and adjusts the audio level.

!2 ROTARY SELECTOR [SEL]

Selects operating channel or bank. Depends on setting.

IC-F30G series-5.qxd 05.2.21 14:35 Page 3 (1,1)

PANEL DESCRIPTION

‘‘Function display

qSIGNAL STRENGTH METER

Indicates relative signal strength level.

wBANK NUMBER INDICATOR

Indicates operating bank (channel group) number.

eLOW POWER INDICATOR

Appears when low output power is selected.

rMULTI-FUNCTION INDICATOR

Indicates operating channel number, channel names, 5-tone

code, etc., according to operating condition.

tSCRAMBLER INDICATOR

Appears while the voice scrambler function is activated.

yKEY LOCK INDICATOR

Appears during key lock function ON.

uBELL INDICATION

Appears or blinks when a 2/5Tone call is received.

iAUDIBLE INDICATOR

Appears when the monitor function is turned ON. (CTCSS and

DTCS mutes are released.)

oBATTERY INDICATOR

Indicates remaining battery power.

IC-F30G series-5.qxd 05.2.21 14:35 Page 4 (1,1)

Andere Handbücher für IC-F30GT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icom Transceiver Handbücher

Icom

Icom IC-F40GT Bedienungsanleitung

Icom

Icom IC-7851 Bedienungsanleitung

Icom

Icom IC-7200 Service-Handbuch

Icom

Icom IC-F3262DT Bedienungsanleitung

Icom

Icom IC-410PRO Installationsanleitung

Icom

Icom IC-80AD Bedienungsanleitung

Icom

Icom IC-T2H Bedienungsanleitung

Icom

Icom IC-201 Bedienungsanleitung

Icom

Icom IC-T22A Bedienungsanleitung

Icom

Icom IC-A25N Bedienungsanleitung

Icom

Icom ID-800H Bedienungsanleitung

Icom

Icom IC-718 Bedienungsanleitung

Icom

Icom IC-F29DR3 Installationsanleitung

Icom

Icom IC-M803 Bedienungsanleitung

Icom

Icom iM506 Bedienungsanleitung

Icom

Icom IC-25A Bedienungsanleitung

Icom

Icom IC-F510 Bedienungsanleitung

Icom

Icom IC-F29SR2 Bedienungsanleitung

Icom

Icom IC-820H Bedienungsanleitung

Icom

Icom IC-M423 Bedienungsanleitung

Icom

Icom IC-7410 Bedienungsanleitung

Icom

Icom IC-M506GE Bedienungsanleitung

Icom

Icom IC-775DSP Bedienungsanleitung

Icom

Icom VHF IC-F50 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung