ICP DAS USA 7188EN Installationsanleitung

分類/Classification

tDS

tGW

PETL/tET/tPET

DS/PDS/PPDS

tM-752N

I/O Card

VXC Card

VxComm

7188EN

作者/Author

Tammy

日期/Date

2016-01-12

編號/NO.

FAQ-043

Q: How to enable web server for the PDS/7188EN series module?

A: The PDS/7188EN series module contains a built-in web server that allows the settings for the module to

be remotely modified via a web interface. When the web server has been disabled (Web Server = 0), refer

to the following two methods to enable the web server.

Method 1: Enable web server on PDS by using “console port and command”.Follow the procedure

described below:

1. Power off the PDS module.

2. Connect the download-cable (CA0910), between the PDS and COM4 of the development PC.

3. Wire the CA-0910 to PDS, as follows:

Connect the CA-0910.TX with PDS.TxD

Connect the CA-0910.RX with PDS.RxD

Connect the CA-0910.GND with PDS.GND

4. Set the “Init/Normal Switch”on the PDS module to the in “Init”position.

(Or connect the INIT* pin to the GND pin.)

5. Power on the PDS module.

6. Unzip the “7188XW_yyyymmdd.zip” file on the PC. The “7188XW_yyyymmdd.zip”can be obtained

from the ICP DAS web site (http://ftp.icpdas.com/pub/cd/8000cd/napdos/minios7/utility/).

7. Open “Notepad”text editor for Windows and type the command: C4 B115200 P0D8 S1, and then save

the file as “7188xw.ini”in the same directory of 7188XW.exe.

8. Execute “7188XW.EXE”and press [Enter] key.

9. Settings configuration command:

The following is an example of a HTTP configuration.

Command

Description

HTTP= 1

Enables the Web Server.

HTTP= 0

Disables the Web Server.

Enable Web Server

C: COM Port of the development PC (e.g., C4)

B: Baud Rate (e.g., B115200)

P: Parity None (e.g., P0)

D: Data Bits (e.g., D8)

S: Stop Bits (e.g., S1)

Method 2: Enable web server on PDS by using “TCP port 10000”.Follow the procedure described below:

1. Ensure that the network settings on the Host PC have been correctly configured and are functioning

normally. Connect both the PDS module and the Host PC to the same sub network or the same

Ethernet Switch, and apply power to the PDS module.

2. Configure the correct network settings for the required PDS module. Refer to PDS Quick Start Guide for

more detailed information.

(http://ftp.icpdas.com/pub/cd/8000cd/napdos/pds/pds-700/document/quick_start/)

3. Download the “Terminal.exe”on your PC, or use other telnet client program. The “Terminal.exe”can

be downloaded from the ICP DAS web site.

(http://ftp.icpdas.com/pub/cd/tinymodules/napdos/software/)

4. Double click the “Terminal.exe”to open “Configuration Settings”dialog box.

5. Click the “TCP/IP Port”tab to configure the parameters as follows:

5-1: Type the “IP address of the PDS module”in the “IP Address”field.

5-2: Type the “10000”in the “TCP/IP Port”field.

5-3: Click the “Open COM”button.



6. Select the “Hex/Text”option in the “Display”filed and settings configuration command:

Command

Description

26SAVE=1, HTTP=1

Enables the Web Server and save the configuration to EEPROM.

26SAVE=1, HTTP=0

Disables the Web Server and save the configuration to EEPROM.

7. Type the “26SAVE=1, HTTP=1”string in the “send”field then click the “Send”button.

8. If the response is received, it will be displayed in the received field that means the success.

9. Reboot the PDS module to complete the configuration.







Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA ECAT-2016N Bedienungsanleitung

ICP DAS USA

ICP DAS USA WF-2026 Bedienungsanleitung

ICP DAS USA

ICP DAS USA DL-10 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7055D Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD4P2C2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7064 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tET Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7033D Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-2533 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PROFIBUS PROFI-2510 Bedienungsanleitung

ICP DAS USA

ICP DAS USA DS-2200 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tSH-700 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tPET-P6 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7H16M Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ISN-101 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8213W-4G Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7052D Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7033 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAT-2050 Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3016 Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-785 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAT-2061 Bedienungsanleitung

ICP DAS USA

ICP DAS USA WF-2017 Bedienungsanleitung

ICP DAS USA

ICP DAS USA LP-8 21 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung