ICP DAS USA PROFI-5045 Bedienungsanleitung

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PROFI-5053

PROFIBUS Remote I/O Module

Quick Start Guide

 Introduction

This user guide introduces the user how to implement the PROFI-5000

into their applications in a quick and easy way. Therefore, it only provides

the basic instructions. For more detail information about the PROFI -5000

module, please refer to the PROFI-5000 user manual in the ICP DAS

product CD or download it from ICP DAS web site.

 PROFI-5000 Connector and Pin Assignment

Pin No.

Signal

Meaning

B-Line

Receive/Transmit data – plus

GND

Power ground of active terminator

Power 5 volt of active terminator

A-Line

Receive/Transmit data - minus

The PROFIBUS connector is a standard 9 -pin D-Sub connector, there are

only 4 pins used in PROFI-5000. The pins VP and GND support the 5 volt

power to active terminal resistor, and the A-Line and B-Line is the data bus.

Status Indicator

PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-

5052/ PROFI-5053/ PROFI-5055/ PROFI-5060

It provides two types of status indicator, they are PWR

LED (Red) and RUN LED (Green).

Status Indicator

Meaning

Recommend solution

PWR ON

Master not Ready,

1. Check the address setting

Address not Match

of module and DP-master.

RUN OFF

Sets the DP-Master to

Cfg Fault

operation mode.

Make sure of the

consistency of Module

Selection.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PWR ON &

Module is in clear mode

N/A

RUN ON

or operation mode.

 PROFI-5017/ PROFI-5017C/ PROFI-5018/ PROFI-5024

It provides three types of status indicator, they are PWR

LED (yellow), ERR LED (red) and RUN LED (green).

When the power is supplied to module, PWR LED will

turn on; If CHK_CFG procedure is finished, RUN LED will

turn on and ERR LED will turn off. The table explains the

relationship between them.

Status Indicator

Meaning

Recommend solution

ERR ON &

Offline Mode

Check the address setting of

RUN OFF

module and DP-master.

ERR Flash(0.1 sec)

Stop Mode

Check the DP-Master is ready

to communicate with module.

Check the setting of module in

ERR Flash(0.5 sec)

Prm Fault

the master interface and make

sure of the consistency.

ERR Flash(1 sec)

Cfg Fault

Same as above

ERR ON & RUN

Clear Mode

Sets the DP-Master from clear

mode to operation mode

ERR OFF &

Operate Mode

RUN ON

PWR &

Diag Exist

Check the Input/Output value

ERR Flash

(Diag. Msg.

that if exceed/under the limit

lnterlace(0.5 sec)

Request)

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

 Terminating Resistors

In order to minimize the reflection effect of the signal transmission, PROFIBUS

device has to fit with an active terminal resistor at both first node and last node.

The connection of active terminating resistors is shown in above circuit diagram.

The PROFI-5000 doesn’t have any terminating resistors inside. Therefore, users

must add the terminator in external. In general, PROFIBUS connector has

terminating resistors inside, and there is a switch to control the ON/OFF of the

terminating resistors, as shown below.

Terminator ON

Terminator OFF

Terminator Switch

 Node Address

According to PROFIBUS specification, the station address which from 0 to 126 is

valid, and the address 126 is a special address that supports the remote setting

SSA telegram from Class 2 DP-Master.

 PROFI-5045/ PROFI-5050/ PROFI-5051/ PROFI-5052/

PROFI-5053/ PROFI-5055/ PROFI-5060

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

-The figure shown above is the decimal rotary switch. It dominates

the node (station) address of PROFI-5000. The left side switch is

high nibble of address and the other one is low nibble of address.

- It doesn’t support SSA service for setting node address.

EX 1 : MSB = 2, LSB = 3, node address => (2*10+3) = 23

 PROFI-5017/ PROFI-5017C/ PROFI-5018/ PROFI-5024

- The figure shown above is the decimal rotary switch. It dominates

the node (station) address of PROFI-5000. The switch is which

labeled MSB is high nibble of address and the other one is low

nibble of address.

- Module applies the setting of rotary switch as its address if the

address is valid. While the address is invalid, module loads the pre-

saved value from EEPROM. Moreover, if the address is invalid

(126) again, module awaits the SSA telegram and applies it. (Note:

If you want to clear the setting stored at EEPROM, you just adjust

rotary switch to FF before the power supplied).

Rotary

Pre-saved address

SSA Telegram

PROFI-5017(C)

Switch(dec)

(EEPROM)

Station Address

0~125

Do not care

No Accept

Rotary Switch

126~254

0~125

No Accept

Pre-saved

address(EEPROM)

126(default)

Accept with

SSA Telegram and

address 0~125

save address to

EEPROM

127~254

impossible

N/A

255

Clear to 126

Accept with

SSA telegram and

address 0~125

save address to

EEPROM

EX 1 : MSB = 0, LSB = B, node address => (0*16+11) = 11

EX 2 : MSB =7, LSB = 9, node address => (7*16+9) = 121

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

 PROFI-5000 – Setting and Module installation

(example for SIMATIC Step 7)

The following steps can help users to set and apply the PROFI-5000.

1. Address Setting:

2. Load GSD file into the DP-Master Configuring software a.

Open HW Config

b. Select Option -> Install GSD files

c. Click “Browse” to select GSD file, and then click “Install”

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

d. Install OK

3. Select I/O modules

a. Choose PROFI-5000

b. add I/O module that you want to use.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

c. Modify system parameters and module parameters(modify by user’s

preference)

 System parameters: Double click PROFI-5000

 Module parameters: Double click module

4. Download Setting and Program into DP-Master

Users load the setting and program into DP-Master, and let it go.

a. Select Station -> Save and Compile

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

b. Select PLC -> Download

After the procedure finish, DP-Master will establish the connection with

PROFI-5000 and execute program automatically. RUN_LED indicates the

status of connection that you can observe.

PROFI-5053 PROFIBUS DAQ Module - QuickStart (Apr/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PROFI-5000 Quick Start (Version 2.1, June/2013) ------8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA PDS-220F Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tET-P6 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8124W Bedienungsanleitung

ICP DAS USA

ICP DAS USA WF-2051 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD5 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7051 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7000 series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tGW-700 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA DS-700 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PET-AR400 Bedienungsanleitung

ICP DAS USA

ICP DAS USA MDC-700 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7052D Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O Bedienungsanleitung

ICP DAS USA

ICP DAS USA GTM-204M-4G Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7067D Bedienungsanleitung

ICP DAS USA

ICP DAS USA MDC-700 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-7063D Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-3133-RCT Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA tSH-735 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7024 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7033D Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7069 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7065 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PM-4324 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung