ICP DAS USA I-7063D Bedienungsanleitung

I-7063D 8-ch DI and 3-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

I-7063D

8-channel Isolated Digital Input and 3-

channel Relay Output Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/i_7063_i_7063d.html

1. Introduction

I-7063 is intelligently designed to provide signal conditioning system monitoring and

safe value settings. I-7063 is a cost-effective solution for a wide range of valuable

industrial control signals and systems. The DCON utility can help users to configure and

test I-7063 power relay output module. Plenty of library functions and demo programs

are provided to let users develop programs easily under Windows, Linux and DOS

operating systems. The communication interface is modbus protocol via RS-485. Users

may mount the modules on a DIN rail, panel or wall. Modules have a screw-terminal

block to connect to the signals.

2. Terminal Assignment

I-7063D 8-ch DI and 3-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

I-7063D 8-ch DI and 3-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Default Settings

Default settings for the I-7064/D DIO modules are as follows:

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

5. Configuration

To install the module, follow the steps below:

1. Connect the analog output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

I-7063D 8-ch DI and 3-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

I-7063D 8-ch DI and 3-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

I-7063D 8-ch DI and 3-ch Relay Output Module- QuickStart (Jan/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Inhaltsverzeichnis

Andere ICP DAS USA Steuereinheit Handbücher

ICP DAS USA

ICP DAS USA I-7014D Bedienungsanleitung

ICP DAS USA

ICP DAS USA GW-7552-M Bedienungsanleitung

ICP DAS USA

ICP DAS USA tET-P6 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8094 Stücklistenhandbuch

ICP DAS USA

ICP DAS USA M-7019Z Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-P3R3 Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3227 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7065 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7000 series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ISN-101 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7051D Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7000 series Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7051 Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-7015 Bedienungsanleitung

ICP DAS USA

ICP DAS USA SG-3016 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-TH8 Bedienungsanleitung

ICP DAS USA

ICP DAS USA I-8092F Stücklistenhandbuch

ICP DAS USA

ICP DAS USA LP-8 21 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA WF-2026 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PROFIBUS PROFI-2510 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PDS-220F Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA ET-87P2 Bedienungsanleitung

ICP DAS USA

ICP DAS USA M-7053D Bedienungsanleitung

ICP DAS USA

ICP DAS USA ECAT-2000 Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung