ICRealtime AVS-4MD4025-IR Bedienungsanleitung
HDAVS Camera User’s Manual
Version 1.0.0
i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
2Device Framework .....................................................................................................................2
3Installation....................................................................................................................................3
4Menu.............................................................................................................................................5
4.1 HAVR Settings..............................................................................................................5
4.2 Menu Operation............................................................................................................5
Appendix ⅠMaintenance...................................................................................................................7
ii
Welcome
Thank you for purchasing our HDAVS camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated DC 12V or AC24V in the IEC60950-1. (Power supply requirement is
subject to the device label).
Please install easy-to-use device for power off before installing wiring, which is for emergent power
off when necessary.
Please check if the power supply meets the requirements of working voltage of the camera before
operating the device (The material and length of the power supply cable will influence terminal
voltage value).
Please prevent the line cord from being trampled or pressed, especially the plug, power socket and
the junction from the device.
2．Environment
Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus.
Please transport, use and store the device within the range of allowed humidity and temperature.
Please do not allow water and other liquid falling into the camera in case that the internal
components are damaged.
Please keep the sound ventilation in case of heat accumulation.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
Please pack the device with standard factory packaging or material with same quality when
transporting the device.
It is recommended to use the device together with lightning protection device to enhance lightning
protection effect.
It is recommended to GND the device to enhance device reliability.
It is advised to use qualified video transmission cable to improve video quality. It is recommended
to use RG59 coaxial cable or higher standard.
Warning
Please use the standard accessories provided by manufacturer and make sure the device is
installed and fixed by professional engineers.
Please prevent the device surface from the radiation of laser beam when using laser beam device.
iii
Please do not provide two or more power supply modes for the device, otherwise it may cause
damage to the device.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded content will
be added in the manual without prior announcement.
Please contact the customer service for the latest procedure and supplementary documentation.
The company is not liable for any loss caused by the operation which is not followed by the manual.
Please refer to the company’s final explanation if there is any doubt or dispute.
1
1General Introduction
1.1 Overview
This series HDAVS camera conforms to the HDAVS standard. It supports video signal high-
speed long distance transmission without any delay. It can be controlled by the HAVR
conforming to the HDAVS.
1.2 Features
Adopt high performance CMOS image sensor, megapixel definition.
Support coaxial transmission of video, audio and control signal.
For 720P series, support RG59 coaxial cable transmission without any loss. The distance
is over 800m. For 1080P, 4M and 4K series, support RG59 coaxial cable transmission
without any loss. The distance is over 500m.
High speed, long distance real-time transmission.
Support HDAVS HD video and analog video output.
Support 3D noise reduction, excellent low illuminance performance.
Support ICR switch to realize surveillance both in the daytime and at night.
Support OSD menu adjustment parameters.
Support smart IR function.
Support WDR/DWDR function.
Support DC 12V power supply. (Some models support DC 12V/AC 24V power supply).
Support IP67 compliance.
Support IK10 compliance. (Only supported by vandal proof camera)
Can be applied to environments which requires high definition image, such as banking,
supermarket, telecom, government, school, airport, factory, hotel, museum and etc.
2
2Device Framework
See Figure 2-1 for the dimension.
Figure 2-1
See Figure 2-2 for the cable ports.
Figure 2-2
3
3Installation
Dome camera mainly uses ceiling installation; installation surface includes ceiling and wall.
Users can install the device with the installation position map and the screws in the
accessories bag.
Attention:
Please install the device in time after it is taken apart, which is to avoid the camera
module being exposed to damp environment for too long.
Before the installation, please make sure the installation surface is thick enough to sustain
at least 3X weight of the camera.
Figure 3-1
Note:
The installation figure is for reference only.
Step 1
Take out the installation position map from the accessories bag, and paste it on the ceiling or
wall according to the cable exit location, dig holes on the installation surface according to the
installation position map, take out the expansion bolts from the accessories bag and insert
them into the installation holes and fix them.
Step 2
Use the wrench to loosen the locking screw in the cover and take down the cover.
Step 3
Adjust the location of the dome pedestal according to the top cable outlet or side cable outlet.
Pull the cable out through the side outlet of installation surface and pedestal (please skip the
step if it is top cable outlet), aim the screw fixing holes of dome pedestal to the fixing holes of
4
expansion boles on the installation surface, then insert the self-tapping screws into the
expansion bolts and secure them firmly, fix the dome on the installation surface.
Step 4
Connect the video output port of the device cable to the back-end HAVR device and connect
the power port to power.
Step 5
Install the dome enclosure; install the enclosure which is taken down in step 2 back to the
dome pedestal.
So far you have completed device installation and cable connection, you can check device
monitoring image via back-end coding device.
5
4Menu
4.1 HAVR Settings
This HDAVS camera series can adjust OSD menu via coaxial control. After connected the
camera to the HDAVS series HAVR, from Main Menu->Setting->System->PTZ, you need to
select the channel number for access and set control mode as HDAVS and the protocol as
ICR-SDI. Click “Save”button to save current setup. See Figure 4-1.
Figure 4-1
4.2 Menu Operation
Click the right mouse button and select “PTZ Control”, then you will see the “PTZ Setup”menu,
which is as shown in Figure 4-2 and Figure 4-3.
Figure 4-2
6
Figure 4-3
See Sheet 4-1 for the details of button functions.
Button
Function
Open menu
、
Select menu item
、
Select menu value
Adjust lens zoom and auto
trigger focus
Note:
Some of the buttons can only
be applied for the motorized
vari-focal camera.
Adjust lens focus
Auto focus under current
zoom rate
Lens reset
Sheet 4-1
If there is “ ”, click the “Confirm”button in “Menu Operation”interface to go to the 2nd menu.
Click “Return” button to go back to the previous menu interface.
Inhaltsverzeichnis
Andere ICRealtime Sicherheitskamera Handbücher
ICRealtime
ICRealtime ICIPD1300 Bedienungsanleitung
ICRealtime
ICRealtime ICR-220-IR Bedienungsanleitung
ICRealtime
ICRealtime PTZ-N23X4-S Bedienungsanleitung
ICRealtime
ICRealtime IPEL-MB80F-IRW1 Bedienungsanleitung
ICRealtime
ICRealtime AVS-B2218Z Bedienungsanleitung
ICRealtime
ICRealtime ICIP2040IR Bedienungsanleitung
ICRealtime
ICRealtime HD-AVS Bedienungsanleitung
ICRealtime
ICRealtime ICIP-B1300 Bedienungsanleitung
ICRealtime
ICRealtime AVS Series Bedienungsanleitung
ICRealtime
ICRealtime EL-3000 Bedienungsanleitung
ICRealtime
ICRealtime AVSD2208VF Bedienungsanleitung
ICRealtime
ICRealtime ICIP B3000AF Bedienungsanleitung
ICRealtime
ICRealtime EL-3000N Bedienungsanleitung
ICRealtime
ICRealtime ICIP-D1300 Bedienungsanleitung
ICRealtime
ICRealtime PTZ-3660SIR Bedienungsanleitung
ICRealtime
ICRealtime EL-2000 I-sniper Bedienungsanleitung
ICRealtime
ICRealtime ICR540VD Bedienungsanleitung
ICRealtime
ICRealtime EL-790 Bedienungsanleitung
ICRealtime
ICRealtime F Series Bedienungsanleitung
ICRealtime
ICRealtime ICIP-D2360 Bedienungsanleitung
