ICRealtime HD-AVS Bedienungsanleitung
Quick Start Guide
HD-AVS Dome
PTZ Camera
Features and Specifications
A. Overview
B. Cable Interface
Camera Installation
A. Installation Steps
B. Dip switch diagram
OSD and PTZ Functions
A. OSD Operation
B. OSD Menu Functions
C. Function Settings
FAQ and Lightning Protection
A. FAQ
B. Lightning Protection
2
2
3-4
5
5
6
6-7
8
8-9
Table Of Contents
MARGIN
GUIDES
To see the guides to go:
View / Guides / Show
Guides
www.icrealtime.com
IMPORTANT SAFEGUARDS AND WARNINGS
Electrical Safety
All installation and operation here should conform to your local electrical safety codes. The
power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated DC12V/5A ± 25% (See product datasheet for the most accurate
power requirement specification). We assume no liability or responsibility for all the fires or
electrical shock caused by improper handling or installation. We are not liable for any problems
caused by unauthorized modification or attempted repair.
Transportation Security
Care must be given to avoid heavy stress, violent vibration or water damage during
transportation, storage and installation.
Installation
Do not apply power to the camera before completing installation. Please install the proper
power cut-off device during the installation connection. Always follow the instruction guide the
manufacturer recommended.
Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers. We are
not liable for any problems caused by unauthorized modifications or attempted repair.
Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc. Please keep it away from the electromagnetic
radiation object and environment. Please make sure the CCD (CMOS) component is out of the
radiation of the laser beam device. Otherwise it may result in CCD (CMOS) optical component
damage. Please keep the sound ventilation. Do not allow the water and other liquid falling into
the camera. Lightning-proof device is recommended to be adopted to better prevent lightning
damage. The grounding studs of the product are recommended to be grounded to further
enhance the reliability of the camera.
Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily
maintenance work. Do not touch the CCD (CMOS) optic component. You can use the blower to
clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is
too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect
the CCD (CMOS) component when you do not use the camera.
Accessories
Be sure to use all the accessories recommended by manufacturer. Before installation, please
open the package and check all the components are included. Contact your local retailer ASAP
if something is broken in your package.
1A. OVERVIEW
This series PTZ camera utilizes High Definition Advanced Video
System (HD-AVS) technology, an HD-over-coaxial cable video
standard that allows long-distance, HD transmission of video,
audio, and control functions. The camera supports TVI, AHD and
CVBS (SD) using the dip switch.
The camera supports DC24V/2.5A ± 25%, and draws from: 9.6W
to 22W. It also is IP66 and IK10 rated with TVS 6000V lightning
protection; surge protection, making it a suitable choice for
outdoor environments.
Note: Take careful steps when handling the camera. See figure
1-1.
1B. Cable Interface
See Figure 1-2.
1. FC Connector
2. DC Power input
3. 24VAC input: Red(+), Black(-), Yellow/Green (ground)
4. RS485: Yellow (A+), Orange (B-)
5. Video output
6. Ethernet port (on some models)
7. Audio IO: White- Input, Red-Output, Black-Ground
8. Alarm IO: Blue: Alarm output 1, Black: Alarm output 2, Green: Contact
switch 1, Pink: Contact switch, Yellow-green: Grounding cable, Red: Alarm
input 1, Brown: Alarm input 2, Grey: Alarm input 3, Light green: Alarm
input 4, Purple: Alarm input 5, White: Alarm input 6, Yellow-black: Alarm
input 7
Figure 1-2
MARGIN
GUIDES
To see the guides to go:
View / Guides / Show
Guides
2 | www.icrealtime.com
Figure 1-1
2A. INSTALLATION STEPS
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
3 | www.icrealtime.com
Step 1 Remove the installation map from the packaging and place in
the installation surface. Drill out the appropriate mounting holes and
cable exit, if necessary after setting the position map. See Figure 2-1.
Step 2 For outdoor installation, four rubber grommets are provided for
the mounting screws to waterproof the base. See Figure 2-2.
Step 3 Remove the dome cover using the wrench provided. Thread the
cabling through the cable exit on the installation surface and install the
mounting screws as shown in Figure 2-3.
Step 4 Connect the necessary cabling to the camera. See Figure 2-4.
Figure 2-2
Figure 2-1
Figure 2-4
Figure 2-3
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
4 | www.icrealtime.com
Step 5 Replace and secure the dome cover as shown in Figure 2-5.
Step 6 It is recommended to waterproof any outdoor cabling. See
Figure 2-6.
Figure 2-5
Figure 2-6
2B. Dip switch settings
See Figure 2-7 for Cover location and dip switch settings.
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
5 | www.icrealtime.com
Figure 2-7
Figure 3-1
3A. OSD Operation
To open the On Screen Display (OSD) make sure you set the protocol
under Main Menu-> Camera-> PTZ. Make sure the Channel the PTZ
is occupying is set to AVS mode.
Step 1 Using a mouse and a local display, right click on the live view
and select PTZ control. The PTZ menu will populate. See Figure 3-1.
Step 2 Click to open PTZ Control Panel then click to open
OSD. The Use the up and down buttons to select menu item and the
left and right to change parameter values. Click Enter to confirm. See
Figure 3-2.
Figure 3-2
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
6 | www.icrealtime.com
3B. OSD Menu Functions
See the table below for Menu Index.
System Setting System Information; Addr
Information; Count Information;
System Time Setting; Set North;
Language; Switch Type; Video
Output; Audio Mode; Factory
Default; Restart
Display Setting Preset Title; Azimuth Disp; Time
Disp; Position; Zoom Disp; Inside
Temp; Title Disp; Alarm Disp;
Pattern Disp
Camera Setting WB Setting; Exposure Setting;
Day/Night Setting; Focus Setting;
Image Adjust; Defog Setting; Zoom
Speed; Sharpness; Sharpness
Restrain; Digital Zoom; Picture
Flip;Lens Init; Picture Mode; Camera
Maintain; Camera Factory Default;
Camera Restart
Function Setting Preset; Auto Pan; Auto Scan; Tour;
Pattern; Idle Motion; Auto Run;
Privacy Masking; PTZ Speed; Set
Zero; Power Up; Menu Password;
Menu Idle; Channel Title; PTZ Auto
Stop; Warm Machine; PTZ
Correction
Alarm Setting Alarm No; Action; Parameter;
Contact; Relay Out; Reset Delay
IR Light Setting IR Sensitivity; IR Light Ctrl; Near
Light; Far Light; IR Light Comp
3C. Function Settings
Presets- These are positions the PTZ can move to,
●Preset No : You can select different preset numbers to modify.
●Title: You can name the preset (optional).
●Setting: Select this option after moving the PTZ to the
desired position to save the preset in that position.
●Call: This will move the PTZ to this preset (if saved)
Pan- This is the 360° horizontal rotation of the PTZ at a certain
speed.
●Pan Speed: Select the speed of the Pan.
●Run: Enable Pan action
●Stop: Stops Pan action.
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
7 | www.icrealtime.com
Figure 3-4 Figure 4-2
3D. Function Settings (continued)
Scan- This is the horizontal rotation of the PTZ with defined left and
right limits.
●Auto Scan No : You can select different scan numbers to
modify.
●Set Left/ Right limit: You can select the left/ right limits on
this PTZ. Select one option, move the camera to the
appropriate limit then click Enter. “OK” will be displayed if set
successfully.
●Scan Speed: Select the speed of the Scan movement
●Call: This will enable the Scan motion.
●Stop: This will cancel the scan motion.
Tour- A tour is an action the will move to the different preset
positions at specified time intervals.
●Tour No: You can select between different Tour numbers
●Setting: You will be able to select the presets for the tour,
dwell time and speed. See Figure 3-4.
●Delete: Deletes current tour setting
●Call: Starts the Tour action
●Stop: Cancels Tour action.
Pattern- This a recorded set of movements that the PTZ will follow.
●Pattern No : You can select different scan numbers to
modify.
●Program Start: This records the pattern movement. Click
Enter to start. An “OK” will flash indicating the PTZ
movements will now be recorded. Move the PTZ as desired.
●Program End: Select this option after you have finished
recording your pattern.
●Call: Starts the recorded pattern movement.
●Stop: This will cancel the pattern movement.
Idle Function- Is a defined operation when the Device does not
receive any valid command within a certain period.
●Idle Function: Turns Idle Function on or off.
●Idle Time: The time delay where the PTZ will activate the Idle
function if no commands are sent
●Idle Action: Select the idle action type between: None, Preset,
Scan, Tour, and Pattern
●Parameter: Number of selected function
Power Up- This is the automatic operation of the Device after it is
powered on.
●Power Up: Sets action of: Auto, Preset, Scan, Tour, Pattern
and None. If set to auto, the camera will resume the previous
action before it powered down.
●Parameter: Number of selected function
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
8 | www.icrealtime.com
No self-test and no
image after the
Device is powered on
●Check whether the power supply is
properly connected.
●Camera may be underpowered.
Check power.
●Check whether the main power and
transformer are working normally.
Self-test can not be
performed, or there is
noise
●Use the required power supply.
●Contact support as there may be
mechanical failure.
Video signal loss
occurs when the
Device is in
high-speed rotation
●Insufficient power, use the required
power supply
Image is not stable ●Poor contact on circuits. Connect the
cable properly.
Blurry image.
●Lens glass is dirty. Clean the lens.
●Focus is in manual mode. Set Focus
settings on PTZ,
4A. FAQ 4B. LIGHTNING PROOFING AND SURGE PROTECTION
This PTZ adopts TVS lighting protection technology. It can
effectively prevent damages from various pulse signals below
6000W, such as sudden lighting and surge. Necessary precaution
measures should be taken in accordance to local guidelines when
installing the speed dome in an outdoor environment.
●The signal transmission cable and high-voltage device (or
high-voltage cable) should be at least 50 meters apart.
●If possible, route cables through a properly grounded and
shielded underground conduit.
●In areas of strong lightning occurrence or near high sensitive
voltage (such as near high-voltage transformer substation), it is
required to install additional a high-power lightning protection
device or lightning rod.
●Electrical bonding is recommended. The ground device should
meet anti-jamming requirements and conform to your local
electrical safety code. The ground device should not short
circuit to N (neutral) line of high voltage power grid or mixed
with other wires. When connecting the system to the ground
alone, the grounding resistance should not be more than 4Ω ,
and the earth cable cross-sectional area should be no less than
25 mm². See Figure 5-1.
●For indoor usage, The yellow and green GND wire or GND
screw of the speed dome should be reliably connected by
several strands of copper wire with no less than 25mm²and
indoor equipotential GND terminal. Please refer to Figure 5-2
for lightning proof installation mode.
MARGIN
GUIDES
Stay within the yellow
box. Do not let text go
beyond, instead move
to the next column or
start a new page.
9 | www.icrealtime.com
Figure 5-1 Figure 5-2
4B. LIGHTNING PROOF AND SURGE PROTECTION (Continued)
Andere Handbücher für HD-AVS
2
Inhaltsverzeichnis
Andere ICRealtime Sicherheitskamera Handbücher
ICRealtime
ICRealtime ICR650VD Bedienungsanleitung
ICRealtime
ICRealtime ICIP2040IR Bedienungsanleitung
ICRealtime
ICRealtime ClearView WiFi-2MP-BL100 Bedienungsanleitung
ICRealtime
ICRealtime ICIP-B2001-IR Bedienungsanleitung
ICRealtime
ICRealtime HD-AVS Bedienungsanleitung
ICRealtime
ICRealtime AVS-B2100 Bedienungsanleitung
ICRealtime
ICRealtime AVSD2218Z Bedienungsanleitung
ICRealtime
ICRealtime Elite Series Bedienungsanleitung
ICRealtime
ICRealtime ICHD850VDIR Bedienungsanleitung
ICRealtime
ICRealtime Full HD(HD-SDI) CCTV Box Camera Bedienungsanleitung
ICRealtime
ICRealtime F Series Bedienungsanleitung
ICRealtime
ICRealtime IPEL-M60F-IRW1 Bedienungsanleitung
ICRealtime
ICRealtime ICIPD3000 Bedienungsanleitung
ICRealtime
ICRealtime ICIP-D2000-IR-B Bedienungsanleitung
ICRealtime
ICRealtime ICIP-B2000 Bedienungsanleitung
ICRealtime
ICRealtime F Series Bedienungsanleitung
ICRealtime
ICRealtime ICIP-MP1801S Bedienungsanleitung
ICRealtime
ICRealtime ICIPD2730 Bedienungsanleitung
ICRealtime
ICRealtime ICIP360L6 Bedienungsanleitung
ICRealtime
ICRealtime HD Pinhole Bedienungsanleitung
