Icron USB-2000 Bedienungsanleitung

USB 2.0 USB-2000

Thank you for purchasing the USB-2000. Please read this guide

thoroughly before installation.

FCC Radio Frequency Interference Statement Warning

The USB-2000 have been tested and found compliant with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when installed and

operated in a commercial environment. The USB-2000

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with this user guide, may cause harmful interference

to radio communications. Operation of the USB-2000 in a residential area is likely

to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

CE Statement

We, Icron Technologies Corporation, declare under our sole responsibility

that the USB-2000, to which this

declaration relates, are in conformity with European Standard EN 55022/A1

Class A, and EN 50082-1 (IEC 801-2, IEC 801-3, IEC 801-4)

IC Statement

These Class A digital apparatus complies with Canadian ICES-003.

Technologies Corporation, the Icron Technologies Corporation logo, and the

Icron Technologies Corporation products referred to herein are either the

trademarks or the registered trademarks of Icron Technologies Corporation.

All other trademarks are property of their respective owners. Icron

Technologies Corporation assumes no responsibility for errors that may

appear in this manual. Information contained herein is subject to change

without notice.

User Guide

Contents

Introduction................................................................................................ 1

USB-2000 Product Contents...................................................................... 1

About the USB-2000.................................................................................. 2

Before You Begin ...................................................................................... 5

Installing the LEX unit............................................................................... 5

Installing the REX unit .............................................................................. 5

Connecting the LEX unit to the REX unit ................................................. 5

Checking the Installation............................................................................ 6

Connecting a USB Device ......................................................................... 6

Troubleshooting......................................................................................... 7

Specifications............................................................................................. 9

Limited Hardware Warranty .................................................................... 11

Hardware Remedies................................................................................. 11

Limitation of Liability.............................................................................. 11

Obtaining Warranty Service..................................................................... 12

Contacting Technical Support.................................................................. 12

USB-2000

Notes

User Guide

Introduction

This manual is intended to assist IT professionals install the USB-2000.

The instructions in this guide assume a general

knowledge of computer installation procedures, familiarity with cabling

requirements, and some understanding of USB devices. The USB-2000

reference used for the remainder of this document applies to either the -2 or

-4 model.

NOTE:Notes give additional information that could make installation

easier.

USB-2000 Product Contents

When you open your USB-2000 for the first time you should find the

following items:

• USB-2000 User Guide

• Local EXtender (LEX) unit.

• Remote EXtender (REX) unit.

• AC power adapter (2 units)

• USB cable (2m long)

To complete the installation, you will also require the following items that

are not included with the product:

• USB compatible computer

• USB device

• 2-strand fiber-optic cable with Duplex LC connectors (if using

surface cabling),

OR,

2-strand fiber-optic cabling with two information outlets and two

2-strand fiber-optic patch cords with Duplex LC connectors (if

using premise cabling)

NOTE:For the USB-2000, the maximum length of the

multimode fiber-optic (MMF) cable, including patch cords, must

not exceed 500m on 50/125µm MMF or 300m on 62.5/125µm

MMF.

NOTE: For the USB-2000, the maximum length of the

singlemode fiber-optic (SMF) cable, including patch cords, must

not exceed 10 km on 9/125µm SMF

USB-2000

About the USB-2000

The USB-2000 incorporates Icron’s ExtremeUSB® technology. This

technology breaks the five-meter distance barrier for the connection of USB

peripheral devices and allows users to enjoy the benefits of USB technology

beyond the desktop.

With the USB-2000, utilizing multimode fiber, USB devices can

be located up to 500 meters from the host computer.

With the USB-2000, utilizing singlemode fiber, USB devices can

be located up to 10km from the host computer.

The USB-2000 is composed of two individual units, the LEX unit and

the REX unit. Note that there are no physical differences between the

-2 and -4 units. The only difference is the -2

units ship with multimode SFP modules supporting a maximum reach of

500m, and the -4 units ship with singlemode SFP modules

supporting a maximum reach of 10km.

The LEX unit: USB-2000

The LEX unit connects to the host computer using a conventional

USB cable.

The LEX unit is powered by an external AC adapter.

Front

View

1Host LED

2Host Port (USB Type B)

3Link LED

4Link Port (Duplex LC)

5Power LED

6Power connector

User Guide

The REX unit: USB-2000

The REX unit connects to a USB device using a conventional USB

cable. The REX unit allows you to connect up to four USB devices.

Additional devices may be connected by attaching a conventional

USB hub to the REX unit.

The REX unit is powered by an external AC adapter.

Front

View

Rear

View

1Power LED

2Power connector

3Device LEDs

4Device Ports (USB Type A)

5Link LED

6Link Port (Duplex LC)

USB-2000

Network Cabling

USB-2000-2

The LEX unit and the REX unit are interconnected by up to 500 meters of

fiber-optic cabling. Two strands of 50/125µm MMF or 62.5/125µm MMF

cabling are required. The cabling subsystem must provide a duplex

connection with crossover, and must be terminated with Duplex LC

connectors at both ends.

USB-2000-4

The LEX unit and the REX unit are interconnected by up to 500 meters of

fiber-optic cabling. Two strands of 9/125µm SMF cabling are required. The

cabling subsystem must provide a duplex connection with crossover, and

must be terminated with Duplex LC connectors at both ends.

Fiber-optic cable

USB USB

LEX REX

cable cable(s) USB

device(s)

computer

AC power adapters

USB Cables

USB cables have two distinct connectors. The Type A connector is used to

connect the cable from a USB device to the Type A port on a computer or

hub. The Type B connector is used to attach the USB cable to a USB device.

USB Type A

port USB Type A

connector USB Type B

port USB Type B

connector

Compatibility

The USB-2000 complies with USB 2.0 specifications governing the

design of USB devices. However, Icron Technologies Corporation does not

guarantee that all USB devices are compatible with the USB-2000.

User Guide

Before You Begin

Before you can install the USB-2000, you need to prepare your site.

1. Determine where the host computer is to be located and set up the

computer.

2. Determine where you want to locate the USB device(s).

3. If you are using surface cabling, ensure you have enough fiber-optic

cabling to connect the two locations.

If you are using premise cabling, ensure fiber-optic cabling is

installed between the two locations, with fiber-optic information

outlets located near both the computer and the USB device.

Installing the LEX unit

1. Place the LEX unit near the host computer.

2. Plug the power adapter into a suitable AC outlet.

3. Connect the power adapter to the LEX unit.

4. Plug the Type B connector on the USB cable (included) into the

Host port on the LEX unit.

5. Plug the Type A connector on the USB cable into a USB port on the

host computer.

NOTE:The host computer must be equipped with an EHCI (USB 2.0) host

controller. Support for OHCI/UHCI (USB 1.1) host controllers is

not provided.

Installing the REX unit

1. Place the REX unit near the USB device(s).

2. Plug the power adapter into a suitable AC outlet.

3. Connect the power adapter to the REX unit.

Connecting the LEX unit to the REX unit

With Surface Cabling

1. Plug one end of the fiber-optic cabling (not included) into the Link

port on the LEX unit.

2. Plug the other end of the fiber-optic cabling into the Link port on the

REX unit.

USB-2000

With Premise Cabling

1. Plug one end of a fiber-optic patch cord (not included) into the Link

port on the LEX unit.

2. Plug the other end of the patch cord into the fiber-optic information

outlet near the host computer.

3. Plug one end of the second fiber-optic patch cord (not included) into

the Link port on the REX unit.

4. Plug the other end of the second patch cord into the fiber-optic

information outlet near the USB device.

NOTE:If you are installing a USB-2000 unit, the

maximum length of the fiber-optic cable, including patch cords,

must not exceed 500 meters.

NOTE: If you are installing a USB-2000 unit, the

maximum length of the fiber-optic cable, including patch cords,

must not exceed 10,000 meters.

NOTE: The cabling must provide a duplex connection with

crossover, and must be terminated with Duplex LC connectors at

both ends.

Checking the Installation

1. Check that the Power LEDs on the LEX unit and the REX unit are

both on.

2. Check that the Link LEDs on the LEX unit and the REX unit are

both on.

3. Check that the Host LED on the LEX unit is on.

4. On the host PC, open the Device Manager applet. Expand the entry

for Universal Serial Bus controllers by clicking the + sign. If the

USB 2.0 Ranger has been installed correctly you should find it

listed as a Generic USB Hub.

Connecting a USB Device

1. Install any software required to operate the USB device(s). Refer to

the documentation for the device(s), as required.

2. Connect the USB device to the Device port on the REX unit.

3. Check that the Device LED on the REX unit is on.

User Guide

Troubleshooting

The following table provides troubleshooting help. The topics are arranged

in the order in which they should be executed in most situations. If you are

unable to resolve the problem after following these instructions, please

contact technical support for further assistance (see page 12).

Symptoms/Cause Remedy

All LEDs on LEX unit are

off.

Cause:

The LEX unit is not

receiving power from the

adapter

1. Ensure that a power adapter is connected

to the LEX unit.

2. Check that the adapter is connected to a

live source of electrical power.

All LEDs on REX unit are

off.

Cause:

The REX unit is not

receiving power from the

adapter

1. Ensure that a power adapter is connected

to the REX unit.

2. Check that the adapter is connected to a

live source of electrical power.

Link LEDs on LEX unit and

REX unit are off.

Cause:

There is no connection

between the LEX unit and

the REX unit.

1. Ensure that a fiber-optic cable with

crossover is connected between the LEX

unit and the REX unit.

2. Connect a short fiber-optic crossover

patch cord between the LEX unit and the

REX unit. Recheck the operation of the

system.

Link LED on LEX unit is on;

Host LED on LEX unit is off.

Cause:

a) The computer is not

functioning.

b) The LEX unit is not

connected to the

computer.

c) The computer does not

support USB hubs.

d) The USB-2000 is

malfunctioning.

1. Disconnect all USB devices from the REX

unit.

2. Disconnect the LEX unit from the

computer.

3. Disconnect and then reconnect the power

adapter to the USB-2000.

4. Reconnect the LEX unit to the computer.

5. In the Universal Serial Bus controllers

section of Device Manager, check that

the USB-2000 is recognised as a

“Generic USB Hub”.

6. If the USB-2000 is not recognised,

contact technical support for assistance.

Inhaltsverzeichnis

Andere Icron Extender Handbücher

Icron

Icron USB 2.0 Ranger 2304GE-LAN Bedienungsanleitung

Icron

Icron RG2204 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304GE-LAN Bedienungsanleitung

Icron

Icron USB Ranger 2212 Bedienungsanleitung

Icron

Icron EL5353 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304SP Bedienungsanleitung

Icron

Icron USB Ranger 2201 Bedienungsanleitung

Icron

Icron USB 3-2-1 Raven 3104 Bedienungsanleitung

Icron

Icron EL4500 Bedienungsanleitung

Icron

Icron EL5100 Bedienungsanleitung

Icron

Icron USB Rover 2850 Bedienungsanleitung

Icron

Icron EL5100 Bedienungsanleitung

Icron

Icron DVI Ranger 500 Bedienungsanleitung

Icron

Icron RG2324 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304 Bedienungsanleitung

Icron

Icron EL5363 Bedienungsanleitung

Icron

Icron USB 3-2-1 Starling 3251C Bedienungsanleitung

Icron

Icron USB 2.0 Ranger 2311 Bedienungsanleitung

Icron

Icron 100 Bedienungsanleitung

Icron

Icron USB Ranger 2224 Bedienungsanleitung

Icron

Icron USB Rover 1850 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304GE-LAN Bedienungsanleitung

Icron

Icron VU5363 Bedienungsanleitung

Icron

Icron 00-00437 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung