ICW TITAN Bedienungsanleitung

If you have any questions, please call 1-800-558-4435

TITAN ARM INSTALLATION

T2 ARM INSTALLATION - rev 04/22/2014 pjm

Page 1 of 3

Detach the pole mount from arm using the provided

5mm hex key. Separate the two sections of the pole

mount using the provided 5/32 hex key. Place around

the pole you are mounting to and ﬁ rmly reassemble

the pole mount.

ATTACH POLEMOUNT TO POLE

ATTACH WALL

PLATE TO WALL

Locate stud and mark top

hole, drill 11/64 pilot hole

and insert #14 screw and

tighten slightly. Using a

level, mark lower hole

and drill pilot hole, insert

#14 screw and, with

unit level, tighten both

screws. ICW supplies

#14 wood screws. If

installing onto metal

studs, you will need

to replace with proper

metal stud fasteners.

MOUNT ARM

IF USING WALL MOUNT IF USING POLE MOUNT

ATTACH DESKMOUNT TO DESK

Please follow cable management

instructions before securing desk mount.

Drill a 3/8 hole through the

horizontal surface you intend to

mount to. Screw the 3/8 stud into

your desk mount as shown, the

stud is found in your hardware

bag.

Push the 3/8 stud on desk mount

through the hole in the desk and

slip the large mounting washer

over the stud from underneath

and secure in place with the 3/8

nylock nut.

Remember to detach

desk mount and feed

cords down through

the groove in the

desk mount - passing

through the bearing.

Then Re-attach desk

mount.

IF USING

DESK MOUNT

IF USING

WALL TRACK

MOUNT WALL

TRACK TO WALL

Using a phillips

drive, remove

the plastic cap

on one end of

the track. Save

this cap to put

back on when

everything is

ﬁ nished.

Locate the wall stud and

mark the top hole of the Wall

Track, drill 11/64 pilot hole

and insert #14 screw and

tighten slightly. Use a level,

mark the 7 lower holes, drill

pilot holes and then insert the

#14 screws. Use all 8 center

screw holes.

NOTE: #14 Wood screws are

supplied with unit. If installing

into metal studs, you will

need to replace these with

proper metal stud fasteners

T2 ARM INSTALLATION - rev 04/22/2014 pjm

TITAN ARM INSTALLATION

Page 2 of 3

ATTACH PARALINK KEYBOARD TO MONITOR

Attach the Paralink

Keyboard Mount to the

Monitor Mount by using

the 3/8-16 screw and lock

washer provided.

IF ATTACHING TO ULTRA FLIP-UP

IF ATTACHING TO PARALINK

ATTACH FLIP UP

1.Remove screws from

drop extension using

5/32” hex key.

2.Align holes in keyboard

tray with screw holes in

drop extension.

3.Attach keyboard tray

using the provided

screws.

ATTACH PARALINK

1.Remove beauty cap on

Paralink.

2.Remove screw using 3/16”

hex key.

3.Slide keyboard tray into

Paralink.

4.Replace screw and tighten.

5.Replace beauty cap.

Beauty cap

Screw

MOUNT MONITOR

ATTACH KEYBOARD TRAY

ADJUST BALL VESA

TENSION & HEIGHT

Use the slider knob to

loosen the slider to adjust

the height of the monitor

on the Paralink.

Adjust the pivot tension

of the ball by gently and

evenly tightening or

loosening the four screws

on the back of the ball

VESA.

Slider Knob

Pivot tension

adjustment

screws

ADJUST

PARALINK TILT

Adjust monitor to desired

position with ball VESA.

Tilt your monitor 50°

in any direction. Adjust

your monitor between

portrait and landscape

by rotating ball VESA.

Adjust monitor depth

by moving the paralink

forward or back then

tighting the depth

adjustment knob.

Depth

Adjustment

Knob

ATTACH VESA TO MONITOR

( PARALINK )

Attach VESA

to monitor

using four 4mm

screws in the

hardware bag.

TITAN ARM INSTALLATION

T2 ARM INSTALLATION - rev 04/22/2014 pjm

Page 3 of 3

MANAGE CABLES THROUGH ARM

• Using the Chrome 5mm hex key

provided, disassemble arm as shown

and lay out on a ﬂ at surface.

• Feed computer monitor cords and any

other cords through upper arm, lower

arm, wall mount and all bearings. When

feeding cords through arms, keep them

all to one side of bolts at arm joints.

• Pass cords through slots in monitor

mount base plate and re-attach monitor

mount to front arm.

• Once all cords have been passed

through the arms, reattach arms in the

same order as they were disassembled

using the Chrome 5mm hex key.

• Torque bolts down to 204 in/lbs (17 ft/lbs)

Cable slots in

monitor mount

base plate

NOTE: When measuring

for length of cords, be sure

to allow enough extra cord

to accommodate tilt and

rotation of monitor.

NOTE: CORDS CAN BE

DAMAGED IF JOINTS

ARE ROTATED MORE

THAN 360 DEGREES.

Bearing

Wall mount

Paralink

WARNING: When

disassembling the arms,

the Chrome 5mm hex

key must be used. If a

smaller hex key is used,

the bolt will strip.

ADJUST ROTATION LIMITS - WALL MOUNT

The rotation limits for

the arm are set by

placing the stop pins in

the hole corresponding

to where you want

the arm to stop. The

stop pin then collides

with the stop screw

under the wall mount

ear, stopping the arm.

The stop pins can be

removed and set by

hand.

Stop Pin

Rotation

Limiter

Ring

Stop Screw

(under wall ear)

Stop Pin

Andere ICW Rack & Stand Handbücher

ICW

ICW ELITE 5220 Bedienungsanleitung

ICW

ICW T2 Bedienungsanleitung

ICW

ICW ULTRA 180 ARM Bedienungsanleitung

ICW

ICW SINGLE ARM ELITE Bedienungsanleitung

ICW

ICW LTU-W3-A2 Bedienungsanleitung

ICW

ICW T2 Bedienungsanleitung

ICW

ICW Elite Bedienungsanleitung

ICW

ICW TITAN 2020 Bedienungsanleitung

ICW

ICW Elite ELP5220 Bedienungsanleitung

ICW

ICW ELITE DOUBLE ARM Bedienungsanleitung

ICW

ICW TITAN ELITE T2EQ-C8X5 Bedienungsanleitung

ICW

ICW ULTRA UL180 Bedienungsanleitung

ICW

ICW ULTRA 180 Bedienungsanleitung

ICW

ICW Elite Single Arm Bedienungsanleitung

ICW

ICW Elite Bedienungsanleitung

ICW

ICW TITAN ELITE T2E12P-WT2-KUB Bedienungsanleitung

ICW

ICW UL500 Bedienungsanleitung

ICW

ICW Titan Elite Bedienungsanleitung

ICW

ICW ELITE 5220 Bedienungsanleitung

ICW

ICW Elite Bedienungsanleitung

ICW

ICW GX170 Bedienungsanleitung

ICW

ICW UL90 Bedienungsanleitung

ICW

ICW PRO SLIDE Bedienungsanleitung

ICW

ICW ULTRA Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung