IFM Electronic SI0562 Bedienungsanleitung

Operating instructions

Flow monitors

SI5006

SI0562

704194 / 04 02 / 2022

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��4

3�1 Application area ��4

3�2 Operating principle flow monitoring ��4

4 Installation��5

4�1 Installation location ��5

4�2 Sources of interference in the pipe system ��6

4�3 Mounting operation��6

5 Electrical connection��7

6 Operating and display elements ��8

7 Set-up and settings for water��9

7�1 Change the switch point (optional) ��9

7�2 High flow adjustment (optional) ��10

8 Additional settings (optional)�� 11

8�1 Low flow adjustment �� 11

8�2 Configure the switching output �� 11

8�3 Restore the factory setting (reset) �� 11

8�4 Lock / unlock the unit�� 11

9 Error during adjustment ��12

10 Operation��13

11 Maintenance ��13

12 Technical data��13

1 Preliminary note

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of buttons, switches or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference�

2 Safety instructions

• The device described is a subcomponent for integration into a system�

- The manufacturer is responsible for the safety of the system�

- The system manufacturer undertakes to perform a risk assessment and to

create a documentation in accordance with legal and normative requirements

to be provided to the operator and user of the system� This documentation

must contain all necessary information and safety instructions for the opera-

tor, the user and, if applicable, for any service personnel authorised by the

manufacturer of the system�

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and environ-

mental conditions without any restrictions�

• Only use the product for its intended purpose (→ Functions and features).

• Only use the product for permissible media (→ Technical data).

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the unit

must be carried out by qualified personnel authorised by the machine operator�

• Protect units and cables against damage�

3 Functions and features

This is a class A product� This product may cause radio interference in

domestic areas�

►If required, take appropriate EMC screening measures�

3.1 Application area

The unit monitors the flow of liquid and gaseous media�

3.2 Operating principle flow monitoring

• The unit detects the flow speed to the calorimetric measuring principle and

switches the output:

- output closed if medium is flowing / output open if no medium is flowing�

This applies to the unit on delivery: output = normally open� In case of need you

can change the output to normally closed (→ 8.2). It then applies: output open

if medium is flowing�

• If the flow speed increases, the switching status changes when the switch point

is reached�

• If the flow speed falls again, the switching status changes if the value "SP

minus hysteresis" is reached�

The hysteresis changes with the flow speed and it is essentially influenced by

the set monitoring range�

It is 2��5 cm/s for the setting 5��100 cm/s (= factory setting), it increases with

higher flow speeds�

• The typical response time of the unit is 1��10 s� It can be influenced by the

setting of the switch point:

- Low switch point = quick reaction with rising flow�

- High switch point = quick reaction with falling flow�

4 Installation

Using process adapters the unit can be adapted to different process connections�

• Adapters have to be ordered separately as accessories�

A correct fit of the unit and ingress resistance of the connection are only en-

sured using ifm adapters�

• For small flow rates ifm adapter blocks are available�

4.1 Installation location

General



• The sensor tip is to be completely sur-

rounded by the medium�

• Insertion depth of the sensor: minimum

12 mm�

Recommended

• For horizontal pipes: mounting from

the side�

• For vertical pipes: mounting in the rising

pipe�

Conditional

• Horizontal pipe /mounting from the bot-

tom: if the pipe is free from build-up�

• Horizontal pipe /mounting from the

top: if the pipe is completely filled with

medium�

To avoid

• The sensor tip must not be in contact

with the pipe wall�

• Do not mount in downpipes that are

open at the bottom!

4.2 Sources of interference in the pipe system

Components integrated in the pipes, bends, valves, reductions, etc� lead to turbu-

lence of the medium� This affects the function of the unit�

Recommendation: Adhere to the distances between sensor and sources of inter-

ference:



 











 









D = pipe diameter; S = sources of interference

4.3 Mounting operation

►Ensure that the system is free of pressure during installation�

►Ensure that no media can leak at the mounting location during installa-

tion�

  









►Grease the threads of the process connection (1), adapter (2) and nut (3)�

Note: The sensor tip (A) must not be in contact with grease�

►Screw the suitable adapter into the process connection�

►Place the flow monitor onto the adapter and tighten the nut� Tightening torque

25 Nm� Ensure that the unit is correctly oriented�

5 Electrical connection

• The unit must be connected by a qualified electrician�

• The national and international regulations for the installation of electrical equip-

ment must be adhered to�

• The unit complies with overvoltage category II�

• Caution: For the output circuit the same protective measures as for the supply

circuit must be taken�

• Insert a miniature fuse according to IEC60127-2 Sheet 1 (≤ 5 A fast acting).

• The permissible potential difference between supply and output circuit is max�

300 V�

• The metal parts of the housing must be properly grounded� For this, you can,

for example, attach a grounding clip to the connector and ensure the grounding

using a potential equalisation cable�

• The design of the unit corresponds to protection class II�

• Due to the integrated EMC filters, leakage currents of typ� < 0�5 mA can flow

via the potential equalisation to the earth potential�

• If several units are used in parallel, take into account that the leakage currents

add�

• The applicable standards must be adhered to�

►Disconnect power�

►Connect the unit as follows:

A: supply circuit; B: output circuit

: safe separation

Core colours of ifm sockets:

1 = BN (brown), 2 = BU (blue), 4 = BK (black), 5 = WH (white)

For information about available sockets go to www�ifm�com�

6 Operating and display elements

 









 

1: Operation display

• The green LEDs indicate the current flow (the LEDs 0 to 9 represent the range between

no flow and maximum flow)�

• A lighting LED indicates the position of the switch point (orange = output closed, red =

output open)�

2, 3: Setting buttons for adjustment and configuration

7 Set-up and settings for water

(For media other than water → 8.1: Low flow adjustment).

►Switch on the supply voltage�

> All LEDs light and go out again step by step� During this time the output is

closed (if configured as normally open)� The unit is in the operating mode�

►Let the normal flow circulate in the installation�

►Check the display and determine further actions�

 





The factory setting is suitable for the applica-

tion�

►No further settings are required�

 





Your normal flow is below the representation

range of the display�

2 setting options:

► Change the switch point (→ 7.1).

► Carry out high flow adjustment (→ 7.2).

 





Your normal flow exceeds the representation

range of the display (LED 9 flashes)�

► Carry out high flow adjustment (→ 7.2).

You can restore the factory setting any time. (→ 8.3).

7.1 Change the switch point (optional)

For the factory setting the switch point is at LED 7� A change makes sense in the

folowing cases:

• the display shows example 2�

• the flow fluctuates much or pulsates�

• a faster response time of the unit is requested (low switch point = fast response

with rising flow, high switch point = fast response with falling flow)�

►Briefly press the pushbutton or �

> The switch point LED flashes�

►Press the pushbutton or as often as required� Each press of the push-

button shifts the LED by one position in the indicated direction�

Note: If no pushbutton is pressed for 2 s, the unit returns to the operating mode

with the newly set value�

7.2 High flow adjustment (optional)

The unit determines the existing flow as normal flow and adapts the display repre-

sentation (all LEDs except the switch point LED light green)�

►Let the normal flow circulate in the installation�

►Press the pushbutton and keep it pressed�

> LED 9 lights, after approx� 5 s it flashes�

►Release the pushbutton�

The unit is now adapted to your flow conditions� It passes into the operating mode,

the display should now show example 1�

Note: The adjustment affects the switch point: It is increased proportionally (maxi-

mum up to LED 7)�

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Electronic Messgerät Handbücher

IFM Electronic

IFM Electronic efector300 SD6000 Bedienungsanleitung

IFM Electronic

IFM Electronic SI5006 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 300 SI0556 Bedienungsanleitung

IFM Electronic

IFM Electronic SM9000 Bedienungsanleitung

IFM Electronic

IFM Electronic OW Bedienungsanleitung

IFM Electronic

IFM Electronic PG24 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SD6050 Bedienungsanleitung

IFM Electronic

IFM Electronic SD0550 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SD2000 Bedienungsanleitung

IFM Electronic

IFM Electronic SD6050 Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SD6101 Bedienungsanleitung

IFM Electronic

IFM Electronic SI5007 Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SD6000 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OJ50 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SD2001 Bedienungsanleitung

IFM Electronic

IFM Electronic SI0551 Bedienungsanleitung

IFM Electronic

IFM Electronic PK5520 Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SM0510 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SL0106 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 300 SA3010 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SI0508 Bedienungsanleitung

IFM Electronic

IFM Electronic efector300 SD6001 Bedienungsanleitung

IFM Electronic

IFM Electronic SD8000 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 160 LK1222 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung