IFM AS-i CompactModule M8 Bedienungsanleitung
Operating instructions
AS-i CompactModule M8
AC2490
80272461/00 03/2018
UK
UK
2
1 Preliminary note
Technical data, approvals, accessories and further information at
www.ifm.com.
2 Safety instructions
• Read this document before setting up the product and keep it during the entire
service life.
• The product must be suitable for the corresponding applications and
environmental conditions without any restrictions.
• Only use the product for its intended purpose (→ Functions and features).
• If the operating instructions or the technical data are not adhered to, personal
injury and/or damage to property may occur.
• The manufacturer assumes no liability or warranty for any consequences
caused by tampering with the product or incorrect use by the operator.
• Installation, electrical connection, set-up, operation and maintenance of the
product must be carried out by qualified personnel authorised by the machine
operator.
• The plant operator is responsible for the safety of the plant in which the device
is installed.
• If the device is not used as intended by the manufacturer, the protection
supported by the device may be impaired.
• Protect units and cables against damage.
2.1 Symbols used
► Instructions
→ Cross-reference
Important note
Non-compliance may result in malfunction or interference.
Information
Supplementary note.
3
UK
3 Functions and features
• Maximum number of modules per master: 62
• AS-Interface version 3.0, downward compatible
• 4 inputs / 4 outputs / AS-i profile S-7.A.7 / extended addressing mode: yes
• The unit can only be operated in conjunction with a version 3.0 master (master
profile M4).
4 Installation
► Disconnect the system from power before installation.
► For installation choose a flat mounting surface.
The entire bottom of the module must lie flat on the mounting surface.
► Fix the module onto the mounting surface using M4 screws and washers.
5 Electrical connection
► Disconnect the installation from power and connect the unit.
To ensure the protection rating:
► Connect the plugs of the sensors to the M8 sockets.
► Tighten firmly, recommended tightening torque 0.3...0.5 Nm.
► Cover the sockets that are not in use with the enclosed protective caps.
5.1 Pin connection
Socket M12
1: AS-i +
2: AUX -
3: AS-i -
4: AUX +
4
12
3
Input M8
1: sensor supply +
3: sensor supply -
4: data input
Output M8
3: external voltage E-
4: switching output
4
Parameter bit Designation Description
P1 Periphery fault 1 peripheral fault indication active
0 peripheral fault indication not active
6 Addressing
► Addressing the unit via the M12 connector; the address is set to 0 at the
factory.
Addressing unit AC1154
Wiring of the addressing socket
51
34
2
1: SFC-i + / 2: TTL → / 3: SFC-i -
4: TTL ← / 5: + 5 V
7 Operating and display elements
M12x1
M8x1
LED
PWR ⁄ FAULT
LED
AUX
LEDs -x
LEDs O-x
8 Operation
LED I-x / O-x yellow: input / output switched
LED PWR green: AS-i voltage supply OK
LED AUX green: External voltage supply (AUX) o.k.
LED FAULT red is lit: AS-i communication error, slave does not participate
in the "normal" exchange of data, e.g. slave address
0.
LED FAULT red flashes: Periphery fault, e.g. sensor supply overloaded or
shorted, is signalled to the AS-i master
(version 2.1 or higher).
Inhaltsverzeichnis
Andere IFM Messgerät Handbücher
IFM
IFM ZZ0600 Handbuch
IFM
IFM SI0558 Bedienungsanleitung
IFM
IFM SL010 Series Bedienungsanleitung
IFM
IFM SD1540 Bedienungsanleitung
IFM
IFM efector300 SI0102 Bedienungsanleitung
IFM
IFM SDG082 Bedienungsanleitung
IFM
IFM efector 300 SD2001 Bedienungsanleitung
IFM
IFM efector 300 SI0509 Bedienungsanleitung
IFM
IFM SM6x04 Bedienungsanleitung
IFM
IFM Efector 300 SL5204 Bedienungsanleitung
IFM
IFM SU2020 Bedienungsanleitung
IFM
IFM SM2 00 Series Bedienungsanleitung
IFM
IFM SM2x00 Bedienungsanleitung
IFM
IFM SI0555 Bedienungsanleitung
IFM
IFM efector 300 SI0558 Bedienungsanleitung
IFM
IFM SI0550 Bedienungsanleitung
IFM
IFM efector300 SA3000 Bedienungsanleitung
IFM
IFM efector 300 SI5010 Bedienungsanleitung
IFM
IFM SI6600 Bedienungsanleitung
IFM
IFM DI604A Bedienungsanleitung
