IFM Efector300 SI6000 Bedienungsanleitung

Operating instructions

Flow monitors

SI6000

SI6100

SI6200

706053/00 06/2011

Contents

1 Safety instructions �� 3

2 Functions and features�� 4

2�1 Application area �� 4

2�2 Operating principle flow monitoring �� 4

3 Installation �� 5

3�1 Installation location�� 5

3�2 Sources of interference in the pipe system �� 6

3�3� Mounting operation�� 6

4 Electrical connection�� 8

5 Operating and display elements�� 8

6 Set-up and settings for water�� 9

6�1 Change the switch point (optional) �� 9

6�2 High flow adjustment (optional) �� 10

7 Additional settings (optional)�� 10

7�1 Low flow adjustment�� 10

7�2 Configure the switching output �� 10

7�3 Restore the factory setting (reset) �� 11

7�4 Lock / unlock the unit�� 11

8 Error during adjustment�� 11

9 Operation�� 12

10 Maintenance�� 12

11 Scale drawing �� 13

12 Technical data�� 16

Preliminary note

• Aninstructionisindicatedby“►”:

Example:►Checkwhethertheunitoperatescorrectly.

• Areactiontotheactionisindicatedby">":

Example:>LED9lights.

1 Safety instructions

• Please read the product description prior to set-up of the unit� Ensure that the

product is suitable for your application without any restrictions�

• Improper or non-intended use may lead to malfunctions of the unit or to un-

wanted effects in your application�

• That is why installation, electrical connection, set-up, operation and mainte-

nance of the unit must only be carried out by qualified personnel authorised by

the machine operator�

ForthescopeofvaliditycULus:

The device shall be supplied from an isolating transformer having a secondary

Listed fuse rated as noted in the following table�

Overcurrent protection

Control-circuit wire size Maximum protective device rating

Ampere

AWG (mm2)

26 (0�13) 1

24 (0�20) 2

22 (0�32) 3

20 (0�52) 5

18 (0�82) 7

16 (1�3) 10

2 Functions and features

2.1 Application area

The unit monitors the flow of liquid and gaseous media�

2.2 Operating principle flow monitoring

• The unit detects the flow speed to the calorimetric measuring principle and

switchestheoutput:

- output closed if medium is flowing / output open if no medium is flowing�

Thisappliestotheunitondelivery:output=normallyopen.Incaseofneedyou

canchangetheoutputtonormallyclosed(→7.2).Itthenapplies:outputopen

if medium is flowing�

• If the flow speed increases, the switching status changes when the switch point

is reached�

• If the flow speed falls again, the switching status changes if the value "SP

minus hysteresis" is reached�

The hysteresis changes with the flow speed and it is essentially influenced by

the set monitoring range�

Itis2...5cm/sforthesetting5...100cm/s(=factorysetting),itincreaseswith

higher flow speeds�

• The typical response time of the unit is 1��10 s� It can be influenced by the

settingoftheswitchpoint:

- Lowswitchpoint=quickreactionwithrisingflow.

- Highswitchpoint=quickreactionwithfallingflow.

3 Installation

Using process adapters the unit can be adapted to different process connections�

• Adapters have to be ordered separately as accessories�

A correct fit of the unit and ingress resistance of the connection are only

ensuredusingifmadapters.Mountingoftheadapter→3.3.

3.1 Installation location

General



•The sensor tip is to be completely

surrounded by the medium�

•Insertiondepthofthesensor:

minimum 12 mm�

Recommended

•Forhorizontalpipes:mountingfrom

the side�

•Forverticalpipes:mountinginthe

rising pipe�

Conditional

•Horizontal pipe /mounting from

thebottom:ifthepipeisfreefrom

build-up�

•Horizontal pipe /mounting from the

top:ifthepipeiscompletelyfilled

with medium�

To avoid

•The sensor tip must not be in

contact with the pipe wall�

•Donotmountindownpipesthatare

open at the bottom!

3.2 Sources of interference in the pipe system

Components integrated in the pipes, bends, valves, reductions, etc� lead to turbu-

lence of the medium� This affects the function of the unit�

Recommendation:Adheretothedistancesbetweensensorandsourcesof

interference:



 











 









D=pipediameter;S=sourcesofinterference

3.3. Mounting operation

►Ensure that the system is free of pressure during installation�

►Ensure that no media can leak at the mounting location during installation�

















G:grease

► Mounttheadapter(D)ontheunit(A).

►Fix the unit + adapter to the process connection by means of a coupling nut, a

clamp flange or the like (B)�

Ifitisnotpossibletoslidethefixingelement(B)downoverthetopoftheunit:

Slide it up over the bottom of the sensor before the adapter is mounted�

Mounting the adapter

►Slightly grease the threads and sealing areas of the sensor and adapter with

lubricating paste�

The paste must be suitable and approved for the application and compatible

with the elastomers used�

Recommendation:KlüberpasteUH184-201withUSDA-H1approvalforthe

food industry�

►Make sure that the O-ring (C) is correctly positioned�

►Screw the unit into the adapter until it is hand-tight� Avoid mechanical influence

on the sealing areas�

►Clamp unit and adapter into a clamping device (E)� The sealing areas (F) must

not be damaged�

►Tighten the unit slightly using a spanner until you can feel the end stop (this

correspondstoamaximumtighteningtorqueof25Nm).NOTE:Furthertight-

ening may affect the sealing effect

NOTE:Aguaranteeforlong-termstableandmaintenance-freefittingwithnobug

traps in the hygienic sealing of the metal seal (Aseptoflex connection) is only valid

for once-only mounting�

Mounting by means of a welding adapter

►Weld adapter in the pipe or the tank�

►After the unit has cooled down insert and tighten it� Follow the instructions

included with the adapter�

4 Electrical connection

The unit must be connected by a qualified electrician�

The national and international regulations for the installation of electrical

equipment must be adhered to�

Voltage supply to EN 50178, SELV, PELV�

► Disconnectpower.

► Connecttheunitasfollows:





















Corecoloursofifmsockets:

1=BN(brown),3=BU(blue),4=BK(black)

5 Operating and display elements

 









 

1: Operation display

•ThegreenLEDsindicatethecurrentflow(theLEDs0to9representtherangebetween

no flow and maximum flow)�

•AlightingLEDindicatesthepositionoftheswitchpoint(orange=outputclosed,red=

output open)�

2, 3: Setting buttons for adjustment and configuration

6 Set-up and settings for water

(Formediaotherthanwater→7.1:Lowflowadjustment).

►Switch on the supply voltage�

> AllLEDslightandgooutagainstepbystep.Duringthistimetheoutputis

closed (if configured as normally open)� The unit is in the operating mode�

►Let the normal flow circulate in the installation�

►Check the display and determine further actions�

 





The factory setting is suitable for the applica-

tion�

►No further settings are required�

 





Your normal flow is below the representation

range of the display�

2settingoptions:

► Changetheswitchpoint(→6.1).

► Carryouthighflowadjustment(→6.2).

 





Your normal flow exceeds the representation

rangeofthedisplay(LED9flashes).

► Carryouthighflowadjustment(→6.2).

Youcanrestorethefactorysettinganytime.(→7.3).

6.1 Change the switch point (optional)

ForthefactorysettingtheswitchpointisatLED7.Achangemakessenseif:

• the display shows example 2�

• the flow fluctuates much or pulsates�

• ifafasterresponsetimeoftheunitisrequested(lowswitchpoint=fastre-

sponsewithrisingflow,highswitchpoint=fastresponsewithfallingflow).

►Briefly press the pushbutton or �

> TheswitchpointLEDflashes.

►Press the pushbutton or as often as required� Each press of the push-

buttonshiftstheLEDbyonepositionintheindicateddirection.

Note:Ifnopushbuttonispressedfor2s,theunitreturnstotheoperatingmode

with the newly set value�

6.2 High flow adjustment (optional)

The unit determines the existing flow as normal flow and adapts the display repre-

sentation(allLEDsexcepttheswitchpointLEDlightgreen).

►Let the normal flow circulate in the installation�

►Press the pushbutton and keep it pressed�

> LED9lights,afterapprox.5sitflashes.

►Release the pushbutton�

The unit is now adapted to your flow conditions� It passes into the operating mode,

the display should now show example 1�

Note:Theadjustmentaffectstheswitchpoint:Itisincreasedproportionally

(maximumuptoLED7).

7 Additional settings (optional)

7.1 Low flow adjustment

If the unit is used in media other than water, you should additionally adapt the unit

to the minimum flow�

Note:Thefollowingadjustmentmustonlybecarriedoutafterthehighflowadjust-

ment�

►Let the minimum flow circulate in the installation or ensure flow standstill�

►Press the pushbutton and keep it pressed�

> LED0lights,afterapprox.5sitflashes.

►Release the pushbutton� The unit adopts the new value and passes into the

operating mode�

7.2 Configure the switching output

The unit is delivered as normally open� In case of need you can change the output

tonormallyclosed:

►Press the pushbutton for at least 15 s�

> LED0lights,afterapprox.5sitflashes.

> After10sthecurrentsettingisdisplayed:LEDs5...9lightorange(=output

normally open)�

> Afterapprox.15sLEDs0...4flashorange.

►Release the pushbutton� The output is changed to normally closed operation�

For a new changeover repeat the operation�

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Messgerät Handbücher

IFM

IFM efector300 SA3000 Bedienungsanleitung

IFM

IFM SM4x00 Bedienungsanleitung

IFM

IFM SDG070 Bedienungsanleitung

IFM

IFM ZZ0600 Handbuch

IFM

IFM DD111S Bedienungsanleitung

IFM

IFM OY51 Bedienungsanleitung

IFM

IFM SM9x04 Series Bedienungsanleitung

IFM

IFM efector300 SD0523 Bedienungsanleitung

IFM

IFM SU9020 Bedienungsanleitung

IFM

IFM efector 300 SI0558 Bedienungsanleitung

IFM

IFM SM2x00 Bedienungsanleitung

IFM

IFM SD1540 Bedienungsanleitung

IFM

IFM Efector 300 SL5204 Bedienungsanleitung

IFM

IFM efector 300 SI5010 Bedienungsanleitung

IFM

IFM PG243 Bedienungsanleitung

IFM

IFM LW2720 Bedienungsanleitung

IFM

IFM PK6730 Bedienungsanleitung

IFM

IFM DI5029 Bedienungsanleitung

IFM

IFM efector300 SI0102 Bedienungsanleitung

IFM

IFM ZZ0600 Handbuch

IFM

IFM SV0527 Bedienungsanleitung

IFM

IFM SI0551 Bedienungsanleitung

IFM

IFM SDG 50 Series Bedienungsanleitung

IFM

IFM SM2 00 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

IFM efector300 SI6000 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken