IFM DV2120 Bedienungsanleitung

Operating instructions

1-segment signal lamp

DV2120

DV2121

DV2130

DV2131

80284259 / 00 12 / 2019

Original Scale Drawing (MTD)

EPS Source

Product Scale Drawing

Frame Size: 80 mm x 27 mm

P_MZ_e200_0102

92,3

75,5

M30x 1,5

36 5

M12x1

LEDs

Contents

1 Preliminary note��3

1�1 Symbols used ��3

1�2 Warnings used��3

2 Safety instructions ��4

3 Functions and features ��5

3�1 IO-Link ��5

3�1�1 General information ��5

3�1�2 Device-specific information��5

4 Installation��6

5 Electrical connection��7

5�1 IO-Link connection��7

5�2 Pin connection ��7

5�2�1 IO-Link mode ��7

5�2�2 Standard mode ��7

6 Operating and display elements ��8

7 Operation��8

7�1 IO-Link ��8

7�1�1 General��8

7�1�2 On/off mode��9

7�1�3 RGB mode��9

7�2 Operation with digital IOs ��12

7�2�1 General��12

7�2�2 SIO mode in on/off mode��12

7�2�3 SIO mode in RGB mode��13

8 Parameter setting ��13

9 Scale drawing ��14

9�1 DV212x��14

9�2 DV213x��14

10 Technical data��15

10�1 IO-Link device��15

11 Maintenance, repair and disposal ��16

1 Preliminary note

Technical data, approvals, accessories and further information at

www�ifm�com�

1.1 Symbols used

►Instruction

> Reaction, result

[…] Designation of keys, buttons or indications

→Cross-reference

Important note

Non-compliance may result in malfunction or interference�

Information

Supplementary note�

1.2 Warnings used

WARNING!

Warning of serious personal injury�

Death or serious irreversible injuries may result�

CAUTION!

Warning of personal injury�

Slight reversible injuries may result�

NOTE!

Warning of damage to property

11�1 Cleaning the housing surface ��16

12 Approvals/standards ��16

2 Safety instructions

• The device described is a subcomponent for integration into a system�

The manufacturer is responsible for the safety of the system� The system

manufacturer undertakes to perform a risk assessment and to create a

documentation in accordance with legal and normative requirements to be

provided to the operator and user of the system� This documentation must

contain all necessary information and safety instructions for the operator,

the user and, if applicable, for any service personnel authorised by the

manufacturer of the system�

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and

environmental conditions without any restrictions�

• Only use the product for its intended purpose (→ 3 Functions and features)�

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• In case of malfunctions of the unit, please contact the manufacturer� Tampering

with the unit is not allowed�

• Installation, electrical connection, set-up, programming, configuration, operation

and maintenance of the product must be carried out by personnel qualified and

authorised for the respective activity�

• Protect units and cables against damage�

• If the device is used in a way that is not allowed by the manufacturer the

protection provided by the device may be affected�

3 Functions and features

The unit is used for the visual display of machine conditions� The versions DV2130

and DV2131 additionally have a buzzer for acoustic signalling� The versions

DV2121 and DV2131 additionally have a feedback button�

The LED segment and the audible warning device can be switched on and off

individually�

►The device is intended for indoor use only�

Observe the operating conditions (→ 10 Technical data)�

►The unit must not be used for safety-related applications such as

access control�

The units can be controlled and configured via the standardised IO-Link interface�

3.1 IO-Link

3.1.1 General information

This unit has an IO-Link communication interface which enables direct access to

process and diagnostic data� In addition it is possible to set the parameters of the

unit while it is in operation� Operation of the unit via an IO-Link interface requires

an IO-Link capable module (IO-Link master).

3.1.2 Device-specific information

With a PC, suitable IO-Link software and an IO-Link adapter cable, communication

is possible while the system is not in operation� The IODDs necessary for the

configuration of the unit, detailed information about process data structure,

diagnostic information, parameter addresses and the necessary information about

the required IO-Link hardware and software can be found at www�ifm�com�

4 Installation

►Disconnect power before installation�

►For installation choose a flat mounting surface�

Maximum thickness of the mounting surface: 10 mm

Installation example:

►Create a mounting section Ø 31 mm

►Only mount the unit in upright position using the supplied M30 nut�

Tightening torque 4�5 Nm�

Special accessories are available to allow mounting the unit using a

mounting tube or pole�

Integrated seals at the bottom of the unit and an O-ring on the cover

prevent penetration of humidity�

More information about available accessories at www�ifm�com

5 Electrical connection

The device must be connected by a qualified electrician�

The national and international regulations for the installation of electrical

equipment must be adhered to�

Voltage supply according to SELV, PELV

For use in USA and Canada: voltage supply to class 2

►Disconnect power�

►Connect the cable with the M12 connector of the unit�

Tightening torque max� 0�4 Nm�

Observe the maximum tightening torque of the connection cable�

5.1 IO-Link connection

The IO-Link port must be connected according to the IO-Link specification�

5.2 Pin connection

5.2.1 IO-Link mode

M12 connector, 5 poles, A-coded

(4 x 0.34 mm² / AWG 22)

1: V+

2: not connected

3: 0V

4: IO-Link

5: not connected

2 1

5.2.2 Standard mode

M12 connector, 5 poles, A-coded

(4 x 0.34 mm² / AWG 22)

1: LED-a (RGB red)

2: LED-b (RGB green)

3: GND

4: Feedback button (only DV21x1) /

Buzzer (only DV213x)

5: LED-c (RGB blue)

2 1

6 Operating and display elements

Original Scale Drawing (MTD)

EPS Source

Product Scale Drawing

Frame Size: 80 mm x 27 mm

P_MZ_e200_0102

92,3

75,5

M30x 1,5

36 5

M12x1

LEDs

1: Feedback button (only DV21x1)

2: LED segment 1 with 3 RGB LEDs

3: Buzzer (only DV213x)

7 Operation

7.1 IO-Link

7.1.1 General

Connect the unit to an IO-Link master (A port) using a 5-pole connection cable.

The controller switches the LED segment on and off in the configured colours

according to the set parameters�

Via the parameter "Operating mode" the following modes can be set:

• On/off mode

• RGB mode

Versions with feedback button: The status of the feedback button can be read

(both in on/off mode and in RGB mode).

7 6 5 4 3 2 1 0 PDin

Device fault information Byte 0

Feedback

button

Byte 1

7.1.2 On/off mode

While the unit is operating, the controller switches the LED segment and the

buzzer (DV213x) on and off (PDout, cyclical data communication). The signalling

corresponds to the parameters previously defined for the LED segment and the

buzzer�

Via acyclic parameter setting, the following properties can be set for the LED

segment:

• Colour (red, green, orange, blue, violet, turquoise, white, yellow, off)

• Frequency (permanently on, low flash rate slow/medium/fast, high flash rate

slow/medium/fast)

• Brightness (0...100 %)

For the models with an acoustic signal device the audibility of the buzzer can be

set�

7 6 5 4 3 2 1 0 PDOut

LED-c LED-b LED-a Byte 0

Buzzer Byte 1

7.1.3 RGB mode

While the unit is operating, the controller switches the LED segment and the

buzzer (only DV213x) on and off and determines the corresponding properties

(PDout, cyclical data communication).

In this operating mode, 8 different acoustic signals are available for the buzzer�

7 6 5 4 3 2 1 0 PDOut

LED properties Seg� 1 =

yellow

Seg� 1 =

red

Seg� 1 =

green

Seg� 1

blue

Byte 0

Buzzer sound (buzzer style

1...8)

Buzzer Byte 1

The properties of the LED segment are defined as follows:

Byte 0

Bit 3

Byte 0

Bit 2

Byte 0

Bit 1

Byte 0

Bit 0

Colour

0 0 0 0 off

0 0 0 1 red

0 0 1 0 green

0 0 1 1 orange

0 1 0 0 blue

0 1 0 1 violet

0 1 1 0 turquoise

0 1 1 1 white

1 0 0 0 yellow

Byte 0

Bit 6

Byte 0

Bit 5

Byte 0

Bit 4

Frequency

0 0 0 permanently on

0 0 1 low flash rate slow

0 1 0 low flash rate medium

0 1 1 low flash rate fast

1 0 0 high flash rate slow

1 0 1 high flash rate medium

1 1 0 high flash rate fast

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Außenleuchte Handbücher

IFM

IFM O2D93 Series Bedienungsanleitung

IFM

IFM DV15 Series Bedienungsanleitung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung