Innovative MAX Bedienungsanleitung

MAX ROLL BENCH ASSEMBLY INSTALLATION

Complete Instructional Guide

! Attention!

Before starting the assembly of your benching

system, check floor surface to ensure a level starting

point. If your floors are damaged, heavily sloped or

contain obstacles, you may have issues with proper

bench setup. These issues should have been noted

during the Floor Layout/Quoting phase and may

need custom designed components to correct these

issues.

Innovative Growers Equipment, Inc. is not liable for

the replacement of parts and components.

Before starting the assembly of your benching

system, ensure that Bench Assembly Layout and

Staal & Plast tray gluing instruction packets are

available prior to starting installation.

If not, please contact Innovative Growers Equipment,

Inc. contact information located at the end of this

instruction packet.

7/16” & 3/4” WRENCHS & SOCKETS

TAPE MEASURE

TOOLS NEEDED FOR INSTALLATION

POWER DRILL/IMPACT

W/BITS & NUT DRIVERS

CAULK GUN

POP RIVET GUN

*Pneumatic Rivet Gun Suggested

2+ People Needed

for installation.

Estimated Time:

1-2 hours depending on

bench length.

2’ LEVEL

HAMMER DRILL W/

5/32 MASONRY BIT

UTILITY KNIFE

MALLET

VACUUM/BLOWOUT BULB

PARTS NEEDED FOR INSTALLATION

Confirm all parts are present before starting assembly. If parts are

missing or damaged refer to contact information on last page.

* Parts are only applicable if Bench Assembly Layout calls for

multiple parts.

Group

Part

Description

Refer to Bench

Assembly Layout/

Parts List for Lengths,

Dimensions and

Quantities

◼A1: Leg Units

◼A2: Load

Bearing Plug

◼A3: Stringer

Pipe 1” x 1”

◼*A4: Additional

Stringer Pipe 1”

x 1”

◼A5: Stringer

Insert .813” x 5”

Long

◼A6: Square to

Square Clamp

A3&4

◼B1: Anti-Tip

System

◼B2: Plain

Header Unit

◼C1: Rolling

pipe

Swedged/

Crimped End

◼C2: Rolling

Pipe Plain End

◼C3: Bench

Cross Bar

◼D1: Bench

Corner

◼D2: Aluminum

Side Rail –Longer

with 3/2 hole combo

on ends

◼*D3: Additional

Aluminum Side

Rail

◼D4: Aluminum

End Rail –Shorter

with 3/3 hole combo

on ends

◼D5: Joiner

Plates

◼D6: End Frame

(For 5’ wide or wider

benches only)

D2-D3

◼E1: End Tray

W/ Well

◼E2: Middle

Tray

◼E3: Filler Tray

◼E4: End Tray

No Well

◼F1: Pop-Rivet

◼F2: Self-

Tapping Screw

◼F3: ¼-20 Hex

Nut

◼F4: ¼-20 x .75”

Hex Screw

◼F5: ½” Flat

Washer

◼F6: Tap Con

3/16 x 1-3/4”

◼F7: Safety

Chain

◼F8: Angle

Bracket

STEP #1

Lay out Leg Units and Stringer Pipe.

◼Before (A1) Leg Units are removed from bundle, install (A2) Load Bearing Plugs into

uncrimped ends.

◼(A2) Load Bearing Plugs to be inserted in non-crimped bottom two openings. Shown

Fig. 1a.

◼Note: Mallet may be used to help seat

(A2) Load Bearing Plugs onto (A1) Legs Units

1a.

Inhaltsverzeichnis

Andere Innovative Rack & Stand Handbücher

Innovative

Innovative EVO 5900 Bedienungsanleitung

Innovative

Innovative 9138 Bedienungsanleitung

Innovative

Innovative Winston Lift Single Bedienungsanleitung

Innovative

Innovative 8520 Bedienungsanleitung

Innovative

Innovative UltraRack URPS Bedienungsanleitung

Innovative

Innovative WINSTON-E Series Bedienungsanleitung

Innovative

Innovative LCD Monitor Arm 9103 Bedienungsanleitung

Innovative

Innovative 7000 Bedienungsanleitung

Innovative

Innovative Ella Bedienungsanleitung

Innovative

Innovative PTS-04-ISC250 Bedienungsanleitung

Innovative

Innovative 9400 Bedienungsanleitung

Innovative

Innovative 8521 Bedienungsanleitung

Innovative

Innovative PTS-04-M400/MX915 Bedienungsanleitung

Innovative

Innovative 9120 Bedienungsanleitung

Innovative

Innovative PTS-04-LANE Bedienungsanleitung

Innovative

Innovative Winston Lift Single Bedienungsanleitung

Innovative

Innovative Busby 8451 Bedienungsanleitung

Innovative

Innovative 8408 Bedienungsanleitung

Innovative

Innovative 5501 Bedienungsanleitung

Innovative

Innovative 9035 CRT Installationsanleitung

Innovative

Innovative 7020 Bedienungsanleitung

Innovative

Innovative Ella Bedienungsanleitung

Innovative

Innovative STAXX Series Bedienungsanleitung

Innovative

Innovative 9136 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung