Inspur NF3120M5 Bedienungsanleitung

V01502G000000000

Warnings!

15kg

30kg

50kg

● During the installation process, please do not block the vents on the server, especially the

vents on the front and rear of the server.

● Please remove the protective film from the server surface before using.

● Please leave a minimum of 15cm clearance on the front and rear sides of the server for

proper ventilation.

● Please install air baffles in place prior to device installation, to make sure that the server can

get enough air flow, and to avoid air turbulence in the server room.

● Servers are high-power electrical appliances, and they should be installed into dedicated

cabinets with vents or professional water-cooled cabinets, to prevent system failures caused

by overheating.

● If it needs to install more than one device, please load them from the bottom to the top, and

load the heaviest items first.

● Please note the cabinet’s load-bearing capacity, power supply capacity and heat

dissipation capacity, be sure not to install devices beyond the cabinet’s threshold capacity.

● For the convenience of using the front and rear ports of the server and cabling, leave a

minimum clearance of 70mm between the front end of the server and the inner side of the

cabinet’s front door, and 150mm between the rear end of the server and the inner side of the

cabinet’s rear door.

If the device is more than 15kg, at least 2 people are needed.

If the device is more than 30kg, at least 3 people are needed.

If the device is more than 50kg, at least 4 people are needed.

The cabinet, chassis or guide rails may cause serious scratches,

please be careful while handling.

When installing new servers into the cabinet in use, please be

aware of electric shock.

V1.0

Rack-Mounted Server

Installation Guide

Please keep this document for future reference.

Rack-Mounted Server Installation Guide V1.0

Pull the middle rails fully extended in lock position. Lift the server, align the inner

rails with the middles, and push the server slowly until it hits a stop.

Installing the server

Position the rail on the rack. Fix the rear bracket first, and insert the guide pins

into the rack holes.

Open the latch on the front bracket. Align the guide pins with the rack holes,

and insert the pins into the holes. Release the latch.

Install the other rail in the same way.

Notice: Keep the front and rear brackets at the same height, and keep the

two rails on the same level.

Remove the screws within the left and right lugs. Pull the server outward, and

pull the latches on the inner rails upward to remove the server from the rack.

Slightly lift up the keyhole spring plates, and slide the inner rails forward to

remove the inner rails.

Caution: Do not over bend the spring plate to avoid damage.

Removing the rails

Open the latches on the front brackets, and remove the rails.

Pull down the covers of the left and right lugs, and tighten the screws within.

Inner rail

Middle rail

Front bracket

Outer rail

Rear bracket

Installing the rails

Rail I: Pull the latch upward, and pull the inner rail outward to remove it.

Rail II: Pull the white tab forward and take out the inner rail.

Align the keyholes on the inner rail with the standoffs on the chassis, and push

the rail in the direction of the arrow to install the inner rail onto the chassis.

➋

➊

Innerrail

Middlerail

Outerrail

white

2 2

1 1

Rail I Rail II

The following describes the installation methods of two kinds of screw-free rails.

Please select the suitable method according to the specific rails. 1 1

Rail I Rail II

Rail II: Pull or push the blue release tab, and

push the server inward until the inner rails fully

enter the middle rails. Press the two tabs on

the middle rails while pushing the server into

place.

Rail I: Pull the latches on the inner rails upward,

and push the server into place.

blue

➋

➊

Andere Handbücher für NF3120M5

Andere Inspur Server Handbücher

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF5288M5 Bedienungsanleitung

Inspur

Inspur NF5486M5 Bedienungsanleitung

Inspur

Inspur Yingxin NX 5440 Bedienungsanleitung

Inspur

Inspur NE5260M5 Bedienungsanleitung

Inspur

Inspur NF5266M6 Bedienungsanleitung

Inspur

Inspur Tiansuo TS860 Bedienungsanleitung

Inspur

Inspur NX8840 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur 3408 Series Merkblatt

Inspur

Inspur NF5486M5 Bedienungsanleitung

Inspur

Inspur NF8380M5 Bedienungsanleitung

Inspur

Inspur NF5488A5 Bedienungsanleitung

Inspur

Inspur NF8260M5 Bedienungsanleitung

Inspur

Inspur SA5212M4 Bedienungsanleitung

Inspur

Inspur I48M6 Bedienungsanleitung

Inspur

Inspur NF5468M6 Bedienungsanleitung

Inspur

Inspur NF5448A6 Kurzanleitung

Inspur

Inspur NF3180A6 Bedienungsanleitung

Inspur

Inspur NP5540M3 Bedienungsanleitung

Inspur

Inspur NF8480M5 Bedienungsanleitung

Inspur

Inspur Yingxin NP3020M2 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung