Inspur NF5280M6 Bedienungsanleitung
PN
Rack-Mounted Server
Installation Guide
(Integrated Rail Kit)
V1.0
Warnings!
Please keep this document for future reference.
15kg
30kg
50kg
Watch out for the scratches that may be caused by the cabinet, chassis or rails.
Be aware of electric shock when installing the servers into the cabinet in use.
●DO NOT block the vents on the server during installation, especially the vents on the front
and rear of the server.
●Remove the protective film from the chassis before installing servers into the rack.
●For proper ventilation, leave a minimum space of 15cm between two servers.
●For easy access of the front and rear ports and cabling, leave a minimum space of 70mm
between the front side of the server and the inner side of the cabinet’s front door, and
150mm between the rear side of the server and the inner side of the cabinet’s rear door.
●Always keep the air baes in place to ensure proper air flow and avoid air turbulence in the
server room.
●Installation must comply with local and regional electrical regulations. To reduce the risk of
personal injury, fire, or damage to the server, DO NOT overload the AC supply that provides
power to the rack.
●Servers can only be deployed in dedicated cabinets with ventilation holes or specialized
cooling cabinets to avoid server failure from overheating as they are high power appliances.
●In case of multiple-server deployment, always load from bottom to top and place the heavier
server on the lower bay.
●DO NOT install devices beyond the cabinet’s load-bearing capacity, power supply capacity
and heat dissipation capacity.
For devices ≥ 15kg, it requires at least 2 people.
For devices ≥ 30kg, it requires at least 3 people.
For devices ≥ 50kg, it requires at least 4 people.
Align the pins on the front bracket to the front of the rack. Press the locking
latch on the front bracket as indicated by arrow , and then insert the pins
as indicated by arrow until the pins are fully engaged.
Rack-Mounted Server Installation Guide
V1.0
Rail-Kit Contents
Installing the Rails to the Server
1
1
3
2
2
4
4
5
Fully extend the inner rail until it clicks into a locked position. Repeat the
same step to extend the other inner rail.
Locate the front standoffs on
both sides of the server and
lower them into the J-slots on
the inner rails. Gently place the
server downward from the rear
to the front until all the
standoffs are firmly seated in
the J-slots.
7
Open both handles on the front
of the server, and then tighten
the two thumb screws to secure
the server in place.
6
Pull up the locking tabs on both
sides of the inner rails
simultaneously, and then slide
the server carefully all the way
into the rack.
Removing the Rails from the Server
Removing the Rails from the Rack
Align the pins on the rear bracket to the desired position of the back of the
rack. Press the locking latch as indicated by arrow , and then insert the
pins as indicated by arrow until the pins are fully engaged.
Repeat Step 1 and Step 2 for the other rail-kit.
NOTE: The front end and rear end of the rail, and the two rails MUST be
installed at the same height.
Open both handles on the front of the server, and then loosen the two
thumb screws.
Carefully slide the server out and pull
the tabs forward simultaneously to
release the server from the rail.
Pull up the locking tabs on both sides of the inner rails simultaneously,
and then slide the rails back.
Follow the preceding steps to remove the rails from the rack.
3
Middle Rail
Inner Rail
Back-Sliding Rail
Outer Rail
Front Bracket
Rear Bracket
Locking
Latch
Locking
Latch
Gently lift up and remove the server from the front to the rear. Before
removing the server from the rails, make sure that the eight standoffs on
the server are disengaged from the J-slots.
Rail 1
V1.0
1
1
3
2
2
4
3
5
4
Align the rail standoffs on each side of the system and lower them into the slots
on the rail. Put the system downward until all the rail standoffs are seated in the
slots.
Press the side-release lock buttons on both
rails and slide the system into the rack.
6
Locate and tighten the screws
under each handle on the system.
Identifying the Rail Kit Contents
Rail Kit is assembled by inner rail, middle rail and outer rail.
Installing Rails
Removing Rails
Position the rear bracket and align each pin with the rack holes. Pull the latch
release button on the rear bracket. Push the rail into the rack until the square
pins are fully seated on the rack holes and the latch clicks into place.
Repeat steps 1 and 2 to install the other side. And pull the inner rails out of the
rack until they lock into place.
Notice: Keep the left and right rails on the same level. Remove the screws from the left and right handles on the system.
Pull out the system and press the side-release lock buttons on both rails, and lift
the system up and away from rails.
Press the side-release lock buttons on both rails and slide the rails
into the rack.
Remove the rails as the same way of installing.
Rack-Mounted Server Installation Guide
Pull up the latch release part on the front bracket. Push the rail into the rack until
the square pins are fully seated on the rack holes and the latch clicks into place.
Notice: Keep the front and rear brackets on the same level.
Outerrail
Rearbracket
Frontbracket
Middlerail
Innerrail
Rail 2
Rack-Mounted Server Installation Guide
V1.0
Rail-Kit Contents
Installing the Rails
1
1
2
Align the pins on the front bracket to the front of the rack. Press the locking
latch as indicated by arrow ①, and then insert the pins as indicated by
arrow ② until the pins are fully engaged.
3
Repeat Step 1 and Step 2 for the other rail.
NOTE: The front end and the rear end of the rail, and the two rails MUST be
installed at the same height.
4
Align the server with the rails, and slide the chassis all the way into the rack.
Removing the Rails
Align the pins on the rear bracket to the desired position of the back of the
rack. Press the locking latch as indicated by arrow ①, and then insert the
pins as indicated by arrow ②until the pins are fully engaged.
Open both handles on the front of the server, and then tighten the two
thumb screws.
2
Slide the server out, and then remove
the server from the rack.
3
Disengage the pins from the rack.
5
Open both handles on the front of the server, and then loosen the two
thumb screws.
Outer Rail
Back-Sliding Rail Front Bracket
Rear Bracket
1
2
1
2
1
2
3
4
Locking
latch
Locking
latch
Rail 3
Andere Handbücher für NF5280M6
1
Dieses Handbuch passt für folgende Modelle
1
Andere Inspur Server Handbücher
Inspur
Inspur NF3120M5 Bedienungsanleitung
Inspur
Inspur Yingxin NP3020M2 Bedienungsanleitung
Inspur
Inspur NF8480M5 Bedienungsanleitung
Inspur
Inspur 3408 Series Merkblatt
Inspur
Inspur Yingxin NF5280M2 Bedienungsanleitung
Inspur
Inspur Yingxin Bedienungsanleitung
Inspur
Inspur TS860M5 Bedienungsanleitung
Inspur
Inspur NF5488M5 Bedienungsanleitung
Inspur
Inspur NF3120M5 Bedienungsanleitung
Inspur
Inspur NX8840 Bedienungsanleitung
Inspur
Inspur NF3120M5 Bedienungsanleitung
Inspur
Inspur NP5570M4 Bedienungsanleitung
Inspur
Inspur NF5466M5 Bedienungsanleitung
Inspur
Inspur NX5460M5 Bedienungsanleitung
Inspur
Inspur NF5266M5 Bedienungsanleitung
Inspur
Inspur NF5260FM6 Bedienungsanleitung
Inspur
Inspur NF3180A6 Bedienungsanleitung
Inspur
Inspur NF5266M6 Bedienungsanleitung
Inspur
Inspur Yingxin Bedienungsanleitung
Inspur
Inspur SA5212M4 Bedienungsanleitung
Beliebte Server Handbücher anderer Marken
iRobo
iRobo IPC2U Bedienungsanleitung
Nortel
Nortel 1000 Con?guration guide Bedienungsanleitung
Asus
Asus AP7500 Bedienungs- und Wartungshandbuch
Avid Technology
Avid Technology AirSpeed 5000 Bedienungsanleitung
HP
HP Integrity rx2600 Installationsanleitung
Milestone
Milestone Husky IVO 350T Bedienungsanleitung