Inspur SA5212M4 Bedienungsanleitung

No part of this document may be reproduced or transmitted in any form or by any means

without prior written consent of Inspur.

The information in this manual is subject to change without notice.

Inspur is the registered trademark of Inspur. All the other trademarks or registered

trademarks mentioned in this manual are the property of their respective holders.

Edition: 1

Sep 2016

Abstract

This manual contains technical information such as specifications, hardware

operations, software configuration, fault diagnosis, etc. that are relevant to the

maintenance and operation of this server.

It is recommended that server installation, configuration, and maintenance is

performed by experienced technicians only.

Target Audience

This manual is intended for:

●Technical support engineers

●Product maintenance engineers

●Technicians

Warnings:

This manual introduces the server’s technical features, system installation and

setup, which will help the user to understand how best to utilize the server and all its

functionalities.

1.For your safety, please do not disassemble the server’s components arbitrarily.

Please do not extend conguration or connect other peripheral devices arbitrarily. If

needed, please contact Inspur for our support and guidance.

2.Before disassembling the server’s components, please be sure to disconnect all

the power cords connected to the server.

3.BIOS and BMC setup is a signicant factor in correctly conguring your server. If

there are no special requirements, it is suggested to use the default values and not

alter the parameter settings arbitrarily.

4.Please use the driver shipped with the server or provided in Inspur ofcial website,

if you use non-Inspur driver, it may cause compatibility issues and affect the normal

use of the product, Inspur will not assume any responsibility or liability.

The manufacturer is not responsible for any damages, including loss of prots,

loss of information, interruption of business, personal injury, and/or any damage or

consequential damage without limitation, incurred before, during, or after the use of

our products.

Table of Content

1 Safety Instructions ...........................................................................................................1

2 Product Specication Introduction ...................................................................................6

2.1 Introduction...................................................................................................................6

2.2 Features and Specication ...........................................................................................6

3 Component Identication.................................................................................................9

3.1 3.5×12 Disk Position ....................................................................................................9

3.2 Hard Drive Bay LEDs ...................................................................................................9

3.3 Rear Panel....................................................................................................................10

3.4 System Board Components..........................................................................................11

3.5 System Board Jumper Introduction ..............................................................................13

4 Operations.......................................................................................................................14

4.1 Power up the Server.....................................................................................................14

4.2 Power down the Server ................................................................................................14

4.3 Extend the Server from the Rack..................................................................................14

4.4 Remove the Access Panel ...........................................................................................15

4.5 Install the Access Panel ...............................................................................................16

4.6 Remove the Air Bafe...................................................................................................16

5 Setup ...............................................................................................................................18

5.1 Optimum Environment..................................................................................................18

5.2 Rack Warnings .............................................................................................................21

5.3 Identifying the Contents of the Server Shipping Carton................................................21

5.4 Installing Hardware Options .........................................................................................22

5.5 Installing the Server into the Rack................................................................................22

5.6 Installing the Operating System....................................................................................23

6 Hardware Options Installation .........................................................................................24

6.1Processor Option...........................................................................................................24

6.2 Memory Options ...........................................................................................................26

6.3 Hot-plug Hard Drive Option ..........................................................................................27

6.4 Removing a Hot-plug Hard Drive..................................................................................28

6.5 Redundant Hot-plug Power Supply Option...................................................................29

6.6 PCIE Expansion Card Replacement ............................................................................30

6.7 Air Bafe Replacement.................................................................................................30

7 Cabling ............................................................................................................................31

8 BIOS Setup......................................................................................................................32

8.1 System BIOS Setup Methods.......................................................................................32

8.2 BIOS Conguration.......................................................................................................33

8.3Firmware Update...........................................................................................................67

9 BMC Settings ..................................................................................................................71

9.1 Introduction...................................................................................................................71

9.2 Functional Modules ......................................................................................................72

9.3 Web Interface Introduction ...........................................................................................73

9.4 Remote Control ............................................................................................................76

9.5 Power Supply and Heat Radiation................................................................................78

9.6 BMC Conguration .......................................................................................................79

9.7 Logs..............................................................................................................................82

9.8 Fault Diagnosis.............................................................................................................83

9.9 System Maintenance ....................................................................................................84

9.10 Command Line Function Introduction.........................................................................85

9.11 Time Zone Table ........................................................................................................90

10 Common Faults, Diagnosis and Troubleshooting..........................................................92

10.1 Common Faults ..........................................................................................................92

10.2 Diagnosis and Troubleshooting Instructions...............................................................93

11 Battery Replacement .....................................................................................................96

12 Regulatory Compliance Notices ....................................................................................97

12.1 Regulatory Compliance Identication Numbers .........................................................97

12.2 Federal Communications Commission Notice............................................................97

12.3 Cables ........................................................................................................................98

12.4 European Union Regulatory Notice ............................................................................98

12.5 Disposal of Waste Equipment by Users in the European Union.................................98

12.6 Korean Notice.............................................................................................................99

12.7 Chinese Notice ...........................................................................................................99

12.8 Battery Replacement Notice.......................................................................................99

13 Electrostatic Discharge..................................................................................................101

13.1 Preventing Electrostatic Discharge.............................................................................101

13.2 Grounding Methods to Prevent Electrostatic Discharge.............................................101

14 Inspur Support Guide ....................................................................................................102

Safety Introduction

1 Safety Instructions

Warning: Please be advised to follow the instructions below for safety. Failure to do

so could result to potential dangers that may cause property loss, personal injury or

death.

1. The power supplies in the system may produce high voltages and energy

hazards that may cause personal injury. For your safety, please do not attempt

to remove the cover of the system to remove or replace any component without

assistance provided by Inspur. Only service technicians trained by Inspur are

authorized to remove the cover of the host, and to remove and replace internal

components.

2. Please connect the equipment to the appropriate power supply. Use only power

supplies with the correct voltage and electrical specications according to the

label. To protect your equipment from damages caused by a momentary spike

or plunge of the voltage, please use relevant voltage stabilizing equipment, or

uninterruptible power supplies.

3. If you must use an extension cable, please use a three-core cable with properly

grounded plugs. Observe extension cable ratings. Ensure that the total rating of

all equipment plugged into the extension cable does not exceed 80 percent of

the ratings limit for the extension cable.

4. Please be sure to use the power supply components that come with the server,

such as power lines, power socket (if provided with the server) etc. For your

safety, please do not replace power cables or plugs randomly.

5. To prevent electric shock dangers caused by leakage in the system, please

make sure that the power cables of the system and peripheral equipment are

correctly connected to the earthed/grounded power socket. Please connect

the three-core power line plug to the three-core AC power socket that is well

earthed and easy to access. Be sure to use earthing /grounding pin of power

lines and do not use the patch plug or the earthing/grounding pin unplugged

with cables. In the case that the earthing/grounding conductors are not installed

and it is uncertain whether there are appropriate earthing/grounding protections,

please do not use or attempt to operate the equipment. Contact and consult an

electrician.

6. Please do not push any objects into the openings of the system. Doing so may

cause re or electric shock.

7. Please place the system far away from the cooling plate and heat sources, and

be sure not to block the air vents.

8. Please be sure not to scatter food or liquid in the system or on other

components, and do not use the product in humid or dusty environments.

9. Using an incompatible battery may cause explosion. When battery replacement

is required, please consult the manufacturer rst, and choose batteries of the

same or equivalent type. Do not disassemble, crush, puncture the batteries or

make the external connection point short circuit, and do not expose them in

the environment over 60°C. Never throw batteries into re or water. Please do

not attempt to open or repair the batteries. Dispose of used batteries according

to instructions. For battery recycling, please contact the local waste recycling

center.

10. Before installing equipment into the rack, please install all front and side

stabilizers on the independent rack rst. Please install the front stabilizers rst, if

connecting with other racks. Please install stabilizers before installing equipment

into the rack. Failure to install the corresponding stabilizers before installing

equipment into the rack may cause the cabinet to tip over, possibly resulting to

severe injury. After installing the equipment and other components into the rack,

only one component can be pulled out from the rack through its sliding part at

one time. Pulling out several components at the same time may cause the rack

to turn over, resulting to serious personal injury.

11. A minimum of two people are required to safely move a rack. The racks

are extremely awkward and heavy, moving them without adequate, trained

personnel could result in severe injury or death.

12. It is prohibited to directly short-circuit the copper busbar. Please do not touch the

copper busbar when the rack is powered on.

13. This is Class A product, and may cause radio interference. In such case, users

may need to take necessary measures to mitigate the interference.

Safety Introduction

14. The equipment is intended for installation in a Restricted Access Location.

Note: The following considerations may help avoid the occurrence of problems that

could damage the components or cause data loss, etc.

1. In the event of the following, please unplug the power line plug from the power

socket and contact Inspur’s customer service department:

1) The power cables, extension cables or power plugs are damaged.

2) The products get wet.

3) The products have fallen or have been damaged.

4) Other objects have fallen into the products.

5) The products do not or are unable to function normally even when attempting to

operate according to the instructions.

2. If the system becomes wet or damp, please follow these steps:

1) Power off the equipment, disconnect them with the power socket, wait for 10 to

20 seconds, and then open the host cover.

2) Move the equipment to a well-ventilated place to dry the system at least for 24

hours and make sure that the system is fully dried.

3) Close the host cover, reconnect the system to the power socket, and then power

on.

4) In case of operation failure or other abnormal situations, please contact Inspur

and get technical support.

3. Pay attention to the position of system cables and power cables-avoid placing

wires in high foot trafc locations. Please do not place objects on the cables.

4. Before removing the host cover, and/or touching the internal components,

please allow for the equipment to cool rst. To avoid damaging the mainboard,

please power off the system and wait for ve seconds, and then remove the

components from the mainboard and/or disconnect the peripheral device from

the system. Please remember that only service technicians trained by Inspur are

authorized to remove the cover of the host, and to remove and replace internal

components.

5. If there is modem, telecom or LAN options installed in the equipment, please

pay attention to the followings:

1) In the case of thunder and lightning, please do not connect or use the modem.

2) Never connect or use the modem in a damp environment.

3) Never insert the modem or telephone cables into the socket of network interface

controller (NIC).

4) Before unpacking the product package, installing internal components, touching

uninsulated cables or jacks of the modem, please disconnect the modem

cables.

6. In order to prevent electrostatic discharge from damaging the electronic

components in the equipment, please pay attention to the followings:

1) Please remove any static electricity on your body before dismounting or

touching any electronic component in the equipment, to prevent the static

electricity from conducting itself to the sensitive components. You may remove

the static electricity on the body by touching the metal earthing objects (such as

the unpainted metal surface on the rack).

2) Please do not take electrostatic sensitive components that are not ready to be

installed for application out of the antistatic package materials.

3) While working, please touch the earthing conductor or the unpainted metal

surface on the cabinet regularly to remove any static electricity from the body

that may damage the internal components.

7. Upon receiving the proper authorization from Inspur and dismounting the

internal components, please pay attention to the following:

1) Switch the system power supply off and disconnect the cables, including all

connections of the system. When disconnecting the cables, please hold the

connector of the cables and slowly pull the plugs out. Never pull on the cables.

2) The products need to completely cool down before dismounting the host cover

or touching the internal components.

3) During the dismounting process, avoid making large movement ranges to

prevent damage to the components or scratching arms.

4) Handle components and plug-in cards with care. Please do not touch the

components or connection points on the plug-in cards. When handling the

plug-in cards or components, firmly grab the edges of the plug-in cards and

components, and/or their metal xed supports.

8. During the process of rack installation and application, please pay attention to

Safety Introduction

the followings:

1) After the rack installation is finished, please ensure that the stabilizers have

been xed to the rack and supported to ground, and the weight of the rack is

rm on ground.

2) Always load from the bottom up, and load the heaviest items rst.

3) When pulling out the components from the rack, apply slight force to keep the

rack balanced.

4) When pressing down the release latch and the rail of components is sliding,

please be careful; as the sliding may hurt your ngers.

5) Do not overload the AC power supply branch circuits in the rack. The total load

of the rack should not exceed 80% of the ratings of the branch circuits.

6) Ensure that components in the rack have good ventilation conditions.

7) When repairing components in the rack, never step on any other components.

Inhaltsverzeichnis

Andere Inspur Server Handbücher

Inspur

Inspur 3408 Series Merkblatt

Inspur

Inspur NF5468A5 Bedienungsanleitung

Inspur

Inspur NF5266M5 Bedienungsanleitung

Inspur

Inspur OB5161M5 Bedienungsanleitung

Inspur

Inspur NF8380M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF8260M6 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF5488M5 Bedienungsanleitung

Inspur

Inspur NF8480M5 Bedienungsanleitung

Inspur

Inspur NF5888M5 Bedienungsanleitung

Inspur

Inspur Yingxin NX5440M4 Bedienungsanleitung

Inspur

Inspur NX5460M5 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NE5260M5 Bedienungsanleitung

Inspur

Inspur NX8840 Bedienungsanleitung

Inspur

Inspur NF5180M4 Bedienungsanleitung

Inspur

Inspur Tiansuo TS860 Bedienungsanleitung

Inspur

Inspur NF5466M5 Bedienungsanleitung

Inspur

Inspur Yingxin NX 5440 Bedienungsanleitung

Inspur

Inspur Yingxin Bedienungsanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Inspur

Inspur NF5266M6 Bedienungsanleitung

Inspur

Inspur NF5280M5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung