Intel Vectra VEi7 Bedienungsanleitung

Intel EtherExpress PRO 10+ ISA

Ethernet Adapter

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

General information to read before installing

On all systems: before installing LAN card, go into Bios setup and set PnP OS option field

to NO.

• How to change LAN card configuration if needed (Advanced users only)

This is a general advisory on how to forcibly modify resources for ISA and PCI network

cards.

ISA cards:

• For ISA network adapters, start the configuration tool provided in driver

kit (See install documentation)

• Under CMOS setup, go to Advanced > PnP/PCI ISA IRQ Resource Exclu-

sion > reserve an IRQ for the adapter.

PCI cards:

• For PCI network adapters, go to CMOS setup > Advanced > PnP/PCI ISA

IRQ Resource Exclusion > reserve the IRQ for Legacy ISA.

• ISA cards can’t use IRQ9

• IRQ 9 is reported as being used by ACPI during POST. This is due to ISA’s

inability to share IRQs.

• Using a different IRQ (e.g. 5, 7, 10, and 11) will work. For this:

1Install the NIC then power up the system.

2Press F2 to go to CMOS setup.

3Set PnP OS to NO and reserve IRQ 5, 7, 10, or 11 (explained in installation

section)

4Save the configuration settings and boot to the applicable OS.

5Follow installation steps.

Sound conflict under Win 95 on VLi8 only

• On VLi8, LAN cards cause an IRQ conflict with the embedded sound de-

vice under Win95.

• To solve the problem: Reserve IRQ 5 and sett PNP OS to no. For this:

1Install the NIC then power up the system

General information to read before installing

2Press F2 to go to CMOS setup.

3Set PNP OS to NO and reserve IRQ 5.

4Save settings and boot to applicable OS.

5Remote boot:

6Remote boot fails HP tests on Vectra VEi7.

7Message during boot on VEi8:

8Message “EtherExpress PRO flash routines disabled. ROM shadowing

problem.” appears when warm or cold booting the system.

The work-around for the above issues is to disable Plug and Play on the

NIC using the Intel SOFTSET2 utility and to disable shadowing in the

CMOS for the address region used by the NIC flash ram. Both must be

done. Disabling only the shadowing will not fix the problem.

1Boot into DOS 6.22.

2Run Intel’s SOFTSET2 utility. Go to “View adapter configuration” and

take down the Flash chip address for later use.

3Go back to main menu of SOFTSET2 and go to Change adapter config-

uration > Advanced Options menu > Set Plug and Play to Disabled.

For remote boot set Remote boot program to NDIS or Netware ODI de-

pending on the OS of the remote boot server. Save settings and exit

SOFTSET2.

4The system will reboot.

5Press F2 to go into CMOS settings. Go to Advanced > Shadow Options

> At a minimum, disable shadowing for the address region noted in

step 2. Save settings and exit SOFTSET2.

6Reboot the system.

7The Intel Flashstart configuration utility starts by default. Press the

spacebar twice to go to main menu > Exit. Note that after exiting, the

user will be given the option to start the Flashstart utility again on the

next reboot.

Another option to prevent the issues from occurring is to disable the

Flash memory feature on the NIC.

NOTE This option disables remote boot.

1 Run Intel SOFTSET2 utility.

General information to read before installing

9From main menu go to Change adapter configuration > Change “Flash

Memory” to Disabled.

1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 3.51 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and driver disk version

3.50.

• Driver File: PROW95.VXD, version 1.43a

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT 3.51 Server system that supports NetBEUI,

NWLink IPX/SPX Compatible Transport, and NWLink NetBIOS network

protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the EtherExpress PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the EtherExpress PRO 10+ driver disk, “PRO/10+ ISA LAN Adapter

Configuration and Driver Diskette” and execute “SOFTSET2.EXE”.

5Select “View Adapter Configuration” and verify the resource settings

listed above under the heading “Device Configuration”.

6Save any required changes and exit.

7Remove the Intel driver diskette from the floppy drive and restart the

system.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

1 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Connecting to a Windows NT 3.51 Server

8Windows 95SR2.5 will automatically recognize the Intel ethernet card as

“Intel EtherExpress PRO/10 (PnP Enabled)”.

9Insert the “PRO/10+ ISA LAN Adapter Configuration and Driver Diskette”

in the floppy drive and click on “Next” from the Update Device Driver

Wizard dialog box.

10 When Windows 95 detects the updated driver, “Intel EtherExpress{TM}

PRO/10+ {PnP Enabled}”, click on “Finish”.

11 Insert the Windows 95 CDROM when prompted. The system will copy all

the necessary files to complete the installation.

12 Click on “OK” when the system prompts for the computer and workgroup

names.

13 Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

14 Remove the Intel diskette from the floppy drive and click on “YES” to

restart the system when prompted.

15 Right-click on the “Network Neighborhood” icon and select “Properties”.

16 Accept the default Network Protocols and the Primary Network Logon

(Client for Microsoft Networks) as seen below and click on “OK”. (If you

do not have the required information, contact your network

administrator)

17 Client for Microsoft Networks

Client for Microsoft Networks

Intel EtherExpress[TM] PRO/10+ [PnP Enabled]

IPX/SPX-compatible Protocol

NetBEUI

18 Click on “OK” to accept the configuration.

19 Specify the path to your Windows 95 files when prompted.

2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a

Windows NT 4.0 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and driver disk version

3.50.

• Driver File: PROW95.VXD, version 1.43a

• Microsoft Windows 95 SR2.5 media.

• Microsoft Windows NT 4.0 Server system that supports NetBEUI, NWLink

IPX/SPX Compatible Transport, and NWLink NetBIOS network protocols.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the EtherExpress PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the EtherExpress PRO 10+ driver disk, “PRO/10+ ISA LAN Adapter

Configuration and Driver Diskette” and execute “SOFTSET2.EXE”.

5Select “View Adapter Configuration” and verify the resource settings

listed above under the heading “Device Configuration”.

6Save any required changes and exit.

7Remove the Intel driver diskette from the floppy drive and restart the

system.

8Windows 95SR2.5 will automatically recognize the Intel ethernet card as

“Intel EtherExpress PRO/10 (PnP Enabled)”.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

2 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Connecting to a Windows NT 4.0 Server

9Insert the “PRO/10+ ISA LAN Adapter Configuration and Driver Diskette”

in the floppy drive and click on “Next” from the Update Device Driver

Wizard dialog box.

10 When Windows 95 detects the updated driver, “Intel EtherExpress{TM}

PRO/10+ {PnP Enabled}”, click on “Finish”.

11 Insert the Windows 95 CDROM when prompted. The system will copy all

the necessary files to complete the installation.

12 Click on “OK” when the system prompts for the computer and workgroup

names.

13 Enter the Computer Name, Workgroup, and Computer Description in the

appropriate spaces and click on “Close” (Contact your network

administrator if you do not have the required information).

14 Remove the Intel diskette from the floppy drive and click on “YES” to

restart the system when prompted.

15 Right-click on the “Network Neighborhood” icon and select “Properties”.

16 Accept the default Network Protocols and the Primary Network Logon

(Client for Microsoft Networks) as seen below and click on “OK”. (If you

do not have the required information, contact your network

administrator)

17 Client for Microsoft Networks

Client for Microsoft Networks

Intel EtherExpress[TM] PRO/10+ [PnP Enabled]

IPX/SPX-compatible Protocol

NetBEUI

18 Click on “OK” to accept the configuration.

19 Specify the path to your Windows 95 files when prompted.

3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet Adapter

Microsoft Windows 95 SR2.5

3 Installing the Intel EtherExpress PRO 10+ ISA Ethernet

Adapter

Microsoft Windows 95

SR2.5

Connecting to a Novell

Netware 3.12 Server

Requirements

• HP Vectra with Windows 95 SR2.5.

• Intel EtherExpress PRO 10+ ISA Ethernet card and drivers disk version

3.50.

• Driver File: PROW95.VXD, version 1.43a

• Microsoft Windows 95 SR2.5 media.

• Novell NetWare 3.12 Server system that supports IPX network protocol.

• Novell Client for Windows 95 v2.5 installation media.

Device Configuration

Procedure

1With the HP Vectra turned off, install the Intel EtherExpress PRO 10+ ISA

adapter card into an ISA slot.

2Connect network cable media to the EtherExpress PRO 10+ card.

3Power on the machine and start Windows 95SR2.5 in MS-DOS mode.

4Insert the EtherExpress PRO 10+ driver disk, “PRO/10+ ISA LAN Adapter

Configuration and Driver Diskette” and execute “SOFTSET2.EXE”.

5Select “View Adapter Configuration” and verify the resource settings

listed above under the heading “Device Configuration”.

6Save any required changes and exit.

7Remove the Intel driver diskette from the floppy drive and restart the

system.

8Windows 95SR2.5 will automatically recognize the Intel ethernet card as

“Intel EtherExpress PRO/10 (PnP Enabled)”.

Device Configuration Vectra Vli8 Vectra VEi7 Vectra VEi8

Interrupt 05 03 07

I/O Address 210 210 210

Andere Handbücher für Vectra VEi7

Dieses Handbuch passt für folgende Modelle

Andere Intel Adapter Handbücher

Intel

Intel X540-T2 Bedienungsanleitung

Intel

Intel 10 Gigabit AT Ethernet Server Adapter Referenzhandbuch

Intel

Intel INTEL 10 GIGABIT AT2 SERVER ADAPTER Bedienungsanleitung

Intel

Intel QLE7342 Bedienungsanleitung

Intel

Intel PRO/1000 T Bedienungsanleitung

Intel

Intel PCIe 2-Port 2.5G 4-Speed Bedienungsanleitung

Intel

Intel I350 Bedienungsanleitung

Intel

Intel ETHEREXPRESS PRO/100 Bedienungsanleitung

Intel

Intel Ethernet X520 10GbE Dual Port KX4 Mezz Bedienungsanleitung

Intel

Intel PROWIRELESS 3945ABG NETWORK CONNECTION Bedienungsanleitung

Intel

Intel PRO/Wireless 2011B LAN USB Device Installations- und Betriebshandbuch

Intel

Intel PRO/1000 PF Referenzhandbuch

Intel

Intel QuickAssist 8920SCC Bedienungsanleitung

Intel

Intel X520-T2 Referenzhandbuch

Intel

Intel PRO/Wireless 5000 Bedienungsanleitung

Intel

Intel RSP3TD160 Installationshandbuch

Intel

Intel NUC CEC Bedienungsanleitung

Intel

Intel PRO 1000 PT DESKTOP ADAPTER Bedienungsanleitung

Intel

Intel 2200BG Bedienungsanleitung

Intel

Intel ETHEREXPRESS PRO/100 Bedienungsanleitung

Intel

Intel PRO/1000 T Bedienungsanleitung

Intel

Intel 1000BASE-T Bedienungsanleitung

Intel

Intel 2011B - PRO/Wireless LAN Enterprise Access... Bedienungsanleitung

Intel

Intel CentrUser's Guideino Advanced-N + WiMAX 6250 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung