Intel ISP1100 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel®ISP1100 Internet Server

Quick Start Guide

A Guide for Technically Qualified Assemblers of Intel®Identified

Subassemblies/Products

Before You Begin................................................................................................................. 2

FCC/Emissions Disclaimer........................................................................................... 2

Cautions and Warnings ...............................................................................................2

Safety and Regulatory Requirements.......................................................................... 3

Site Criteria..................................................................................................................3

Unpack and Inspect the Server ............................................................................................ 3

Check the Accessories ................................................................................................ 4

Check the Power Cord................................................................................................. 4

Install Components............................................................................................................... 5

Tools and Supplies Needed......................................................................................... 5

Remove the Cover....................................................................................................... 5

Install the Processor.................................................................................................... 6

Install the Memory ....................................................................................................... 8

Install the Hard Drive(s)............................................................................................. 10

Install PCI Add-in Card(s).......................................................................................... 12

Close the Cover......................................................................................................... 17

Install the Rackmount Brackets ................................................................................. 17

Rackmount the Server........................................................................................................ 18

Power Up the Server.......................................................................................................... 19

Access the Additional Documents...................................................................................... 20

Need Help? ........................................................................................................................ 22

The most current version of this document and other documents relating to the Intel®ISP1100 Internet

Server can be found at http://www.intel.com/isp

any form, or by any means without prior written consent of Intel.

Intel Corporation (Intel) makes no warranty of any kind with regard to this material, including, but not limited to, the

implied warranties of merchantability and fitness for a particular purpose. Intel assumes no responsibility for any

errors that may appear in this document. Intel makes no commitment to update nor to keep current the information

contained in this document.

†Third-party brands and trademarks are the property of their respective owners.

Order Number: A10529-001

2 Intel ISP1100 Internet Server Quick Start Guide

Before You Begin

FCC/Emissions Disclaimer

This equipment has been tested and verified to comply with Class A limits when configured into a

compatible host computer, pursuant to Part 15 of the FCC Rules, CISPR 22, and EN55022. These

limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

To ensure EMC compliance with your local regional rules and regulations, the final configuration

of your end system product may require additional EMC compliance testing. For more information

please contact your supplier.

Cautions and Warnings

Read and adhere to all warnings, cautions, and notes in this guide and the documents supplied with

the chassis, power supply, server board, and accessories. If the instructions for the chassis, server

board, and power supply are inconsistent with these instructions or the instructions for accessories,

contact the supplier to find out how you can ensure that your server meets safety and regulatory

requirements.

WARNINGS

Make sure the AC power connection is through a properly grounded

outlet. See “Check the Power Cord” in the “Unpack and Inspect the

Server” procedure for more information.

Pressing the Power button DOES NOT turn off all power to this server.

Some circuitry in the server may continue to operate even though the

front panel Power button is off. Disconnect the server from the AC

power source and from any telecommunications links, networks, or

modems before performing any of the procedures in this guide. Failure

to do so can result in personal injury or equipment damage.

This guide is for qualified technical personnel with experience installing

and configuring servers.

CAUTIONS

Perform the procedures in this guide only at an ESD workstation since the

server components can be extremely sensitive to ESD. If no such station is

Intel ISP1100 Internet Server Quick Start Guide 3

available, you can reduce the risk of electrostatic discharge (ESD) damage

by doing the following:

•Wear an antistatic wrist strap and attach it to a metal part of the server.

•Touch the metal on the server chassis before touching the server components.

•Keep part of your body in contact with the metal server chassis to dissipate the static

charge while handling the server components.

•Avoid moving around unnecessarily.

•Hold the boards and drives only by the edges.

•Place the server components on a grounded, static-free surface. Use a conductive foam

pad if available but not the component wrappers.

Safety and Regulatory Requirements

See the Intel®ISP1100 Internet Server Product Guide for all applicable safety standards,

electromagnetic compatibility (EMC) regulations, and product certification markings.

Intended uses: This product was evaluated for use in computer racks within computer rooms and

similar locations. Other uses require further evaluation.

Site Criteria

Before beginning to unpack and prepare the server for operation, consider the following site

criteria:

•Near a properly earthed, grounded, three-pronged AC power outlet.

In the United States and Canada: a NEMA 5-15R outlet for 100-120 VAC.

In other geographic areas: a properly earthed, grounded AC power outlet in accordance

with the local electrical authorities and electrical code of the region.

•Clean and relatively free of dust.

•Well ventilated and away from sources of heat, with the ventilating openings on the server kept

free of obstructions.

•Away from sources of vibration or physical shock.

•Isolated from strong electromagnetic fields and noise caused by electrical devices such as

elevators, copy machines, air conditioners, large fans, large electric motors, radio and TV

transmitters, and high-frequency security devices. For EMI information, refer to the Intel

ISP1100 Internet Server Product Guide.

•Access space provided so the server power cord can be easily unplugged from the AC power

source (see previous “WARNINGS”).

Unpack and Inspect the Server

Remove the server from the packaging container and check that all the accessories are included.

Inspect the packaging container for evidence of mishandling during transit. If the packaging

container is damaged, photograph it for reference. After removing the contents, keep the damaged

container and the packing materials.

Inspect the server and accessories for damage. If the contents appear damaged, file a damage claim

with the carrier immediately.

4 Intel ISP1100 Internet Server Quick Start Guide

Check the Accessories

Examine the contents of the accessories pouch and make sure the following items are present:

•AC Power Cord

•Rackmount Brackets (2)

•Rackmount Bracket Screws (4)

•Intel®ISP1100 Internet Server Quick Start Guide

•Headless Network Installation of Red Hat Linux 6.1 Guide

•Red Hat Linux 6.1 CD-ROM

•Intel ISP1100 Internet Server Resource CD-ROM - Contains:

Intel ISP1100 Internet Server Quick Start Guide

Intel ISP1100 Internet Server Product Guide

Intel®ISP1100 Internet Server Technical Product Specification

Software drivers and utilities

If you find any parts missing, contact the supplier immediately.

✏NOTE

Save the packaging container and packing materials in the event you need to

package the server for reshipment.

Check the Power Cord

Check that the power cord is the exact type required in the region where the server will be used. Do

not modify or use the supplied AC power cord if it is not the correct type. Refer to the following

“Power Cord Requirements” for a detailed power cord description.

Power Cord Requirements

•Rating: Power cords must be rated for available AC voltage and have a current rating at least

125% of the server current rating. (Refer to the Intel ISP1100 Internet Server Technical

Product Specification included on the Intel Internet Server Resource CD-ROM shipped with

the server for power requirement information.)

•Connector, wall outlet end: Power cords must be terminated in a grounding-type male plug

designed for use in your region. Cords must have certification marks showing certification by

an agency that is acceptable in your region.

•Connector, power supply end: The connector that plugs into the AC receptacle on the server

power supply must be an IEC 320, sheet C13, type female connector.

•Cord length and flexibility: Power cord length must be 4.5 meters (14.76 feet) or less and

composed of flexible (harmonized <HAR>) cord or VDE-certified cordage to comply with

server safety certifications.

Intel ISP1100 Internet Server Quick Start Guide 5

Install Components

The following procedures describe how to install the necessary components that enable you to

operate the server system. These procedures are in the recommended installation sequence and

should be performed in the order presented.

Before performing the following installation procedures, do not forget to thoroughly familiarize

yourself with the safety warnings and cautions in the “Before You Begin” section of this guide.

Tools and Supplies Needed

•Phillips (cross-head) screwdriver (number 1 and 2 bit)

•Antistatic wrist strap and conductive foam pad (recommended)

Remove the Cover

Perform the following procedure to remove the cover and gain access to the server internal

components (refer to Figure 1):

1. Use a Phillips screwdriver and remove the screw (A) from the front edge of the cover.

2. Grasp the back edge of the cover and simultaneously pull from the back edge and push near the

front until the cover slides out from under the edge of the server front panel.

3. Grasp the notch (B) in the front center of the cover and lift to remove the cover.

OMO9429

Figure 1. Removing the Cover

6 Intel ISP1100 Internet Server Quick Start Guide

Install the Processor

This procedure describes how to install the processor chip on the server board. Before proceeding,

be sure you are thoroughly familiar with the “Before You Begin” information at the front of this

guide. Read the following “Preliminary Considerations” to ensure that you install the correct

processor in the server.

Preliminary Considerations

Table 1 lists and describes the Intel®processors supported by the server.

Table 1. Supported Processors

Processor Type L2 Cache Size (KB) FSB Speed (MHz) Speed (MHz)

Intel®Celeron™ processor 128 66 5661, 533, 500

466, 433, 400

366

Intel®Pentium®III processor 256 100 750, 700

650, 600E

550E, 500

1 Coppermine 128 KB; other Intel Celeron processors are based on Mendocino core.

Remove the Processor Fan

Due to space constraints, the server will not accommodate a processor with a fan mounted on top

of the heat sink. Sufficient cooling is provided without a processor fan (five fans are mounted on

the server chassis). Thus, if the processor you wish to install has a fan mounted on the heat sink,

remove the fan as described in the following procedure. Otherwise, proceed to the installation

procedure.

Remove the fan from the processor as follows (refer to Figure 2):

1. Grasp the fan housing at the four corners.

2. Gently press on the corners and lift until the fan releases from the heat sink.

OMO9430

Figure 2. Removing the Processor Fan

Intel ISP1100 Internet Server Quick Start Guide 7

Install the Processor Chip

Perform the following procedure to install the processor chip on the server board (refer to

Figure 3):

1. Grasp the end of the zero-insertion-force (ZIF) arm (A) and bend it out slightly until it

disengages from the socket tab (B).

2. Swing the ZIF arm up until it stops in the straight up position. The processor socket is now

unlocked.

3. Face the front of the server and orient the processor chip (C) with the notch (D) in the upper

left corner of the processor socket (E).

4. Gently place the processor chip on the socket so that the processor pins (F) mate exactly with

the corresponding socket pins (G). Do not force the processor into the socket since it takes

only a slight pressure to bend the pins.

5. With the processor in place, swing the arm (A) down until it snaps into the socket tab (B). The

processor is now properly socketed.

OMO9431

Figure 3. Installing the Processor Chip

8 Intel ISP1100 Internet Server Quick Start Guide

Install the Heat Sink

Perform the following procedure to install the heat sink on the processor chip (refer to Figure 4):

1. Orient the heat sink so the thermal grease pad (A) on the heat sink is exactly aligned with the

corresponding thermal grease pad (B) on top of the processor chip.

2. With the end of the clamp that has the two slots (C) facing the front of the socket, drop the

clamp in the bottom of the heat sink center groove (D).

3. Make sure the end of the clamp with the two slots (C) is positioned just below the top edge of

the heat sink and press down on the back of the clamp (E) until it snaps onto the socket tab (F).

4. With the front of the clamp below the top edge of the heat sink, press down on the front of the

clamp (G) until it snaps onto the socket tab (H).

OMO9432

Figure 4. Installing the Heat Sink

Install the Memory

This procedure describes how to install DIMM board memory in the server. Before proceeding, be

sure you are thoroughly familiar with the “Before You Begin” information at the front of this

guide.

Read the following “Preliminary Considerations” to ensure that you use the correct DIMM

board(s) and properly install them in the server.

Preliminary Considerations

•The server board has four DIMM board sockets that can accommodate 16 MB to 1 GB of

SDRAM.

•Memory size can vary between sockets.

•DIMM boards can be installed in any order. However, it is easier to start with the back socket

and move toward the front.

•Empty sockets between DIMM boards is permitted.

•DIMM memory sizes can be mixed if all installed DIMM memory size is either unbuffered or

registered.

Intel ISP1100 Internet Server Quick Start Guide 9

Table 2. Supported Memory Characteristics

DIMM

Size Configuration DRAM

Technology DRAM

Depth DRAM

Width Single-sided DIMM

(Size x 64 Bit) Double-sided DIMM

(Size x 64 Bit)

16 MB 2 Mbit x 72 16 Mbit 2 Mbit 8 bit 2 MB x 8 B = 16 MB

32 MB 4 Mbit x 72 16 Mbit 2 Mbit 8 bit 4 MB x 8 B = 32 MB

32 MB 4 Mbit x 72 16 Mbit 4 Mbit 4 bit 4 MB x 8 B = 32 MB

64 MB 8 Mbit x 72 16 Mbit 4 Mbit 4 bit 8 MB x 8 B = 64 MB

32 MB 4 Mbit x 72 64 Mbit 4 Mbit 16 bit 4 MB x 8 B = 32 MB

64 MB 8 Mbit x 72 64 Mbit 4 Mbit 16 bit 8 MB x 8 B = 64 MB

64 MB 8 Mbit x 72 64 Mbit 8 Mbit 8 bit 8 MB x 8 B = 64 MB

128 MB 16 Mbit x 72 64 Mbit 8 Mbit 8 bit 16 MB x 8 B = 128 MB

128 MB 16 Mbit x 72 64 Mbit 16 Mbit 4 bit 16 MB x 8 B = 128 MB

64 MB 8 Mbit x 72 128 Mbit 8 Mbit 16 bit 8 MB x 8 B = 64MB

128 MB 16 Mbit x 72 128 Mbit 8 Mbit 16 bit 16 MB x 8 B = 128 MB

128 MB 16 Mbit x 72 128 Mbit 16 Mbit 8 bit 16 MB x 8 B = 128 MB

256 MB 32 Mbit x 72 128 Mbit 16 Mbit 8 bit 32 MB x 8 B = 256 MB

Additional Memory Characteristics

•168-pin SPD with gold-plated contacts.

•Single or double-sided DIMM boards.

•66 MHz or 100 MHz unbuffered or registered SDRAM, 72-bit ECC, 3.3V only memory

•Unbuffered 16 MB, 32 MB, 64 MB, 128 MB, and 256 MB DIMMs for a total memory size of

1 GB.

•Registered 64 MB, 128 MB, and 256 MB DIMMs for a total memory size of 1 GB. Double-

stacked DIMM boards are not supported due to space limitations on the server board.

•All memory components used with this server must comply with the following PC SDRAM

specifications (refer to the Intel ISP1100 Internet Server Technical Product Specification

included on the Intel Internet Server Resource CD-ROM shipped with the server for

information about where to obtain these specifications):

PC SDRAM Specification (memory component specific)

PC Unbuffered SDRAM Specifications

PC Serial Presence Detect Specification

•Processors with 100 MHz host bus speed should be paired with 100 MHz SDRAM.

•Processors with 66 MHz host bus speed can be paired with either 66 MHz or 100 MHz

SDRAM. However, 100 MHz SDRAM will not increase the performance of a processor with

66 MHz host bus speed.

10 Intel ISP1100 Internet Server Quick Start Guide

Install the DIMM Board(s)

Perform the following procedure to install the DIMM boards on the server board (refer to

Figure 5):

1. Orient the DIMM board so the key slots (A) in the DIMM board edge connector are properly

aligned with the corresponding slots in the mating server board socket (B). (The connectors

are keyed to mate in only one direction.)

2. Firmly press the DIMM board straight down and all the way into the server board socket.

3. Make sure the DIMM board is locked in by pressing the levers (C) on each end of the server

board socket into the mating notches (D) on each edge of the DIMM board.

OMO9433

Figure 5. Installing the DIMM Boards

Install the Hard Drive(s)

This procedure describes how to install the hard drive(s) in the server drive bays. Each of the two

drive bays on the right side of the server accommodates a 1-inch hard drive.

Before proceeding, be sure you are thoroughly familiar with the “Before You Begin” information

at the front of this guide.

Andere Handbücher für ISP1100 - Server Platform - 0 MB RAM

Inhaltsverzeichnis

Andere Intel Server Handbücher

Intel

Intel M50FCP2UR Bedienungsanleitung

Intel

Intel GS-SR168 Benutzerhandbuch

Intel

Intel SBXL52 - Server Compute Blade Betriebsanleitung

Intel

Intel R2000LH2 Bedienungsanleitung

Intel

Intel SC5650HCBRP Bedienungsanleitung

Intel

Intel R2000BB series Bedienungsanleitung

Intel

Intel SRPM8 Bedienungsanleitung

Intel

Intel S7000FC4UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SC450NX - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel P4000IP Series Konfigurationshandbuch

Intel

Intel R1000WF Series Bedienungsanleitung

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel SR1435VP2 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1530AHLX - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1500 - AXXMINIDIMM DDR-2 RAID Controller Cache... Bedienungsanleitung

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel ISP4400 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel IP Media Server Bedienungsanleitung

Intel

Intel R2000LH2 Bedienungsanleitung

Intel

Intel SR1670HV - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel R1304BTSSFAN Bedienungsanleitung

Intel

Intel SR1560SF - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel D50DNP Series Bedienungsanleitung

Intel

Intel R2000BB series Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung