Intel R1000RP Series Original Betriebsanleitung

* 2.5" hard drive bay system as shown

Thank you for buying an Intel® Server System. The following information will help you

assemble your Intel® Server System and install components.

If you are not familiar with ESD [ElectroStatic Discharge] procedures used during

system integration, see the complete ESD procedures described in your Service Guide.

This guide and other supporting documents are located on the web at:

http://www.intel.com/p/en_US/support/.

Intel® Server System R1000RP Family

Quick Installation User's Guide

G85599-002

(This page is intentionally left blank.)

General Installation Process ........................................................................................................ 2

Reference ............................................................................................................................................ 12

System Overview .............................................................................................................................. 1

Preparing the System ...................................................................................................... 2

Remove the Top Cover .................................................................................................... 2

Remove the Air Duct ........................................................................................................ 2

Remove Processor Heatsink ........................................................................................ 2

Install the Processor ........................................................................................................ 3

Install Processor Heatsink ............................................................................................. 4

Install Memory Modules .................................................................................................. 4

Install Hard Drives .............................................................................................................. 5

Install Optical Drive ............................................................................................................ 7

Install the Air Duct ............................................................................................................. 8

Remove Add-in Card Riser Assembly ...................................................................... 8

Install Add-in Card .............................................................................................................. 8

Install Add-in Card Riser Assembly ........................................................................... 8

Install Rack Handles .......................................................................................................... 8

Install Intel® I/O Expansion Module (optional) ..................................................... 9

Install Intel® ESRT2 RAID AXXRAKSW5 Upgrade Key (optional) ................ 9

Install Intel® Remote Management Module 4 (optional) ................................ 9

Install Intel® RAID Smart Battery (optional) ........................................................ 10

Replace Fixed Power Supply Module (optional) ............................................... 10

Replace Redundant Power Supply Module (optional) .................................. 10

Install Bezel (optional) .................................................................................................... 11

Install the Top Cover ........................................................................................................ 11

Finishing Up ......................................................................................................................... 11

Software ............................................................................................................................... 11

Table of Contents

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://www.intel.com/support/

motherboards/server/sb/cs-010770

.htm for complete safety information.

Installation and service

of this product is to be

performed only by

qualified service personnel

to avoid risk of injury from

electrical shock or energy

hazard.

Warning Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to server board and/or

other components.

Tools Required

Anti-static

wrist strap

Phillips*

screwdriver

Intel®is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the

Thermal Operation and Conﬁguration Requirements

To keep the system operating within supported maximum thermal limits, the system must meet the following operating and configuration

guidelines:

• Ambient in-let temperature cannot exceed 35 ºC and should not remain at this maximum level for long periods of time.

Doing so may affect long term reliability of the system.

•DIMM Population on CPU: Install DIMMs the in order; Channels A, and B. Start with 1st DIMM slot (blue) on each channel.

•All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied drive blank.

•The air duct must be installed at all times.

• The system top-cover must be installed at all times.

System Fans

Memory Slots

PCI Slots

Server Board

CPU

Air Duct

Hard Drive Bays

Front Control Panel

Power Supply

System Features and Components

* 2.5" Hard Drive Bay system as shown

System Overview

Intel® Server System R1000RP Family

General Installation Process

The installation instructions in this section are for common components of Intel® Server System

R1000RP family.

Minimum Hardware Requirements

•Memory Type:

Minimum of one 1GB DDR3L 1333/1600 MHz ECC UDIMM

•Processor: Intel®Xeon®processor E3-1200 V3 product family or the 4th

Generation Intel®Core™ i3 processor series.

•Hard Disk Drives: SATA

For a complete list of compatible processors, heatsinks, and memory, see

http://www.intel.com/p/en_US/support/ (post-production only)

To avoid integration difﬁculties and possible board damage, your system must meet

the following minimum requirements:

Preparing the System

Observe normal ESD (Electrostatic Discharge)

procedures.

Place your Intel®Server System on a ﬂat anti-static

surface to perform the following integration procedures.

Observe ESD procedures before reaching inside to make

server board connections or install components.

IMPORTANT!

Before proceeding

further, check your

Intel®Server System

for disconnected or

loose cables and

components that

may have occurred

during shipping. TIM

Chassis Front

Remove Processor Heatsink

The heatsink is attached to the server board / processor socket with captive fasteners.

Lift the heatsink straight up.

CAUTION: The heatsink has thermal interface material (TIM) on the underside

of it. Use caution so that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

Using a #2 Phillips* screwdriver, loosen the four screws located on the

heatsink corners in a diagonal manner using the following procedure:

Using a #2 Phillips* screwdriver, start with screw 1 and loosen it by

giving it two rotations and stop. (IMPORTANT: Do not fully loosen.)

Proceed to screw 2 and loosen it by giving it two rotations and stop.

Similarly, loosen screws 3 and 4.

Repeat steps A and B by giving each screw two rotations each time

until all screws are loosened.

Remove the Top Cover

Remove the four screws.

Slide cover back

and lift upward.

Remove the Air Duct

Remove the air duct by

lifting straight up.

General Installation Process

5Install the Processor

Cautions:

When removing the protective

cover, DO NOT TOUCH the

gold socket pins.

When unpacking a processor,

hold by the edges only to avoid

touching the gold contact pins.

To avoid damage, DO NOT

DROP the cover onto the

socket pins or components.

A. Open the Socket Lever

Push the lever

handle

down

and away

from the socket

to release it.

Rotate the lever

open all the way.

B. Open the

Load Plate

C. Unpack the Processor

Open the load

plate as shown.

Carefully remove

protective cover

as shown.

Save the

protective

cover.

Install the Processor ... continued

CAUTION: The underside of the processor has components

that may damage the socket wires if installed improperly.

Processor must align correctly with the socket opening

before installation.

DO NOT DROP processor into socket!

Components

Orient the processor with the socket so that the processor

cutouts match the two

socket pins.

Note location

of gold key at

corner of

processor.

Install the Processor

Carefully lower the load plate

over the processor.

E. Close the Load Plate

Carefully lower the load plate

over the processor.

Install the Processor ... continued

Make sure the front edge of the load plate

slides under the shoulder

screw as the lever is

lowered.

Close the load

plate locking

lever.

Load Plate

Front Edge

Shoulder

Screw

F. Engage the Load Plate

Push down on the locking lever.

Slide the tip

of the lever

under the

notch in the

load plate.

Make sure

the lever is securely latched.

CAUTION: DO NOT damage the

server board with the tip of the

locking lever.

Save the

protective

cover.

Remove the Cover

Carefully lift the cover

straight up as shown.

G. Latch the Locking Lever

General Installation Process

AIRFLOW

Chassis Front

TIM

CAUTION:

Do not

over-tighten

fasteners.

Note: Heatsink styles may vary.

Remove the protective film on the TIM if present.

CAUTION: The heatsink has thermal interface

material (TIM) on the underside of it. Use caution so

that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

BAlign heatsink fins to the front and back of

the chassis for correct airflow.

Airflow goes from front-to-back of chassis.

Each heatsink has four captive fasteners and

should be tightened in a diagonal manner using

the following procedure:

Using a #2 Phillips* screwdriver,

start with screw 1 and engage screw

threads by giving it two rotations

and stop. (Do not fully tighten.)

Proceed to screw 2 and engage screw

threads by giving it two rotations and

stop. Similarly, engage screws 3 and 4.

Repeat steps C and D by giving each

screw two rotations each time until

each screw is lightly tightened up to

a maximum of 8 inch-lbs torque.

6Install Processor Heatsink 7Install Memory Modules

DDR3L DIMM Memory Identiﬁcation:

Other

Memory

DDR3

CAUTION: Observe normal ESD (ElectroStatic

Discharge) procedures to avoid possible damage to

system components.

DIMM notch and socket bump must align as shown below.

This server board supports up to 6 DDR3L 1333/1600

ECC UDIMM. Non-ECC memory is NOT supported by

this server board.

Note: For additional memory conﬁgurations, see the Service Guide on the

Intel®Server Deployment & Management DVD that accompanied

your Intel®Server System, or go to:

http://www.intel.com/p/en_US/support/ (post-production)

Memory sizing and conﬁguration is supported only for qualiﬁed DIMMs approved by

Intel®. For a list of supported memory, go to:

http://serverconfigurator.intel.com/sct_app.aspx (post-production)

For the best performance, a minimum of three DIMMs per CPU is recommended,

populated in the blue slot of each memory channel.

Install Memory Modules ...continued

Memory Conﬁgurations and Population Order:

Intel®Server Board S1200V3RPM

DIMM_A2

DIMM_A1

DIMM_B2

DIMM_B1

CPU Socket

Install DIMM Memory Modules ... Continued

To Install DIMMs:

Open both DIMM socket levers.

Note location of alignment notch.

CAUTION: Avoid touching contacts

when handling or installing DIMMs.

IMPORTANT! Visually check that each latch is fully closed and correctly engaged with each DIMM edge slot.

Push down firmly on the DIMM until it snaps into place and both levers close.

Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.

General Installation Process

8Install

Hard Drives

2.5" HDD

2.5" Hard Drive Carrier (For system with 2.5" hard drive bay only)

Hard Drive Numbering Diagram

Drive 0 Primary

8 x 2.5" hard drive bay as shown

Remove the drive carrier by pressing the

green

latch

to unlock.

Pull out the black lever and slide the carrier out.

Remove the four screws securing the plastic drive blank

from the 2.5” HDD carrier.

Disengage the plastic drive blank from the HDD carrier.

Remove the plastic drive blank from the 2.5” HDD carrier.

Install the hard disk drive using the four screws as shown. Make Sure

that the connector end of the drive matches the backplane connector.

With the lever open, insert the hard disk drive assembly into the chassis,

then push in the lever to lock it into place.

CAUTION: If you do not

install all drives, empty drive

bays must be occupied by

carriers with plastic drive

blank provided to maintain

proper system cooling.

General Installation Process

2.5" HDD

Install

Hard Drives ...continued

3.5" Hard Drive Carrier (For system with 3.5" Hot Swap hard drive bay only)

Hard Drive Numbering Diagram

Drive 0 Primary

Remove the drive carrier by pressing the green button and opening

the lever.

Slide the carrier out.

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

Remove the four screws securing the HDD interface bracket and remove

the HDD interface bracket.

Install 2.5” Hard Drive as option:

3.5´´ HDD

Install the hard disk drive using the same four screws as shown. Make

sure the connector end of the drive matches the backplane connector.

With the lever open, insert the hard disk drive assembly into the chassis.

Push in the lever to lock it into place.

4 x 3.5” hard drive bay as shown

CAUTION: If you do not

install all drives, empty drive

bays must be occupied by

carriers with plastic drive

blank provided to maintain

proper system cooling.

d1 d4

d2 d3

Install the HDD interface bracket

from top. Secure the bracket with

three screws as shown.

Slide the 2.5” HDD into the

bracket to align the screw holes

with the right and the left rail.

Break off the tab on the

HDD interface bracket.

Secure the hard disk drive using

the four screws for 2.5” HDD.

Bottom

View

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

0 1 2 3

Inhaltsverzeichnis

Andere Intel Server Handbücher

Intel

Intel SBXD132 - Server Compute Blade Bedienungsanleitung

Intel

Intel SBXL52 - Server Compute Blade Betriebsanleitung

Intel

Intel MFSYS35 Bedienungsanleitung

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel M50FCP2UR Bedienungsanleitung

Intel

Intel R200LH2 Bedienungsanleitung

Intel

Intel M50CYP1UR Series Bedienungsanleitung

Intel

Intel R1304BTSSFAN Bedienungsanleitung

Intel

Intel S2600CW Bedienungsanleitung

Intel

Intel SR2400SYS - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel ISP1100 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel SR2612UR - Server System - 0 MB RAM Betriebsanleitung

Intel

Intel SR1670HV - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SR9000MK4U - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel MFSYS25 - AXXPSU 1000W Power Supply Module Bedienungsanleitung

Intel

Intel R1000WF Series Bedienungsanleitung

Intel

Intel IP Network server NSI2U Bedienungsanleitung

Intel

Intel AC450NX Bedienungsanleitung

Intel

Intel SR1630GP - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel M50FCP1UR Bedienungsanleitung

Intel

Intel JBOD 2000 Family Bedienungsanleitung

Intel

Intel P4000M Bedienungsanleitung

Intel

Intel P4304SC2SFEN Bedienungsanleitung

Intel

Intel SC5650HCBRP Einrichtungshandbuch

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung