Intel R2000LH2 Bedienungsanleitung

Optical

Device

Assembly

Thank you for buying an Intel® Server System. The following information will help you

assemble your Intel®Server System and install components.

If you are not familiar with ESD [Electrostatic Discharge] procedures used during

system integration, see the complete ESD procedures described in your Service Guide.

This guide and other supporting documents are located on the web at:

http://www.intel.com/support.

G54804-003

Intel® Server System R2000LH2/LT2

Product Family

Quick Installation User's Guide

*3.5" hard drive bay system as shown

(This page is intentionally left blank.)

Table of Contents

General Installation Process ........................................................................................................ 2

Reference .......................................................................................................................................... 12

System Overview .............................................................................................................................. 1

Preparing System ................................................................................................................ 2

Remove Power Supply Module .................................................................................... 2

Remove Top Cover.............................................................................................................. 2

Remove Add-in Card Riser Assembly ...................................................................... 2

Remove Air Duct .................................................................................................................. 2

Remove Processor Heatsink(s) .................................................................................... 3

Install Processor(s).............................................................................................................. 3

Install Processor Heatsink(s) ........................................................................................ 4

Install Memory Modules .................................................................................................. 4

Install Hard Drives .............................................................................................................. 5

Install Optical Drive ............................................................................................................ 8

Install Intel® I/O Expansion Module (optional) ...................................................... 8

Install Intel® RAID C600 Upgrade Key (optional) ................................................ 8

Install Air Duct ...................................................................................................................... 9

Install Add-in Card(s) .......................................................................................................... 9

Install Add-in Card Riser Assembly ..........................................................................10

Install Intel® RAID Smart Battery (optional) ........................................................10

Install Top Cover ................................................................................................................10

Install Power Supply Module ......................................................................................10

Finishing Up ..........................................................................................................................11

Software ................................................................................................................................11

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://www.intel.com/support/

motherboards/server/sb/cs-010770

.htm for complete safety information.

Warning

Installation and service

of this product to be

performed only by

qualiﬁed service personnel

to avoid risk of injury from

electrical shock or energy

hazard.

Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to server board and/or

other components.

Tools Required

Anti-static

wrist strap

Phillips*

screwdriver

Intel®is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as

Thermal Operation and Conﬁguration Requirements

To keep the system operating within supported maximum thermal limits, the system must meet the following operating and

conﬁguration guidelines:

• Ambient inlet temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time.

Doing so may affect long term reliability of the system.

• The CPU-1 processor and CPU heatsink must be installed ﬁrst. The CPU-2, CPU-3, and CPU-4 heatsink must

be installed at all times, with or without a processor installed.

• Memory Slot population requirements:

NOTE: Speciﬁed memory slots either can be populated with a DIMM or supplied DIMM Blank. Memory population

rules apply when installing DIMMs.

▪ DIMM Population Rules on CPU-1

Install DIMMs in order; Channels A, B, C, and D. Start with ﬁrst DIMM slot (blue) on each channel, then slot 2, then

slot 3. Remove only DIMM blanks when populating the slot with a DIMM.

▪ DIMM Population Rules on CPU-2

Install DIMMs in order; Channels E, F, G, and H. Start with ﬁrst DIMM slot (blue) on each channel, then slot 2, then

slot 3. Remove only DIMM blanks when populating the slot with a DIMM.

▪ DIMM Population Rules on CPU-3

Install DIMMs in order; Channels J, K, L, and M. Start with ﬁrst DIMM slot (blue) on each channel, then slot 2, then

slot 3. Remove only DIMM blanks when populating the slot with a DIMM.

▪ DIMM Population Rules on CPU-4

Install DIMMs in order; Channels N, P, R, and T. Start with ﬁrstDIMM slot (blue) on each channel, then slot 2, then

slot 3. Remove only DIMM blanks when populating the slot with a DIMM.

• All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied

drive blank.

• The air duct must be installed at all times.

• In single power supply conﬁgurations, the second power supply bay must have the supplied ﬁller blank installed

at all times.

• The system top-cover must be installed at all times. The only exception to this requirement is to hot replace

a failed system fan, in which case the top cover can be removed for no more than three minutes at a time.

System Overview

Intel® Server System R2000LH2/LT2 Product Family

Useful Information:

• The SCU1 (4-7) port requires an Intel® RAID C600 Upgrade Key installed to be functional.

Optical

Device

Assembly

Hard Drive Bays

System Fans

CPU2

CPU 3

Add-in Card Riser Assembly

1+1 Redundant Power Supply Modules

Server Board

Air Duct

Optical Drive Bay

Front Control Panel

CPU1

CPU4

System Features and Components

Airduct

*3.5" Hard Drive Bay system as shown

General Installation Process

The installation instructions in this section are for common components of Intel® Server System

R2000LH2/LT2 Product Family.

Minimum Hardware Requirements

•Memory Type:

Minimum of one 512MB DDR3 1066/1333 MHz UDIMM or one 1GB

DDR3 1066/1333 MHz RDIMM.

•Processor:

Intel® Xeon® processor E5-4600 product family.

•Hard Disk Drives: SATA

For a complete list of compatible processors, heatsinks, and memory, see

http://www.intel.com/support.

To avoid integration difﬁculties and possible board damage, your system must

meet the following minimum requirements:

Preparing System

Observe normal ESD (Electrostatic Discharge)

procedures.

Place your Intel®Server System on a ﬂat anti-static

surface to perform the following integration procedures.

Observe ESD procedures before reaching inside to make

server board connections or install components.

CAUTION:

Unplug all

AC power cords

and remove all

power supply

modules before

lifting tilt bay.

Lift up the

tilt bay.

Bend and

slide out

the air duct.

Remove the air duct from

the chassis.

Optical

Device

Assembly

Remove Air Duct

Optical

Device

Assembly

Remove Top Cover

Remove three screws.

Slide cover back and lift upward.

Remove Add-in Card Riser Assembly

Pull up the release lever of the

riser assembly.

Grasp the riser assembly with

both hands and pull up to

remove from system.

CAUTION: Place the

riser assembly upside

down or sideways to

avoid damage to the riser card

connector.

Remove Power Supply Module

Push the green

latch to unlock the

power supply.

While pushing the

green latch, pull

the power supply

out of the system

by the handle.

Repeat step A and

B to remove the

second power

supply.

General Installation Process

Install Processor(s) ...continued

D. Install the Processor

CAUTION: The bottom side of the processor has

components that may damage the socket pins

if installed wrongly.

Processor must align correctly with the

socket opening before installation.

DO NOT DROP processor into socket! Components

Take the processor out of the

box and remove the

protective shipping cover.

CAUTION: When

unpacking a processor,

hold at the edges only

to avoid touching the

golden contact pins.

Save the protective

cover.

Note the location of the golden

key at the corner of the

processor.

Orient the processor with the

socket so that the processor

cutouts match the four

orientation posts on the socket.

IMPORTANT!

Before proceeding

further, check your

Intel®Server System

for disconnected or

loose cables and

components that

may have occurred

during shipping.

6Remove Processor Heatsink(s)

The heatsink is attached to the server board and/or processor socket with captive fasteners.

Lift the heatsink straight up.

CAUTION: The heatsink has thermal interface material (TIM) on the underside

of it. Use caution so that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

Using a #2 Phillips* screwdriver, loosen the four screws located on the

heatsink corners in a diagonal manner using the following procedure:

Using a #2 Phillips* screwdriver, start with screw 1 and loosen it by

giving it two rotations and stop. (IMPORTANT: Do not fully loosen.)

Proceed to screw 2 and loosen it by giving it two rotations and stop.

Similarly, loosen screws 3 and 4.

Repeat steps A and B by giving each screw two rotations each time

until all screws are loosened.

OPEN 1st

CLOSE 1st

NO CPU

Processor

Socket

7Install Processor(s)

A. Remove the Cover C. Open the Load Plate

B. Open the Socket Lever

Repeat step A to

release the lever

on the other side.

Push down the lever handle on the

OPEN 1st side and away from the

socket to release it.

BOpen the load plate all the way.

Press the locking lever slightly to raise

the load plate.

ARemove the cover

as shown

NOTE: Release

the levers in the

order as shown.

FOXCONN LGA2011 ILM 17562

OPEN 1st

NO CPU

OPEN 1st

FOXCONN LGA2011 ILM 17562

Carefully lower the load plate over

the processor.

E. Close the Load Plate

General Installation Process

9Install Memory Modules

DDR3 DIMM Memory Identiﬁcation:

Other

Memory

DDR3

CAUTION: Observe normal ESD (ElectroStatic

Discharge) procedures to avoid possible damage to

system components.

DIMM notch and socket bump must align as shown below.

8Install Processor Heatsink(s)

NOTE: Heatsink styles may vary.

Remove the protective ﬁlm on the TIM if present.

CAUTION: The heatsink has thermal interface

material (TIM) on the underside of it. Use caution so

that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

BAlign heatsink ﬁns to the front and back of

the chassis for correct airﬂow.

Airﬂow goes from front-to-back of chassis.

Each heatsink has four captive fasteners and

should be tightened in a diagonal manner using

the following procedure:

Using a #2 Phillips* screwdriver,

start with screw 1 and engage screw

threads by giving it two rotations

and stop. (Do not fully tighten.)

Proceed to screw 2 and engage screw

threads by giving it two rotations and

stop. Similarly, engage screws 3 and 4.

Repeat steps C and D by giving each

screw two rotations each time until

each screw is lightly tightened up to

a maximum of 8 inch-lbs torque.

OPEN 1st

CLOSE 1st

Processor

Socket

AIRFLOW

Chassis Front

TIM

CAUTION:

Do not

over-tighten

fasteners.

CPU 1 SocketCPU 2 Socket

CPU 4 SocketCPU 3 Socket

DIMM_E1

DIMM_E2

DIMM_E3

DIMM_F1

DIMM_F2

DIMM_F3

DIMM_L1

DIMM_L2

DIMM_L3

DIMM_M1

DIMM_M2

DIMM_M3

DIMM_J1

DIMM_J2

DIMM_J3

DIMM_K1

DIMM_K2

DIMM_K3

DIMM_R1

DIMM_R2

DIMM_R3

DIMM_T1

DIMM_T2

DIMM_T3

DIMM_N1

DIMM_N2

DIMM_N3

DIMM_P1

DIMM_P2

DIMM_P3

DIMM_G1

DIMM_G2

DIMM_G3

DIMM_H1

DIMM_H2

DIMM_H3

DIMM_C1

DIMM_C2

DIMM_C3

DIMM_D1

DIMM_D2

DIMM_D3

DIMM_A1

DIMM_A2

DIMM_A3

DIMM_B1

DIMM_B2

DIMM_B3

Install Memory Modules ...continued

Memory Conﬁgurations and Population Order:

For best performance, a minimum of four DIMMs per CPU is

recommended, populated in the blue slot of each memory channel.

In a single-processor conﬁguration, always populate A1 DIMM ﬁrst.

In a four-processor conﬁguration, always populate A1 DIMM for CPU1, E1

DIMM ﬁrst for CPU2, J1 for CPU3, and N1 for CPU4.

NOTE: For additional memory conﬁgurations, see the Service Guide

available at http://www.intel.com/p/en_US/support.

Memory sizing and conﬁguration is supported only for qualiﬁed DIMMs

approved by Intel®. For a list of supported memory, go to:

http://serverconﬁgurator.intel.com.

Intel® Server Board S4600LH2/LT2

Install Processor(s) ...continued

Push down on the locking lever on the CLOSE 1st side.

F. Latch the Locking Lever

BSlide the tip of the lever under the notch in the load plate.

Make sure the load plate tab engages under the socket lever when

fully closed.

CRepeat the steps to latch the locking lever on the other side.

OPEN 1st

CLOSE 1st

REMOVE

CLOSE 1st

OPEN 1st

CLOSE 1st

NOTE: Latch the levers in the

order as shown.

General Installation Process

Install Memory Modules ...continued

To Install DIMMs:

Open both DIMM socket levers.

Note location of alignment notch.

CAUTION: Avoid touching contacts

when handling or installing DIMMs.

IMPORTANT! Visually check that each latch is fully closed and correctly engaged with

each DIMM edge slot.

Push down ﬁrmly on the DIMM until it snaps into place and both levers close.

Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.

135

0467

10 Install

Hard Drives

2.5" Hard Drive Carrier (For system with 2.5" hard drive bay only)

Hard Drive Numbering Diagram

Drive 0 Primary 8 x 2.5" hard drive bay as shown

Press the

green

latch to

unlock.

Pull out the black lever and slide

the carrier out.

Remove the four screws securing the plastic drive blank

from the 2.5" HDD carrier.

Disengage the plastic drive blank from the HDD carrier.

Remove the plastic drive blank from the 2.5" HDD carrier.

Install the hard disk drive using the four screws as shown.

Make sure the connector end of the drive matches the

backplane connector.

With the lever open, insert the hard disk drive

assembly into the chassis, then push in the lever

to lock it into place.

CAUTION: If you don't install

all drives, empty drive bays

must be occupied by carriers

with plastic drive blank

provided to maintain proper

system cooling.

2.5" HDD

General Installation Process

2.5" HDD

Install

Hard Drives ...continued

3.5" Hard Drive Carrier (For system with 3.5" hard drive bay only)

Remove the drive carrier

by pressing the green

button and opening the

lever.

d2 d3

Slide the carrier out.

Remove the four

screws securing the

HDD interface bracket

and remove the HDD

interface bracket.

Install the HDD interface bracket

from top. Secure the bracket with

three screws as shown.

Slide the 2.5" HDD into the

bracket to align the screw holes

with the right and left rail.

Break off the tab on the

HDD interface bracket.

Install 2.5" Hard Drive as option:

Secure the hard disk drive using

the four screws for 2.5" HDD.

Install the hard disk drive using

the same four screws as shown.

Make sure the connector end of

the drive matches the backplane

connector.

With the lever open, insert the hard disk drive assembly into

the chassis.

Push in the lever to lock

it into place.

Bottom

View

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

CAUTION: If you don't install all drives, empty drive bays must be

occupied by carriers with plastic drive blank provided to maintain

proper system cooling.

2.5" HDD

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

Optical

Device

Assembly

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

Optical

Device

Assembly

3.5´´ HDD

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

Hard Drive Numbering Diagram

Drive 0 Primary 4 x 3.5’’ hard drive bay as shown

0 1 2 3

Andere Handbücher für R2000LH2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intel Server Handbücher

Intel

Intel SR1670HV - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1625UR - Server System - 0 MB RAM Konfigurationshandbuch

Intel

Intel R2000LH2 Bedienungsanleitung

Intel

Intel NSC2U - IP Network Server Bedienungsanleitung

Intel

Intel R2600SR Series Bedienungsanleitung

Intel

Intel STCK1A32WFC Bedienungsanleitung

Intel

Intel AC450NX Bedienungsanleitung

Intel

Intel S2600TP series Bedienungsanleitung

Intel

Intel R2000SC Bedienungsanleitung

Intel

Intel SR1600UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel P4000RP Bedienungsanleitung

Intel

Intel S7000FC4UR - Server System - 0 MB RAM Konfigurationshandbuch

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel R1000GL Bedienungsanleitung

Intel

Intel SR1560SF - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SC5400RA - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1530AHLX - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1695WB Bedienungsanleitung

Intel

Intel R1000SPO series Konfigurationshandbuch

Intel

Intel SR2625UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel M20NTP1UR Kurzanleitung zur Einrichtung

Intel

Intel Dialogic Bedienungsanleitung

Intel

Intel SC5650BCDP Konfigurationshandbuch

Intel

Intel SRPL8 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung