Intel R1000GL Bedienungsanleitung

Thank you for buying an Intel® Server System. The following information will help you

assemble your Intel®Server System and install components.

If you are not familiar with ESD [Electrostatic Discharge] procedures used during

system integration, see the complete ESD procedures described in your Service Guide.

This guide and other supporting documents are located on the web at:

http://www.intel.com/support.

G31060-004

Intel® Server System R1000GZ/GL

Product Family

Quick Installation User's Guide

* 2.5" hard drive bay system as shown

(This page is intentionally left blank.)

Table of Contents

General Installation Process ........................................................................................................ 2

Reference ............................................................................................................................................ 11

System Overview .............................................................................................................................. 1

Preparing the System ...................................................................................................... 2

Remove the Top Cover .................................................................................................... 2

Remove the Air Duct ........................................................................................................ 2

Remove Processor Heatsink(s) ................................................................................... 2

Install the Processor(s) .................................................................................................. 3

Install Processor Heatsink(s) ....................................................................................... 4

Install Memory Modules .................................................................................................. 4

Install Hard Drives .............................................................................................................. 5

Install Optical Drive ............................................................................................................ 7

Install the Air Duct ............................................................................................................. 7

Remove Add-in Card Riser Assembly ...................................................................... 7

Install Add-in Card(s) ......................................................................................................... 7

Install Add-in Card Riser Assembly ........................................................................... 8

Install Rack Handles .......................................................................................................... 8

Install Intel® I/O Expansion Module (optional) ..................................................... 8

Install Intel® RAID C600 Upgrade Key (optional) ............................................... 8

Install Intel® RAID Smart Battery (optional) ......................................................... 8

Install Second Power Supply Module (optional) ................................................. 9

Install Bezel (optional) ...................................................................................................... 9

Install the Top Cover ........................................................................................................... 9

Finishing Up ............................................................................................................................. 9

Software ............................................................................................................................... 10

Warning

Read all caution and safety

statements in this document

before performing any of the

instructions. Also see the Intel

Server Board and Server Chassis

Safety Information document at:

http://www.intel.com/support/

motherboards/server/sb/cs-010770

.htm for complete safety information.

Warning

Installation and service

of this product to be

performed only by

qualified service personnel

to avoid risk of injury from

electrical shock or energy

hazard.

Caution

Observe normal ESD

[Electrostatic Discharge]

procedures during system

integration to avoid possible

damage to server board and/or

other components.

Tools Required

Anti-static

wrist strap

Phillips*

screwdriver

Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the

Thermal Operation and Conﬁguration Requirements

To keep the system operating within supported maximum thermal limits, the system must meet the following operating and

configuration guidelines:

• Ambient inlet temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time.

Doing so may affect long term reliability of the system.

• The CPU-1 processor + CPU heatsink must be installed first. The CPU-2 heatsink must be installed at all times,

with or without a processor installed.

• Memory Slot population requirements:

NOTE: Specified memory slots can be populated with a DIMM or supplied DIMM Blank. Memory population rules apply

when installing DIMMs.

– DIMM Population Rules on CPU-1

Install DIMMs in order: Channels A, B, C, and D. Start with 1st DIMM slot (blue) on each channel, then slot 2, then

slot 3 (24 DIMM board). Only remove DIMM blanks when populating the slot with a DIMM.

– DIMM Population on CPU-2

Install DIMMs in order: Channels E, F, G, and H. Start with 1st DIMM slot (blue) on each channel, then slot 2, then

slot 3 (24 DIMM board). Only remove DIMM blanks when populating the slot with a DIMM.

The following system configurations require the specific memory slots be populated at all times using a DIMM or

supplied DIMM blank.

– System Conﬁguration: 8x 2.5" hard drive bay configuration + 24 DIMM server board

DIMM blanks installed on memory slot 3 for all memory channels.

• All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied

drive blank.

• The air duct must be installed at all times.

• In single power supply configurations, the second power supply bay must have the supplied filler blank installed

at all times.

• The system top-cover must be installed at all times. The only exception to this requirement is to hot replace a failed

system fan, in which case the top cover can be removed for no more than three minutes at a time.

System Overview

* 2.5" Hard Drive Bay system as shown

System Features and Components

Hot Swap

Hard Drive Bays

CPU2

Air Duct

Front Control Panel

PCI Riser

1+1 Redundant

Power Supply

Modules

Server Board

System Fans

CPU1

Intel® Server System R1000GZ/GL Product Family

Useful Information:

• Riser Slot 2 is not functional without having two processors installed.

• The SCU1 (4-7) port requires an Intel® RAID C600 Upgrade Key installed to be functional.

General Installation Process

The installation instructions in this section are for common components of Intel® Server System

R1000GZ/GL Product Family.

Minimum Hardware Requirements

•Memory Type:

Minimum of one 512MB DDR3 1066/1333 MHz UDIMM or one 1GB

DDR3 800/1066/1333/1600 MHz RDIMM.

•Processor:

Intel® Xeon® processor E5-2600 product family.

•Hard Disk Drives: SATA

For a complete list of compatible processors, heatsinks, and memory, see

http://www.intel.com/support.

To avoid integration difﬁculties and possible board damage, your system must

meet the following minimum requirements:

Preparing the System

Observe normal ESD (Electrostatic Discharge)

procedures.

Place your Intel®Server System on a ﬂat anti-static

surface to perform the following integration procedures.

Observe ESD procedures before reaching inside to make

server board connections or install components.

IMPORTANT!

Before proceeding

further, check your

Intel®Server System

for disconnected or

loose cables and

components that

may have occurred

during shipping.

Remove the Air Duct

Remove the air duct by

lifting straight up.

Remove the Top Cover

Remove the four screws.

Slide cover back and lift upward.

Remove Processor Heatsink(s)

The heatsink is attached to the server board/processor socket with captive fasteners.

Lift the heatsink straight up.

CAUTION: The heatsink has thermal interface material (TIM) on the underside

of it. Use caution so that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

Using a #2 Phillips* screwdriver, loosen the four screws located on the

heatsink corners in a diagonal manner using the following procedure:

Using a #2 Phillips* screwdriver, start with screw 1 and loosen it by

giving it two rotations and stop. (IMPORTANT: Do not fully loosen.)

Proceed to screw 2 and loosen it by giving it two rotations and stop.

Similarly, loosen screws 3 and 4.

Repeat steps A and B by giving each screw two rotations each time

until all screws are loosened.

Processor

Socket

General Installation Process

Install the Processor(s) ... continued

C. Install the Processor

Take the processor out of the box and remove the protective shipping cover.

CAUTION: When unpacking a processor,

hold by the edges only to avoid touching

the gold contact pins.

Save the

protective

cover.

CAUTION: The underside of the processor has

components that may damage the socket pins

if installed improperly.

Processor must align correctly with the socket opening before installation.

DO NOT DROP processor into socket!

Components

Note location of gold key at corner of processor.

Orient the processor with the socket so that the processor cutouts match the four orientation

posts on the socket.

OPEN 1st

CLOSE 1st

NO CPU

Install the Processor(s)

A. Open the Socket Lever B. Open the Load Plate

BRepeat step A to release the lever on the other side.

Push down the lever and slide away from the socket to

release it. A

BOpen the load plate all the way.

Press the locking lever slightly to raise the

load plate.

NOTE: Release

the levers in the

order as shown.

OPEN 1st

FOXCONN LGA2011 ILM 17562

NO CPU

Save the

protective

cover.

Install the Processor(s) ... continued

D. Remove the Cover

Press the cover to

remove it. Carefully lower the load plate over

the processor.

E. Close the Load Plate

Push down the locking lever.

F. Latch the Locking Lever

BSlide the tip of the lever under the notch in the load plate.

Make sure the load plate tab engages under the socket lever

when fully closed.

CRepeat the steps to latch the locking lever on the other side.

NOTE: Latch the levers in

the order as shown.

FOXCONN LGA2011 ILM 17562

General Installation Process

7Install Memory Modules

DDR3 DIMM Memory Identiﬁcation:

Other

Memory

DDR3

CAUTION: Observe normal ESD (ElectroStatic

Discharge) procedures to avoid possible damage to

system components.

DIMM notch and socket bump must align as shown below.

Install Memory Modules ... Continued

Memory Conﬁgurations and Population Order:

Intel® Server Board S2600GZ

For best performance, a minimum of four DIMMs per CPU is recommended, populated in the blue slot of each memory channel.

In a single-processor conﬁguration, always populate A1 DIMM ﬁrst.

In a dual-processor conﬁguration, always populate A1 DIMM ﬁrst for CPU1 and E1 DIMM ﬁrst for CPU2.

Note: For additional memory conﬁgurations, see the Service Guide on the Intel®Server Deployment & Management DVD that accompanied your Intel®

Server System, or go to: http://www.intel.com/support.

Memory sizing and conﬁguration is supported only for qualiﬁed DIMMs approved by Intel. For a list of supported memory, go to:

http://serverconﬁgurator.intel.com.

CPU2 SocketCPU1 Socket

DIMM_C1

DIMM_C2

DIMM_C3

DIMM_D1

DIMM_D2

DIMM_D3

DIMM_G1

DIMM_G2

DIMM_G3

DIMM_H1

DIMM_H2

DIMM_H3

DIMM_B3

DIMM_B2

DIMM_B1

DIMM_A3

DIMM_A2

DIMM_A1

DIMM_F3

DIMM_F2

DIMM_F1

DIMM_E3

DIMM_E2

DIMM_E1

6Install Processor Heatsink(s)

NOTE: Heatsink styles may vary.

Remove the protective ﬁlm on the TIM if present.

CAUTION: The heatsink has thermal interface

material (TIM) on the underside of it. Use caution so

that you do not damage the thermal interface material.

Use gloves to avoid sharp edges.

BAlign heatsink ﬁns to the front and back of

the chassis for correct airﬂow.

Airﬂow goes from front-to-back of chassis.

Each heatsink has four captive fasteners and

should be tightened in a diagonal manner using

the following procedure:

Using a #2 Phillips* screwdriver,

start with screw 1 and engage screw

threads by giving it two rotations

and stop. (Do not fully tighten.)

Proceed to screw 2 and engage screw

threads by giving it two rotations and

stop. Similarly, engage screws 3 and 4.

Repeat steps C and D by giving each

screw two rotations each time until

each screw is lightly tightened up to

a maximum of 8 inch-lbs torque.

Processor

Socket

AIRFLOW

Chassis Front

TIM

CAUTION:

Do not

over-tighten

fasteners.

General Installation Process

Install Memory Modules ... Continued

To Install DIMMs:

Open both DIMM socket levers.

Note location of alignment notch.

CAUTION: Avoid touching contacts

when handling or installing DIMMs.

IMPORTANT! Visually check that each latch is fully closed and correctly engaged with

each DIMM edge slot.

Push down ﬁrmly on the DIMM until it snaps into place and both levers close.

Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.

2.5" HDD

8Install

Hard Drives

2.5" Hard Drive Carrier (For system with 2.5" hard drive bay only)

Hard Drive Numbering Diagram

Drive 0 Primary

8 x 2.5" hard drive bay as shown

Remove the drive carrier by pressing the

green

latch

to unlock.

Pull out the black lever and slide the carrier out.

Remove the four screws from the 2.5" HDD carrier.

Disengage and remove the plastic drive blank

from the HDD carrier.

Install the hard disk drive using the four screws as shown. Make sure

the connector end of the drive matches the backplane connector.

With the lever open, insert the hard disk drive assembly into the chassis,

then push in the lever to lock it into place.

CAUTION: If you don't install

all drives, empty drive bays

must be occupied by carriers

with plastic drive blank

provided to maintain proper

system cooling.

General Installation Process

2.5" HDD

Install

Hard Drives ... Continued

3.5" Hard Drive Carrier (For system with 3.5" hard drive bay only)

Hard Drive Numbering Diagram

Drive 0 Primary

Remove the drive carrier by pressing the green button and opening

the lever.

Slide the carrier out.

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

Remove the four screws securing the HDD interface bracket and remove

the HDD interface bracket.

Install 2.5" Hard Drive as option:

3.5´´ HDD

Install the hard disk drive using the same four screws as shown. Make

sure the connector end of the drive matches the backplane connector.

With the lever open, insert the hard disk drive assembly into the chassis.

Push in the lever to lock it into place.

4 x 3.5’’ hard drive bay as shown

CAUTION: If you don't install

all drives, empty drive bays

must be occupied by carriers

with plastic drive blank

provided to maintain proper

system cooling.

d1 d4

d2 d3

Install the HDD interface bracket

from top. Secure the bracket with

three screws as shown.

Slide the 2.5" HDD into the

bracket to align the screw holes

with the right and left rail.

Break off the tab on the

HDD interface bracket.

Secure the hard disk drive using

the four screws for 2.5" HDD.

Bottom

View

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

TOP

BREAK OFF TAB

BEFORE MOUTING

2.5´´ HARD DRIVE

0 1 2 3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intel Server Handbücher

Intel

Intel SC5400RA - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel R1000BB Family Bedienungsanleitung

Intel

Intel SR2612UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel P4304SC2SFEN Bedienungsanleitung

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel R1000WF Series Kurzanleitung zur Einrichtung

Intel

Intel S7000FC4UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel IP Media Server Bedienungsanleitung

Intel

Intel SBX44 - Server Compute Blade Bedienungsanleitung

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel R2000WF series Konfigurationshandbuch

Intel

Intel SR2600UR - Server System - 0 MB RAM Bedienungsanleitung

Intel

Intel SC5650HCBRP Bedienungsanleitung

Intel

Intel H2000WP Bedienungsanleitung

Intel

Intel SBXD62 - Server Compute Blade Bedienungsanleitung

Intel

Intel SR870BN4 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel ISP1100 - Server Platform - 0 MB RAM Bedienungsanleitung

Intel

Intel SR1530AHNA Konfigurationshandbuch

Intel

Intel SR1695WB Bedienungsanleitung

Intel

Intel MFSYS25V2 Bedienungsanleitung

Intel

Intel AD450NX Bedienungsanleitung

Intel

Intel SRPL8 Bedienungsanleitung

Intel

Intel S7000FC4UR - Server System - 0 MB RAM Konfigurationshandbuch

Intel

Intel R2000BB series Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung