Intellinet 524780, 524797, 524872, 524896 Bedienungsanleitung

Wireless

300N ADsl2+

MoDeM

router

quick

iNstAll

guiDe

MODELS:

524780

524797

INT-524780/524797-QIG-1209-01

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™

Wireless 300N ADSL2+ Modem Router, Model 524780 (Annex A) or

Model 524797 (Annex B).

This quick install guide presents the basic steps required to set up and

operate this device. For detailed instructions, specications and regulatory/

compliance statements, refer to the user manual on the enclosed CD or

at www.intellinet-network.com. Easy-to-follow instructions in this guide

and the user manual help make installation quick and simple, so you’ll

soon be enjoying the benets of its many features:

• 2T2R MIMO technology for enhanced throughput and coverage

• Supports ADSL standards G.992.1 (G.dmt), G.992.2 (G.lite), G.992.3

(ADSL2), G.992.4 (splitterless ADSL2), G.992.5 (ADSL2+) for Annex A

• Supports 24 Mbps ADSL2+ downstream data rate

• Supports Wi-Fi Protected Setup (WPS)

• Supports WEP and WPA/WPA2 (TKIP and AES) data encryption

• Integrated 10/100 Mbps LAN switch with Auto MDI/MDI-X support

• DHCP server assigns IP addresses for all LAN users

• DHCP server supports static lease management

• Supports port forwarding, DMZ (demilitarized zone), DDNS (dynamic

DNS), UPnP (Universal Plug and Play), SNMP management

• Integrated SPI rewall

• QoS (Quality of Service) bandwidth management

• VPN Pass Through (PPTP, IPSec, L2TP)

• Complies with 2.4 GHz Draft IEEE 802.11n standard and is backward

compatible with IEEE 802.11g/b standards

• Easy installation through Web-based user interface

• System status, security log, rmware upgradeable

• Lifetime Warranty (except where limited — see package)

Package Contents

• Wireless 300N ADSL 2+ Modem Router

• Quick installation guide

• Setup CD with user manual and setup wizard

• Power adapter

• Ethernet Cat5 RJ45 cable, 1.0 m (3 ft.)

• RJ11 telephone cable, 1.8 m (5.9 ft.)

hArDWAre setup/coNNectioNs

1. Connect the router to your ADSL cable using the supplied RJ11 cable.

2. Connect the router to your PC, hub or switch by attaching the Ethernet

cable to the LAN port of the router.

3. Connect the power adapter to the power jack on the rear panel of

the router.

4. The ADSL LED will be on if the router is connected to the ADSL cable

and receives the ADSL signals successfully. If the LED is blinking,

contact your ISP (Internet service provider) to check the problem.

NOTE: Use only the power adapter included with the router, and not any

other power adapter.

setup WizArD

This router provides a Setup Wizard for conguring the ADSL settings.

This wizard collects some ISPs’ ADSL settings so that you can easily

congure the router’s ADSL settings just by selecting the ISP vendor

from the wizard. If you can’t nd your ISP from the list in the wizard,

manually set the ISP information. Both procedures are presented below.

Getting Started

Before starting, check the following items:

• Make sure you’ve connected the ADSL cable to the router correctly.

When the ADSL cable is worked normally, the ADSL LED will be on.

• Un-install any dial-up programs installed previously for the USB modem

or other dial-up devices.

• It’s recommended that you initially congure the router through the

Ethernet cable before you set the wireless functions.

This wizard can be run in Windows 98SE/Me/2000/XP/Vista. The

following procedures are operated in Windows XP. (Procedures are

similar for Windows 98SE/Me/2000/Vista.)

1. Insert the enclosed setup CD into your CD-ROM drive. The

Autorun.exe program should be executed automatically. If not, run

Autorun.exe manually from the “Autorun” folder on the CD.

2. The following screen will be displayed. Click “Setup Wizard.”

3. The wizard will run and try to search for the router. If the router is

found, the wizard will guide you to Step 5.

4. If the router can’t be found, enter the IP address and the password

of the router to search again. Click “Next” to continue.

5. The wizard will automatically select the country you’re in by checking

the language of the operating system in your computer and then

advance to the Select ISP screen. Select the ISP. If you can’t nd

the ISP, click “Other” to reselect the country or manually congure

the ISP information.

Setting the ISP Automatically

If you can nd the ISP from the wizard, follow the steps below to let the

wizard set the ISP settings automatically.

1. Select the ISP of your ADSL service.

2. Enter the username and password your ISP has provided, if needed.

Click “Next.”

3. Click “Save” to save the settings and reboot the router.

4. After saving and rebooting the router, the ISP settings are done. The

wizard will then help to set your computer to obtain an IP address from

the router automatically. A screen with a status bar will display to

indicate the progress of the procedure.

NOTE 1: To use the router to access the Internet, the IP address of each

PC needs to be set in the same network segment as the router. The

wizard will help to set the proper IP address for your computer.

NOTE 2: By default, the router’s DHCP server is enabled. If it’s disabled

before running the wizard, the wizard will enable the DHCP server

automatically.

5. The wizard will attempt to connect to the ISP you’ve selected. If the

connection fails, a screen prompt will display to indicate this is the

case. Run the wizard to select the ISP again.

6. If you do successfully connect to the ISP, you’ll see the screen below.

To congure additional settings, click “Advanced Settings” to go the

Web management of the router, or click “Finish” to close the wizard.

Setting the ISP Manually

If you can’t nd the ISP from the wizard, follow the steps below to set the

ISP settings manually.

First, check with your ISP (Internet service provider) as to what kind of

service is provided, such as PPPoE, PPPoA or RFC1483/2684. Gather

the information as illustrated in the table below and keep it for reference.

PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username,

Password (and Service Name).

PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username,

Password.

RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use

Bridged Mode.

RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, IP Address,

Subnet Mask, Gateway Address, and Domain Name

System (DNS) IP Address (a xed IP address).

1. Select “Other.”

2. Check with your ISP as to the connection type of the ADSL line. Select

the Connection Type and click “Next.”

NOTE: The wizard will automatically select the country you’re in by

checking the language of the operating system in your computer and

then skip to the Select ISP screen. If you want to change the country,

click “Back” here.

3. Input the VPI, VCI and encapsulation data supplied by your ISP. If the

Connection Type is “Static IP Address,” you need to input the IP

address information supplied by your ISP. For details about each

setting, refer to Section 5.2 in the user manual.

4. Enter the username and password that your ISP has provided, if

needed. Click “Next.”

Andere Handbücher für 524780, 524797, 524872, 524896

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intellinet Netzwerk-Router Handbücher

Intellinet

Intellinet 524803 Bedienungsanleitung

Intellinet

Intellinet 560559 Bedienungsanleitung

Intellinet

Intellinet 522595 Bedienungsanleitung

Intellinet

Intellinet 516204 Bedienungsanleitung

Intellinet

Intellinet 561457 Bedienungsanleitung

Intellinet

Intellinet 530347 Bedienungsanleitung

Intellinet

Intellinet 560535 Bedienungsanleitung

Intellinet

Intellinet 560559 Bedienungsanleitung

Intellinet

Intellinet Network Solutions 523462 Bedienungsanleitung

Intellinet

Intellinet 560535 Bedienungsanleitung

Intellinet

Intellinet 560849 Bedienungsanleitung

Intellinet

Intellinet 524988 Bedienungsanleitung

Intellinet

Intellinet 505093 Bedienungsanleitung

Intellinet

Intellinet 560405 Bedienungsanleitung

Intellinet

Intellinet 523493 Bedienungsanleitung

Intellinet

Intellinet 561051 Bedienungsanleitung

Intellinet

Intellinet 521246 Bedienungsanleitung

Intellinet

Intellinet 524636 Bedienungsanleitung

Intellinet

Intellinet 523523 Bedienungsanleitung

Intellinet

Intellinet 524803 Bedienungsanleitung

Intellinet

Intellinet 523646 Bedienungsanleitung

Intellinet

Intellinet 560931 Bedienungsanleitung

Intellinet

Intellinet 530347 Bedienungsanleitung

Intellinet

Intellinet 523813 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung