Intermec Trakker Antares 2400 Bedienungsanleitung

Charging the Terminal Batteries

The adapter will trickle charge the lithium-ion

battery pack and the NiCad backup battery.

The lithium-ion battery pack and the NiCad

backup battery will be fully charged within 18

hours.

Note: The external power supply must

be connected to the terminal to charge

the lithium-ion battery pack and the

NiCad backup battery.

Transmitting and Receiving Data

1. Connect the adapter to the terminal.

2. Connect the device (host computer, printer,

or modem) to the adapter serial port.

3. Turn on the terminal and the device.

4. Start your program on the terminal or the

device.

Data begins transmitting between the terminal

and the device.

Troubleshooting

If communications through the adapter are not

working, check to make sure

the baud rate settings for the terminal match

the baud rate settings for the connected

device.

you are using the correct serial cable.

there is power at the electrical outlet or you

have a fully charged battery pack in the

terminal.

Specifications

Electrical requirements

10V

Interface 9-pin, RS-232 connector

Optical interface 2 IR receivers and 2 IR

transmitters

Optical RS-232 interface Converted RS-232 bipolar

signals to optical signals and

vice versa

Interface speeds RS-232 baud rate up to

38,400 bps

Operating temperature

and humidity

-20

C to 50

C (-4

F to 122

F),

0 to 95%, non-condensing

Charging temperature 0

C to 50

C (32

F to 122

Storage temperature

and humidity

-20

C to 70

C (-4

F to 158

F),

0 to 95%, non-condensing

Note: The terminal lithium-ion battery pack

will not charge below 0

C (32

F).

Design and specifications are subject to change without

notice.

Trakker Antares

Optical Link Adapter

Quick Reference Guide

The Trakker Antares optical link adapter (Part

No. 064021) is an accessory for the Trakker

Antares terminals. The optical link adapter can

transmit data between a terminal and

another serial device.

charge the battery pack that is in the

terminal.

242XOP.002

Before installing and using the optical link

adapter, please read these instructions

thoroughly and retain them for future reference.

6001 36th Avenue West

P.O. Box 4280

Everett, WA 98203-9280

Part No. 065826-004

Installing the Optical Link

Adapter

I/O

F2F4

FnL

ABCDE

HIJ

KLMNO

PQRST

VWXY

FnREnter

789

456

TabEsc

TRAKKER

ANTARES

2420

Guide post

(2 places)

Latch

(2 places)

242XOP.001

1. Press

to turn off the terminal.

2. Insert the adapter guide posts into the

locating holes on the underside of the

terminal.

3. Gently rotate the adapter upward to insert

the adapter latches into the slot on the back

of the terminal. Push forward on the locking

buttons until the buttons “snap” into place.

Now you are ready to connect a communi-

cations cable and attach the power supply to the

adapter. You can operate the terminal and

adapter without the power supply, but the

battery pack must be fully charged.

Removing the Optical Link Adapter

1. Press on the locking buttons to release the

adapter latches and unlock the adapter.

2. Gently rotate the adapter downward to

remove the adapter from the terminal.

Connecting the Communications

Cable to the Optical Link Adapter

The optical link adapter uses a 9-pin serial port for

RS-232 communications. Use one of the following

Intermec cables to communicate between the terminal

and a device:

9-pin connector to 9-pin connector, 5-wire, null

modem cable (Part No. 059167)

9-pin connector to 25-pin connector, 3-wire, null

modem cable (Part No. 047569)

242XOP.003

9-pin connector

for RS-232 cable

10-volt power

supply jack

The adapter serial port pin assignments are:

RXD (Receive data)

TXD (Transmit data)

DTR (Data terminal ready)

GND (Signal ground)

RTS (Request to send)

CTS (Clear to send)

242XOP.006

To connect the serial cable

1. Connect the serial cable to the 9-pin connector

located on the front of the adapter.

2. Plug the other end of the serial cable into the device

serial port.

Connecting the Power Supply

to the Optical Link Adapter

The optical link adapter has a 10V power

supply jack for running the terminal and the

adapter using an AC power source. The power

supply will also charge the lithium-ion battery

pack that is in the terminal.

The power supply (Part No. 065236) is ordered

separately.

242XOP.005

To the host

computer

or device

Optical link

adapter

To the

power

supply

FnL

ABCDE

HIJ

KLMNO

PQRST

VWXY

FnR Enter

TabEsc

To connect the power supply

1. Attach the power supply connector to the

power supply jack located on the front of the

adapter.

2. Plug the power supply power cord into a

powered AC wall outlet.

1 2 3

Andere Handbücher für Trakker Antares 2400

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intermec Adapter Handbücher

Intermec

Intermec CK60 Ethernet Multidock Bedienungsanleitung

Intermec

Intermec 751G Bedienungsanleitung

Intermec

Intermec 1700 Series Bedienungsanleitung

Intermec

Intermec AN3 Bedienungsanleitung

Intermec

Intermec CN3 Series Bedienungsanleitung

Intermec

Intermec CN70 RFID Bedienungsanleitung

Intermec

Intermec CN2A Bedienungsanleitung

Intermec

Intermec CN3 Series Bedienungsanleitung

Intermec

Intermec SF51 Bedienungsanleitung

Intermec

Intermec CN3 Series Bedienungsanleitung

Intermec

Intermec CK60 Ethernet Multidock Bedienungsanleitung

Intermec

Intermec Ethernet Adapter Bedienungsanleitung

Intermec

Intermec CK60 Ethernet Multidock Bedienungsanleitung

Intermec

Intermec BSM-RN41 Bedienungsanleitung

Intermec

Intermec USB Bluetooth Adapter Bedienungsanleitung

Intermec

Intermec EasyLAN 10I2 Bedienungsanleitung

Intermec

Intermec EasyLAN 10I2 Bedienungsanleitung

Intermec

Intermec CK70 RFID Bedienungsanleitung

Intermec

Intermec AA23 Bedienungsanleitung

Intermec

Intermec 1100 Series Bedienungsanleitung

Intermec

Intermec L5020 Bedienungsanleitung

Intermec

Intermec BU-2073-J Bedienungsanleitung

Intermec

Intermec CN50 Bedienungsanleitung

Intermec

Intermec CN2 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung