Intermec IV7 Bedienungsanleitung

IV7

Vehicle-Mount Reader Data Cable Kit Instructions

Use this cable to connect the IV7 Vehicle-Mount Reader to:

• the serial port on a PC.

• general purpose input/output (GPIO) devices such as motion sensors.

These instructions explain how to assemble the data cable and include

guidelines for installing the cable on the vehicle.

This kit (P/N 203-776-001) includes these items:

• Data cable with 20-pin connector, 12 ft (P/N 236-086-001)

• Heatshrink tubing, 1/8 in x 3 ft

• Twenty-four crimp connectors (P/N 809-083-027)

• Four 2K, 1-watt resistors

Required Tools

To assemble the data cable, you need these tools:

• Wire cutters and stripper

• Crimping tool

•Heatgun

Note: Before you assemble the data cable, you need to choose a

mounting location for the IV7 on the vehicle. For more

information, see the IV7 Vehicle-Mount Reader Instructions (P/N

075280-xxx for the standard IV7, or P/N 943-100-xxx for the

ALBR IV7).

Assembling the Data Cable

Once you have determined where the IV7 will be mounted on the vehicle,

you can begin assembling the data cable.

To assemble the data cable

1Strip the sheath from the unterminated end of the cable as needed. If

necessary, be sure to leave enough room for strain relief.

2Install connectors as needed on the cable. Use heatshrink tubing to

protect the connections. For wiring information, see the “Data Cable

Wiring Information” table on the next page.

3(Optional) If you are connecting an input device to the IV7 GPIO

interfaces, install a 2K, 1-watt resistor in series with the input wiring as

shown in the next illustration. The resistor provides protection against

over current and over voltage situations.

GPIO Interface Wiring: Install a 2K, 1-watt resistor in the GPIO input line.

For more information on using the IV7 GPIO interfaces, see the IV7

instructions.

Note: Depending on your installation, you may need to use

different terminal lugs (not supplied).

To IV7

GPIO RTN

To IV7

GPIO input

Typical sensor interface

+12V source

To IV7

GPIO output

50 mA max.

+5V

Installing the Data Cable

After you assemble the data cable, install it on the vehicle as described in the

IV7 instructions.

For more information on safely installing the cable, see the next section.

Data Cable Wiring Information

Pin Color Description

1 Black TXD from IV7

2White RXD to IV7

3Red Ground

4Green CTS from IV7

5 Orange RTS to IV7

6Blue NC

7 White/Black GP Input 0

8Red/Black GP Input 1

9 Green/Black GP Input 2

10 Orange/Black GP Input 3

11 Blue/Black GPIO Return 1

12 Black/White GPIO Return 2

13 Red/White GPIO Return 3

14 Green/White GPIO Return 4

15 Blue/White GPIO Return 5

16 Black/Red NC

17 White/Red GP Output 0

18 Orange/Red GP Output 1

19 Blue/Red GP Output 2

20 Red/Green GP Output 3

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

2007 Intermec Technologies

Cable Safety Guidelines

In addition to the data cable, the IV7 requires power and antenna cables to

connect it to your vehicle-mounted RFID system. As you install the cables,

follow these safety guidelines:

• Make sure that the cable routing does not interfere with other equipment

or vehicle controls.

• Keep cables as short as practical and route all cables to minimize exposure

to damage.

• Make sure the cables will not be pinched or rubbed by moving parts on

the vehicle. You may need to sheath the cable to prevent it from being

pinched.

• Secure the cables every 15 cm (6 in) throughout the length of the cable

run using hardware appropriate for the installation.

• Use a snap-in bushing if the cables pass through a firewall or other sheet

metal.

Note: Most vehicle manufacturers offer pulley kits for installation

of wiring with risers. Intermec recommends using these

manufacturer-specific kits with any installation of the IV7 on a

forklift load back rest assembly.

IV7 Vehicle-Mount Reader Data Cable Kit Instructions

*943-067-002*

P/N 943-067-002

Andere Handbücher für IV7

Andere Intermec Barcode-Lesegerät Handbücher

Intermec

Intermec SR61T2D Bedienungsanleitung

Intermec

Intermec SR61T1D Bedienungsanleitung

Intermec

Intermec EasyCoder F4 Leitfaden

Intermec

Intermec MaxiScan 3100 Bedienungsanleitung

Intermec

Intermec IP3 Intellitag Bedienungsanleitung

Intermec

Intermec EasyCoder PX4i Bedienungsanleitung

Intermec

Intermec EasyCoder PF2i Bedienungsanleitung

Intermec

Intermec EasyCoder PD41 Bedienungsanleitung

Intermec

Intermec IP4 Handbuch

Intermec

Intermec SF51 Bedienungsanleitung

Intermec

Intermec Sabre 1555 Bedienungsanleitung

Intermec

Intermec SR61T Bedienungsanleitung

Intermec

Intermec SF51 Bedienungsanleitung

Intermec

Intermec SG10T Bedienungsanleitung

Intermec

Intermec ScanImage 1470B Bedienungsanleitung

Intermec

Intermec SG20T1D Bedienungsanleitung

Intermec

Intermec 3400 Bedienungsanleitung

Intermec

Intermec SR60 Bedienungsanleitung

Intermec

Intermec EasyCoder 601XP Bedienungsanleitung

Intermec

Intermec SF61BUG Bedienungsanleitung

Intermec

Intermec SG20B Bedienungsanleitung

Intermec

Intermec MaxiScan 1000 Kurzanleitung zur Einrichtung

Intermec

Intermec ScanPlus 1800 Bedienungsanleitung

Intermec

Intermec IF61 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung