Intersil ISL85003EVAL2Z Bedienungsanleitung

ISL85003EVAL2Z, ISL85003AEVAL2Z

Evaluation Board User Guide

AN1930 Rev.1.00 Page 1 of 5

Aug 28, 2014

AN1930

Rev.1.00

Aug 28, 2014

USER’S MANUAL

Description

The ISL85003 and ISL85003A kits are intended for use for

point-of-load applications sourcing from 4.5V to 18V. The kits

are used to demonstrate the performance of the ISL85003

and ISL85003A, low quiescent current high efficiency

synchronous buck regulators.

The ISL85003 and ISL85003A are offered in a 4x3mm dual flat

no lead (DFN) package.

Specifications

The boards are designed to operate at the following operating

conditions:

• Input voltage range from 4.5V to 18V

• Resistor programmable output voltage from 0.8V, ±1%

• Up to 3A output current

• Current mode control

- DCM/CCM

- Internal or external compensation options

- 500kHz switching frequency option

- External synchronization up to 2MHz on ISL85003

• Adjustable soft-start time on the ISL85003A

• Operating junction temperature range: -40°C to +125°C

Quick Setup Guide

1. Ensure that the circuit is correctly connected to the supply

and loads prior to applying any power.

2. Connect the bias supply to VIN, the plus terminal to VIN (P4)

and the negative return to PGND (P5).

3. Connect the output load to V0, the plus terminal to V0 (P8)

and the negative return to PGND (P9).

4. Verify that the position is PWM or PFM for SW2.

5. Verify that the position is ON for SW1.

6. Turn on the power supply.

7. Verify the output voltage is 5V for VO.

Recommended Equipment

The following materials are recommended to perform testing:

• 0V to 25V power supply with at least 10A source current

capability

• Electronic loads capable of sinking current up to 7A

• Digital multimeters (DMMs)

• 100MHz quad-trace oscilloscope

• Signal generator

Key Board Features

•Small,compactdesign

• Switch selectable EN (enabled/disabled)

• Switch selectable MODE (auto-DCM/forced-PWM)

• Connectors and test points for easy probing

References

•ISL85003, ISL85003A datasheet

Evaluating the Other Output

Voltage

The ISL85003 and ISL85003A kit outputs are preset to 5V for

VOUT; however, the output voltages are programmed using an

external resistor divider that scales the feedback relative to the

internal reference voltage. The output voltage programming

resistor, R2, will depend on the value chosen for the feedback

resistor, R1, and the desired regulator output voltage, VOUT.

The value for the feedback resistor R1is typically between

10kΩand 400kΩas shown in Equation 1.

If the output voltage desired is 0.8V, then R2is left

unpopulated. R1is still required to set the low frequency pole

of the modulator compensation.

Switch Control

The ISL85003 and ISL85003A evaluation boards contain SW1

and SW2 for various controls of the ISL85003 and ISL85003A

circuitries. Table 1 details this function.

Ordering Information

PART NUMBER DESCRIPTION

ISL85003EVAL2Z Evaluation Board for ISL85003FRZ and

ISL85003AFRZ

TABLE 1. SWITCH SETTINGS

SW1 ENABLE FUNCTION

1OFFDisableV0

3ONEnableV0

SW2 MODE FUNCTION

1DCMForceDCM

3 PWM Fixed PWM frequency at light load

R10.8V

VOUT 0.8V–

-------------------------------

=(EQ. 1)

ISL85003EVAL2Z, ISL85003AEVAL2Z

AN1930 Rev.1.00 Page 2 of 5

Aug 28, 2014

Components Selection

VOUT 0.8V 1V 1.2V 1.5V 1.8V 2.5V 3.3V 5V

C1, C210µF 10µF 10µF 10µF 10µF 10µF 10µF 10µF

C522µF 22µF 22µF 47µF 47µF 47µF 47µF 47µF

C622µF 22µF 22µF 22µF 22µF 22µF 22µF 22µF

C4Open Open Open 4.7pF 4.7pF 4.7pF 4.7pF 4.7pF

L11.8µH 2.2µH 2.2µH 3.3µH 3.3µH 3.3µH 4.7µH 4.7µH

R1301kΩ301kΩ301kΩ301kΩ301kΩ301kΩ301kΩ301kΩ

R2Open 1.2MΩ604kΩ344kΩ241kΩ142kΩ96.3kΩ57.6kΩ

NOTE: VIN = 12V, IOUT = 3A; The components selection table is a suggestion for typical application using internal compensation mode. For applications

that require high output capacitance greater than 200µF, R1should be adjusted to maintain a loop response bandwidth about 40kHz.

ISL85003EVAL2Z Evaluation Board

FIGURE 1. TOP VIEW FIGURE 2. BOTTOM VIEW

AN1930 Rev.1.00 Page 3 of 5

Aug 28, 2014

ISL85003EVAL2Z, ISL85003AEVAL2Z

ISL85003EVAL2Z Rev B Schematic

VCC

VOUT

SYNC

OFF

VIN

SYNC

DCM

PWM ON

VCCVCC

VOUT

DNP

10uF

0.1uF

SW2

4.7p

SW1

DNP

ENABLE

47uF

C10

150uF

2N7002

200k

57.1k

DNP

VCC

22uF

SYNC

10uF

R11

DNP

200k

DNP P8

VOUT

4.7uH

LTST-C190KGKT

VIN

R14

200k

301k

1uF

GND

DNP

ISL85003

COMP

AGND

6PHASE 7

PHASE 8

VIN 9

VIN 10

VDD 11

BOOT 12

EPAD

SYNC

PHASE

GND

VOUT

Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is

cautioned to verify that the document is current before proceeding.

For information regarding Intersil Corporation and its products, see www.intersil.com

AN1930 Rev.1.00 Page 4 of 5

Aug 28, 2014

ISL85003EVAL2Z, ISL85003AEVAL2Z

Bill of Materials

PART NUMBER QTY UNITS

REFERENCE

DESIGNATOR DESCRIPTION MFR MFR PART #

ISL85003FRZ 1 ea U1 IC-3A BUCK REGULATOR, 12P, DFN, 4X3,

ROHS

INTERSIL ISL85003FRZ

ISL85003AFRZ 1 ea U1 IC-3A BUCK REGULATOR PWM, 12P, DFN, 4X3,

ROHS

INTERSIL ISL85003AFRZ

EEE-FK1H151P-T 1 ea C10 CAP, SMD, 10.3mm, 150µF, 50V, 20%, ROHS,

ALUM.ELEC.

PANASONIC EEE-FK1H151P

H1044-004R7-50VR25-T 1 ea C4 CAP, SMD, 0402, 4.7pF, 50V, 0.25pF, NPO,

ROHS

MURATA GRM36COG4R7C050AQ

H1044-DNP 0 ea C7, C8, CSS CAP, SMD, 0402, DNP-PLACE HOLDER, ROHS

H1045-00104-50V10-T 1 ea C3 CAP, SMD, 0603, 0.1µF, 50V, 10%, X7R, ROHS AVX 06035C104KAT2A

H1045-00105-16V10-T 1 ea C9 CAP, SMD, 0603, 1µF, 16V, 10%, X5R, ROHS MURATA GRM188R61C105KA12D

H1065-00106-25V10-T 2 ea C1, C2 CAP, SMD, 1206, 10µF, 25V, 10%, X7R, ROHS VENKEL C1206X7R250-106KNE

H1065-00226-25V10-T 2 ea C5, C6 CAP, SMD, 1206, 22µF, 25V, 10%, X5R, ROHS MURATA GRM31CR61E226KE15L

RLF7030T-4R7M3R4 1 ea L1 COIL-PWR INDUCTOR, SMD, 7.3X6.8mm,

4.7µH, 20%, 3.5A, ROHS

TDK RLF7030T-4R7M3R4

131-4353-00 2 ea J1, J2 CONN-SCOPE PROBE TEST PT, COMPACT, PCB

MNT, ROHS

TEKTRONIX 131-4353-00

1514-2 4 ea P4, P5, P8, P9 CONN-TURRET, TERMINAL POST, TH, ROHS KEYSTONE 1514-2

5002 4 ea P1, P2, P6, P7 CONN-MINI TEST POINT, VERTICAL, WHITE,

ROHS

KEYSTONE 5002

BAT54C-T 1 ea D2 DIODE-RECTIFIER, SMD, SOT23, 3P, 30V,

200mA, ROHS

FAIRCHILD BAT54C

LTST-C190KGKT-T 1 ea D1 LED, SMD, 0603, GREEN CLEAR, 2V, 20mA,

571nm, 35mcd, ROHS

LITEON/VISHAY LTST-C190KGKT

2N7002LT1G-T 1 ea Q1 TRANSISTOR-MOS, N-CHANNEL, SMD, SOT23,

60V, 115mA, ROHS

SEMICONDUCTOR

2N7002LT1G

H2510-00R00-1/16W-T 1 ea R11 RES, SMD, 0402, 0Ω, 1/16W, 5%, TF, ROHS VENKEL CR0402-16W-00T

H2510-03013-1/16W1-T 1 ea R1 RES, SMD, 0402, 301k, 1/16W, 1%, TF, ROHS YAGEO RC0402FR-07301KL

H2510-05762-1/16W1-T 1 ea R2 RES, SMD, 0402, 57.6k, 1/16W, 1%, TF, ROHS PANASONIC ERJ-2RKF5762X

H2510-DNP 0 ea R3 RES, SMD, 0402, DNP, DNP, DNP, TF, ROHS

H2511-00200-1/10W1-T 1 ea R4 RES, SMD, 0603, 20Ω, 1/10W, 1%, TF, ROHS PANASONIC ERJ-3EKF20R0V

H2511-02001-1/10W1-T 1 ea R5 RES, SMD, 0603, 2k, 1/10W, 1%, TF, ROHS KOA RK73H1JTTD2001F

H2511-02003-1/10W1-T 3 ea R6, R7, R14 RES, SMD, 0603, 200k, 1/10W, 1%, TF, ROHS VENKEL CR0603-10W-2003FT

H2511-DNP 0 ea R8, R9 RES, SMD, 0603, DNP-PLACE HOLDER, ROHS

GT11MSCBE-T 2 ea SW1, SW2 SWITCH-TOGGLE, SMD, 6PIN, SPDT, 2POS, ON-

ON, ROHS

ITT INDUSTRIES/

C&K DIVISION

GT11MSCBE

SJ-5003-BLACK 4 ea Bottom four

corners

BUMPONS, 0.44inW x 0.20inH, DOMETOP,

BLACK

3M SJ-5003SPBL

All trademarks and registered trademarks are the property of their respective owners.

ISL85003EVAL2Z, ISL85003AEVAL2Z

AN1930 Rev.1.00 Page 5 of 5

Aug 28, 2014

PCB Layout

FIGURE 3. TOP LAYER FIGURE 4. INNER LAYER 1

FIGURE 5. INNER LAYER 2 FIGURE 6. BOTTOM LAYER

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Intersil:

ISL85003AEVAL2Z

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intersil Hauptplatine Handbücher

Intersil

Intersil ISL70321SEHDEMO1Z Bedienungsanleitung

Intersil

Intersil ISL73033SLHEV1Z Bedienungsanleitung

Intersil

Intersil ISL54059EVAL1Z Bedienungsanleitung

Intersil

Intersil ZL6100EVAL2Z Montage- und Bedienungsanleitung

Intersil

Intersil ISL73847SEHEV2Z Bedienungsanleitung

Intersil

Intersil ISL9214AEVAL1Z Gebrauchsanweisung

Intersil

Intersil ISLVERSALDEMO2Z Bedienungsanleitung

Intersil

Intersil HI5905EVAL2 Bedienungsanleitung

Intersil

Intersil ISL8201M Bedienungsanleitung

Intersil

Intersil ISL5761EVAL1 Bedienungsanleitung

Intersil

Intersil ISL70001ASEHEV1Z Montage- und Bedienungsanleitung

Intersil

Intersil ISL70321SEHEV Z Series Bedienungsanleitung

Intersil

Intersil ISL6227EVAL1 Handbuch

Intersil

Intersil JESD204B Bedienungsanleitung

Intersil

Intersil ISL78268EVAL1Z Bedienungsanleitung

Intersil

Intersil ISL72813SEHEV1Z Bedienungsanleitung

Intersil

Intersil ISL76534EVAL1Z Bedienungsanleitung

Intersil

Intersil ISL8200MEVAL1PHZ Bedienungsanleitung

Intersil

Intersil ISL76683 Bedienungsanleitung

Intersil

Intersil ISL85014EVAL1Z Bedienungsanleitung

Intersil

Intersil ISL55141 Bedienungsanleitung

Intersil

Intersil ISL97671A Bedienungsanleitung

Intersil

Intersil ISL8014AEVAL2Z Montage- und Bedienungsanleitung

Intersil

Intersil ISL59442EVAL1 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung