Intex Krystal Clean Poolwater 8221 Bedienungsanleitung

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 1

INTEX®OWNER’S MANUAL

Krystal Clean Poolwater™ System

Model 8221 220 - 230 V~, 50 Hz

Model 8231 230 - 240 V~, 50 Hz

450W, IPX4, Hmax 1.5 m, Hmin 0.19 m

Max. Water Temperature 35

Warning 2

Parts Reference 3-4

Product Information and Specifications 5

Set Up Instructions 6-8

Salt & Pool Water Volumes 9

Intex Pools Salt Table 10

Intex Pools Operating Time Table 11

Non Intex Pools Salt Table 12

Non Intex Pools Operating Time Table 12

Operating Instructions 13-15

Alarm Codes & LED Code Chart 16-17

Stationary Mounting Option 17

Maintenance 18-20

Long Term Storage 20

INTEX 3-Way Test Strips 21

Pool Maintenance and Chemical Definitions 21

Trouble Shooting Guide 22-24

General Aquatic Safety 24

Limited Warranty 25

Intex Service Center Locations 25

TABLE OF CONTENTS

IMPORTANT SAFETY RULE

READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING

AND USING THIS PRODUCT.

Made in China

Intex Trading Ltd.

C/O Intex (HongKong) Ltd.

Intex Trading B.V.

P. O. Box nr. 1075-4700 BB Roosendaal

104**-R0-0709

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 2

This Saltwater System/Filter Pump is intended to be used only for the purposes described in this

manual. Failure to follow all product, package and package insert safety and installation instructions

could result in property damage, electric shock, entanglement or other serious injury or death.

READ AND FOLLOW ALL INSTRUCTIONS

•To reduce the risk of injury, do not permit children to use this product. Always supervise children

and those with disabilities.

•Risk of electric shock. Connect this product only to a grounding type receptacle protected by a

ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a qualified

electrician if you cannot verify that the receptacle is protected by a GFCI/RCD. Use a qualified

electrician to install the GFCI/RCD, which has a maximum rate of 30mA. Do not use a portable

residual current device (PRCD).

•Do not bury electrical cord. Locate cord where it will not be damaged by lawn mowers, hedge

trimmers, and other equipment.

•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard.

•To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter

plugs to connect unit to electric supply; provide a properly located outlet.

•Assembly and disassembly by adults only.

•Do not attempt to plug in or unplug this product while standing in water or when your hands are

wet.

•Children must stay away from this product and all electrical cords.

•Do not operate this product when pool is occupied.

•Always unplug this product from the electrical outlet before cleaning and servicing.

•This product is for use with storable pools only. Do not use with permanently-installed pools. A

storable pool is constructed so that it is capable of being readily disassembled for storage and

reassembled to its original integrity.

•Keep this product more than 2m away from the pool.

•Keep this product more than 3.5m away from the pool (for France only).

•Keep the plug of this product more than 3.5m away from the pool.

•The plug shall be accessible after product installed.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC

SHOCK, ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.

WARNING

Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.

IMPORTANT SAFETY RULE

The product warnings, instructions and safety rules provided with this product represent some of the

common risks associated with water recreation appliances and do not cover all instances of risk or

danger. Please use common sense and good judgement when enjoying any water activity.

For Portable, Above-The-Ground Pools Only

REF. NO. DESCRIPTION QTY. REMARK

05CG-01 Electrolytic Cell (with Titanium Plates) 1

05CG-02 O-Ring A (pre-installed in 05CG-01) 1

05CG-03 Screw 2

05CG-04 Flow Sensor 1

05CG-05 O-Ring B (pre-installed in 05CG-06) 1

05CG-06 Flow Sensor Conduit 1

05CG-07 O-Ring C (pre-installed in 05CG-06) 1

05CG-08 Debris Screen 1

05CG-14 Angle Joint 1

05CG-15 O-Ring D (pre-installed in 05CG-14) 1

5F12 Air Release Valve/Sediment Release Valve 2

5F13 Valve O-Ring 2

6F14 Filter Housing Cover 1

6F15 Filter Housing O-Ring 1

6F16 Threaded Filter Housing Collar 1

5NF32 Pump Hose with nuts 2

59905 Filter Cartridge 1

05F-37 Air Release Valve B (with o-ring) 1

05F-38 Water Transfer Hose (with collar and 2 hose clamps) 1

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 3

Before assembling your product, please take a few minutes to check the contents and become familiar

with all the parts.

PARTS REFERENCE

5F12

05F-37

05CG-03

05F-38

5NF32 05CG-02 05CG-01 05CG-05 05CG-06 05CG-08 05CG-14

CELL HOUSING

RECEPTACLE

ELECTROLYTIC CELL

LINE CORD

POWER CORD

5F13

6F16

5F13

05CG-04 05CG-15

05CG-07

5F12

FLOW SENSOR

LINE CORD

6F14

6F15

5NF32

WATER FROM

POOL

WATER TO

POOL

59905

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 4

REF. NO. DESCRIPTION QTY. REMARK

5F01 Strainer Grid

06NF-02 Threaded Strainer Connector

5F03 Flat Strainer Rubber Washer

5F04 Strainer Nut

06NF-05 Step Washer

5F11 Hose O-Ring

06NF-30 Plunger Valve (06NF-05 & 5F11 included) 2

5F31 Large Strainer (5F01/03/04 & 06NF-02) 2 For 18’ and above Pools

05CG-12 Adaptor B 2 For 16’ and below Pools

F12 Strainer 2 For 16’ and below Pools

5F11

LINER

06NF-30

06NF-05

5F04

05CG-12

5F03 06NF-02 5F01

PARTS REFERENCE (CONT.)

F12

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 5

Product Information and Specifications

How the Chlorine is Generated

Common salt (sodium chloride) is made up of two elements, sodium and chloride. During the installation of

your Saltwater System/Filter Pump, a measured quantity of salt is dissolved in the pool water to make it

slightly salty. This pool water is passed through the Saltwater System’s electrolytic cell to produce chlorine

which is dissolved instantly in the water. The chlorine instantly starts to destroy bacteria, viruses, algae and

oxidizes other organic materials.

Key Saltwater System Parts:

•Power Supply

The power supply converts AC electrical current to a low voltage DC current. This is required by the

cell to perform the electrolysis that creates chlorine.

•Electrolytic Cell (with Titanium Plates)

The electrolytic cell contains bipolar titanium electrodes which perform the electrolysis and produce liquid

chlorine when energized with DC electricity. Chlorine is generated when pool water containing salt

passes through the cell. The chlorine production can be varied by changing the number of hours the

Saltwater System is operating each day. The Saltwater System has a built-in self cleaning cycle that

operates every two hours without interrupting chlorine production.

•Flow Sensor

The flow sensor protects the electrolytic cell and ensures there is adequate water flowing through the

cell. When the water flow drops below minimum flow rate, the electrolytic cell will automatically shut

down to protect the titanium plates. A safety buzzer will sound and the LED display panel will show a

signal code (see “LED Code Chart”) indicating the problem.

•Electronic Control Station

The electronic control station contains an LED display panel and a set of pushbuttons to program the

Saltwater System operating hours. It also monitors the different parameters such as salt level, water

flow and the electrolytic cell activity. If any deviation from the norm occurs then a buzzer will sound and

the LED display panel will show a signal code (see “LED Code Chart”) indicating the problem.

PRODUCT SPECIFICATIONS

Wattage: 450 W

Ideal Salt Level: 3000 ppm (parts per million)

Maximum Chlorine Output/hour: 24 grams/hour

Limited Warranty: 1 Year (see “Limited Warranty”)

Water Outlet

Water Inlet

Flow Sensor

Electronic

Control Station

Electrolytic Cell

(with Titanium

Plates)

IMPORTANT: The Saltwater System/Filter Pump must be installed as the last piece of pool

equipment in the water return line to the pool. This location extends the life of the titanium plates.

Strainer & Plunger Valve Set Up (16’ and below AGP)

The Saltwater System/Filter Pump assembly includes two (2) strainer-control mechanisms that are to

be installed in the pool liner's two (2) protruding hose connections with adaptor B. The strainer grid

prevents large objects from jamming and/or damaging the filter pump and the plunger valve assembly

prevents water from flowing into the filter pump while the filter cartridge is being placed or cleaned.

Install the strainer and plunger valve before inflating the pool liner top ring.

1. Grasp the strainer and plunger valve mechanism.

2. In a counter-clockwise motion unscrew plunger valve union from the threaded strainer connector

(06NF-02). Be careful not to lose the step rubber washer (06NF-05).

3. Grasp the plunger valve assembly. Make sure the step washer (06NF-05) is in place. Connect

adaptor B (05CG-12) to plunger valve union.

4. Repeat steps 1 through 3 for another plunger valve.

5. Remove wall plug and then insert the strainer (F12) into each of the protruding hose connection.

Adaptor B (05CG-12) fit over the strainer inserted into the connection.

6. Examine the plunger valve to see if the handle is pushed fully down to the "0/1" position. If not,

then grasp the handle at the top and push down turning the handle in a clockwise direction until the

plastic protruding notch anchors in the "0/1" position. This will prevent water from flowing out during

filling.

7. Repeat steps 1 through 6 for the 2nd protruding hose connection.

8. The pool liner is now ready to fill with water. Consult the above-ground-pool owner's manual for

filling instructions.

---- INTERVAL FOR POOL FILLING ----

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 6

Set Up Instructions

LINER

5F11

F12

06NF-30

06NF-05 05CG-12

Strainer & Plunger Valve Set Up (18’ and above AGP)

The Saltwater System/Filter Pump assembly includes two (2) strainer-control mechanisms that are to

be installed in the pool liner's two (2) pre-cut holes. The strainer grid prevents large objects from

jamming and/or damaging the filter pump and the plunger valve assembly prevents water from flowing

into the filter pump while the filter cartridge is being placed or cleaned. Install the strainer and plunger

valve before inflating the pool liner top ring.

1. Grasp the strainer and plunger valve mechanism.

2. In a counter-clockwise motion unscrew plunger valve union from the threaded strainer connector

(06NF-02). Be careful not to lose the step rubber washer (06NF-05). Place the plunger valve on the

ground in a safe place.

3. In a counter-clockwise motion unscrew the strainer nut (5F04) from the threaded connector

(06NF-02). Leave the flat washer (5F03) on the connector (06NF-02).

4. From the inside of the pool liner insert the connector (06NF-02) into one of the pre-cut holes with

the washer remaining on the connector to be placed against the inside of the liner wall.

5. With the flat side of the strainer nut (5F04) facing the outside wall of the liner in a clockwise motion

screw the strainer nut (5F04) back onto the threaded connector (06NF-02). Before assembly,

lubricate the threads with a petroleum jelly.

6. Finger tighten the strainer grid (5F01) and the strainer nut (5F04) onto the threaded connector

(06NF-02).

7. Grasp the plunger valve assembly. Make sure the step washer (06NF-05) is in place.

8. In a clockwise motion screw the plunger valve union back onto the threaded connector (06NF-02).

9. Examine the plunger valve to see if the handle is pushed fully down to the "0/1" position. If not,

then grasp the handle at the top and push down turning the handle in a clockwise direction until the

plastic protruding notch anchors in the "0/1" position. This will prevent water from flowing out during

filling.

10. Repeat steps 1 through 9 for the 2nd liner pre-cut hole.

11. The pool liner is now ready to fill with water. Consult the above-ground-pool owner's manual for

filling instructions.

---- INTERVAL FOR POOL FILLING ----

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 7

Set Up Instructions (cont.)

LINER

5F11

06NF-30

06NF-05 5F04 5F03 06NF-02 5F01

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

Set Up Instructions (cont.)

Saltwater System/Filter Pump

1. Remove the Saltwater System/Filter Pump and hoses from the packaging.

2. Place the Saltwater System/Filter Pump in a location for hose (5NF19) connections to the plunger

valve assemblies.

Note: Some regional regulations may require the filter pump to be mounted on a stationary

platform.There are two (2) mounting holes located in the pump base for this reason.

Consult your local authorities for filter pump mounting requirements.

3. Grasp the two (2) pump hoses (5NF19) and connect the hose nuts to the Saltwater Pool

System/Filter Pump.

4. In a counter-clockwise motion unscrew the threaded filter housing collar (6F16) from the filter

housing. Place it in a safe place.

5. The Saltwater System/Filter Pump is an airtight system. In a counter-clockwise motion turn both air

release valves (5F12 & 05F-37) 1 - 2 turns to open. DO NOT remove air release valves as water

will expel with force if the motor is turned on and injury may occur.

6. Grasp and remove the filter housing cover (6F14). Check to see if a cartridge is inside the housing.

If yes, replace the cover, finger tighten the housing collar (6F16) back onto the filter housing.

7. Gently finger tighten the sediment release valve located at the bottom of the housing to be sure

that water does not leak out.

8. When the pool is filled connect the hose from the electrolytic cell outlet to the highest strainer

assembly. The hose connection is made at the bottom of the plunger valve assembly. Use the hose

nut to attach the hose.

9. Connect the 2nd hose to the middle of the motor housing and to the remaining liner connection.

SAVE THESE INSTRUCTIONS

Page 8

To prevent air lock, open the lower plunger valve (connected inlet hose) first and then the upper

plunger valve (connected outlet hose). Open air release valves, wait until water starts to flow out of the

air release valves, close air release valves.

IMPORTANT

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

Salt & Pool Water Volumes

Use only Sodium Chloride Salts

Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also acceptable to use water

conditioning salt pellets (the compressed forms of evaporated salt), but it will take longer time for them

to dissolve. Do not use iodized or yellow (yellow prussiate of soda) colored salt. Salt is added to

the pool water and the electrolytic cell uses this salt to create chlorine, the purer the salt the better the

performance of the electrolytic cell.

Optimum Salt Levels

The ideal salt level in the pool water is between 2500-3500 ppm (parts per million) with 3000 ppm

being optimal.

A too low salt level will reduce the efficiency of the Saltwater System and result in low chlorine

production. A high salt level may begin to generate a salty taste to your pool water (this may occur at a

salt level above 3500-4000ppm). Too high of a salt level may damage the power supply and cause

corrosion to pool metal fixtures and accessories. The following “salt table” shows the quantity of salt to

use. The salt in the pool is constantly recycled. Salt loss is due only to pool water physically removed

from the pool. Salt is not lost due to evaporation.

How to Add or Remove Salt

Adding Salt

1. Depress the ON button on the filter pump switch to circulate pool water.

2. Keep the Saltwater System “OFF”.

3. Determine the amount of salt to be added (see “Salt Table”).

4. Evenly spread the proper amount of salt around the inside perimeter of the pool.

5. To avoid clogging the filter, do not add salt through the skimmer.

6. Brush the pool bottom to speed up the dissolving process. Do not allow salt to pile up on the

bottom of the pool. Run the filter pump 24 consecutive hours to thoroughly dissolve the salt.

7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System and set the saltwater

pool system to desired operating time (see “Operating Time Table”).

Removing Salt

If too much salt has been added, the unit will beep and display “code 92” (see “Alarm Codes”). You

need to lower the salt concentration. The only way to lower the salt concentration is to partially drain the

pool and refill with fresh water. Drain and refill approximately 20% of the pool’s water until the “Code 92”

disappears.

Pool Volume Calculation

Rectangular Length x Width x Average Depth x 7.5 Length x Width x Average Depth

Circular Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79

Oval Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80

Types of Pool Gallons

(pool size in feet)

Cubic Meters

(pool size in meters)

SAVE THESE INSTRUCTIONS

Page 9

104

(104) ENGLISH SALTWATER SYSTEM/FILTER PUMP MODEL8221/8231 SIZE: 7.5” X 10.5” 09/18/2006

SAVE THESE INSTRUCTIONS

Page 10

Intex Pools Salt Table

This table shows how much salt to use to achieve the desired 3000 ppm salt level and how much will

be needed to maintain this level if it drops below this desired level.

Pool Size

Salt Needed for

Startup

Salt Needed when

Low Salt Detected

(CODE “91”)

CIRCULAR

METAL

FRAME POOL

EASY SET POOL

RECTANGULAR

FRAME POOL

OVAL FRAME

POOL

Water Capacity

(

Calculated at 90% for Frame Pool

and 80% for Easy Set & Oval Pool)

(Gals) (Liters) (Lbs) (Kgs) (Lbs) (Kgs)

INTEX ABOVE GROUND POOLS (AGP’s)

3282 12422 80 35 20 10

3861 14614 100 45 25 10

4440 16806 110 50 30 15

4401 16656 110 50 30 15

5061 19154 125 55 35 15

6423 24310 160 75 40 20

6981 26424 175 80 45 20

11483 43462 290 130 75 35

12481 47241 310 140 85 40

2587 9790 65 30 15 10

2822 10680 65 30 20 10

3284 12431 80 35 20 10

3736 14142 95 45 25 10

4032 15262 100 45 25 10

3754 14207 95 45 25 10

4273 16174 110 50 30 15

4614 17462 110 50 30 15

4786 18115 120 55 30 15

5455 20647 135 60 35 15

5894 22309 150 65 40 20

4545 17202 115 50 30 15

7757 29359 195 90 50 25

14364 54368 365 165 95 45

2885 10921 75 35 20 10

4393 16628 110 50 30 15

4738 17935 120 55 30 15

5407 20464 132 60 35 15

5832 22073 145 65 40 20

6925 26212 175 80 45 20

7434 28137 185 85 50 25

9461 35809 235 105 65 30

15' x 36"

15' x 42"

15' x 48"

16' x 42"

16' x 48"

18' x 48"

18' x 52"

24' x 48"

24' x 52"

15' x 33"

15' x 36"

15' x 42"

15' x 48"

15' x 52"

16' x 42"

16' x 48"

16' x 52"

18' x 42"

18' x 48"

18' x 52"

9' x 18' x 52"

12' x 24' x 48"

16' x 32' x 52"

10' x 18' x 42"

12' x 20' x 48"

12' x 20' x 52"

12' x 24' x 48"

12' x 24' x 52"

12' x 28' x 52"

12' x 32' x 48"

12' x 40' x 48"

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Intex Wasserpumpe Handbücher

Intex

Intex Krystal Clear C2500 Bedienungsanleitung

Intex

Intex Krystal Clear C330 Bedienungsanleitung

Intex

Intex Quick-Fil AP634 Bedienungsanleitung

Intex

Intex ECO15230-2 Bedienungsanleitung

Intex

Intex Krystal Clear Deluxe Bedienungsanleitung

Intex

Intex Krystal Clear 603 Bedienungsanleitung

Intex

Intex Krystal Clear SX925 Bedienungsanleitung

Intex

Intex Krystal Clear CS15110 Bedienungsanleitung

Intex

Intex Krystal Clear 601 Bedienungsanleitung

Intex

Intex Krystal Clear C1500 Bedienungsanleitung

Intex

Intex 128644GS Bedienungsanleitung

Intex

Intex Krystal Clear SX925 Bedienungsanleitung

Intex

Intex Quick-Fill 58609 Bedienungsanleitung

Intex

Intex Built-in Fast-Fill AP620A Bedienungsanleitung

Intex

Intex AP638 Bedienungsanleitung

Intex

Intex SF15220 Bedienungsanleitung

Intex

Intex PureSpa SSP-H-10-2 Bedienungsanleitung

Intex

Intex PureSpa PS-BH-10 Bedienungsanleitung

Intex

Intex Krystal Clear 604 Bedienungsanleitung

Intex

Intex QUICK FILL PLUS Bedienungsanleitung

Intex

Intex ECO 7231 Bedienungsanleitung

Intex

Intex Quickfill Plus AP619D Bedienungsanleitung

Intex

Intex Fast-Fill 619PC Bedienungsanleitung

Intex

Intex Quick-Fill AP640 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung