Intimus PB-150 Bedienungsanleitung

PB-150

Comb Binding Machine

95494 1 12/18

CAPABILITIES

Technical Data

Width :

Punching Thickness :

Punch PVC Cover :

Punch PP Cover :

Machine Dimension :

Weight :

Binding Thickness :

ENGLISH

P/01

300mm

15sheets

2sheets

1sheet

44.5x21x28.8cm

500sheets

Numbers of Punch Pins: 21

Pitch : 14.25

Holding fixture for binding elements

Punching&Binding Level

Margin Adjusting Scale

Measuring Scale

Punching Shaft

Paper Guide With Attachment Screw

5kgs

IMPORTANT SAFETY INSTRUCTIONS-KEEP FOR

FUTURE USE

When punching;

- always ensure the machine is on a stable surface

- test punch scrap sheets and set the machine before punching final

documents

- remove staples and other metal articles prior to punching

- never exceed the machines quoted performance

Keep the machine away from heat and water sources.

Never attempt to open or otherwise repair the machine.

SET UP

Please read before use and keep for

future

P/02

Ensure the machine is on a solid surface

2.Check the waste try is empty

and correctly fitted

1.Adjusting paper guide to the

corresponding paper size.

Release attachment screw, adjust paper

guide and fasten attachment screw.

2.Determine the diameter.

Put the block under the measuring scale.

Push slider downwards.

Read the diameter of the binding

element .

3.Adjusting the margin turn right knob

to the corresponding size

PUNCH

4.Insert paper into punching slot,

Press punching lever forward until it stops,

then return to original position

P/03

PUNCH

5.Ensure the paper is less than 15 pieces

BIND

P/04

1.Caution! Lay the plastic binding element

with its spine behind the vertical retaining

fingers and its rings facing down through

the gaps in the fi ngers.

2. Open the binding comb by pushing the binding

lever backward.

Caution! Do not open the comb too wide

as there is danger of over-stretching it which

may weaken the plastic.

3.Take the punched paper with both

hands and insert it directly onto the

open rings of the binding element

BIND

P/05

4. Lay down paper to the front.

Close plastic comb by returning

the binding lever to stop.

REMOVE BOUND BOOK

1.With the binding lever in the rear

position, slide the bound book

over the comb by pushing

the binding lever backwards.

2.Remove the desired pages,

punch and insert the new ones.

Proceed the same way as initially.

REMOVAL OF WASTE CLIPPINGS

The waste tray is located under the machine and is accessed from the front side. For best

results empty the tray regularly.

TROUBLESHOOTING

Problem Cause Solution

Punched holes are not central Edge guide not

set

Adjust edge guide until hole pattern

is correct

Machine will not punch Blockage Check waste tray is empty.

Check for blockage

Punch holes are not parallel

to edge

Debris is stuck below dies

Take stiff cardboard and slide into the

paper entry. Move the cardboard side-

ways to release any stray clippings

into the waste tray

Partial holes Sheets not correctly aligned

to punch pattern

Adjust edge guide and test punch

scrap sheets until correct

Damaged hole edges Possibly overloading the

machine

Punch plastic covers with paper

sheets.Reduce number of sheets being

punched

P/06

95494 1 12/18

intimus International GmbH

Bergheimer Straße 6 - 12

88677 Markdorf / Germany

Tel.: ++49 (0)7544 / 60-0

Fax.: ++49 (0)7544 /

60-248 E-mail:

[email protected]

www.intimus.com

Inhaltsverzeichnis

Andere Intimus Bindemaschine Handbücher

Intimus

Intimus PB-250 Bedienungsanleitung

Beliebte Bindemaschine Handbücher anderer Marken

GBC

GBC CombBind C800pro Bedienungsanleitung

JBI

JBI Alpha-Doc MKIII Bedienungsanleitung

GBC

GBC CombBind A20 Bedienungsanleitung

GBC

GBC DocuBind P100 Bedienungsanleitung

Peach

Peach PB300-20 Bedienungsanleitung

Morgana

Morgana DigiBook 450 Bedienungsanleitung

Rexel

Rexel CB345E Bauanleitung

GBC

GBC AP-2 Bedienungsanleitung

Opus

Opus MB 300 Bedienungsanleitung

Duplo

Duplo DC-645 Bedienungsanleitung

Akiles

Akiles AlphaBind Kurzanleitung

ibico

ibico Thermal Binder 260 Bedienungsanleitung

Rollabind

Rollabind PBS 2000 Bedienungsanleitung

SYSFORM

SYSFORM CP340H Bedienungsanleitung

GBC

GBC THERMALBINDER400T Bedienungsanleitung

GBC

GBC CombBind C20 Bedienungsanleitung

Renz

Renz RENZ DTP 340A Betriebsanleitung

Ricoh

Ricoh RB5020 Bedienungsanleitung