ION Explorer XL Bedienungsanleitung

ExplorerTM XL

User Guide English ( 2 – 8 )

Guía del usuario Español ( 9 – 16 )

Guide d’utilisation Français ( 17 – 24 )

Appendix English ( 25 - 26 )

User Guide (English)

Introduction

Thank you for purchasing the Explorer XL. At ION, your entertainment is as important to us as

it is to you. That’s why we design our products with one thing in mind—to make your life more

fun and more convenient.

Note: Before you first use the product, please fully charge the battery. Your unit was

purposely shipped with a reduced battery charge to ensure safe transit.

Use the included power cable to connect the unit to a power outlet and let it charge for up to

10 hours. This helps ensure the longest life for your battery.

Box Contents

ExplorerTM XL

Power Cable (IEC320 C13, 6 ft. / 183 cm)

Microphone with Cable (8 ft. / 250 cm)

Quickstart Guide

Support

For the latest information about this product (documentation, technical specifications, system

requirements, compatibility information, etc.) and product registration, visit ionaudio.com.

For additional product support, visit ionaudio.com/support.

Rechargeable Batteries

Rechargeable lead-acid batteries are the same type used in automobiles. As with your car

battery, how you use this battery has a significant impact on its lifespan. With proper use and

treatment, a lead-acid battery can last for years. Here are some recommendations for getting

the longest life from the internal battery.

General Usage Fully charge the battery before using it.

Charge the battery completely after each use.

Storage For best product longevity, do not store at exceedingly hot (greater than

90°F/32°C) or exceedingly cold (less than 32°F/0°C) temperatures.

It is acceptable to leave your sound system plugged in. This will not

overcharge the battery.

If you leave the battery level low and do not charge it for 3 months, it may

permanently lose capacity.

Repair If the battery fails to charge, check your fuse near the power cable input. If

your fuse is intact and it still will not charge, contact ION Audio at

ionaudio.com.

Disposal Bring the unit to a recycling center or dispose of in accordance with local

ordinances.

Outdoor Use and Care

Though Explorer XL is water-resistant and able to tolerate splashing water, please review the

tips below to get the best performance from Explorer XL:

•Explorer XL must only be used outdoors with power outlets or extension cords that are

rated for outdoor use.

•Bring Explorer XL indoors during extreme weather.

•Please do not place Explorer XL in standing water.

•Please do not connect the power adapter to Explorer XL in a wet environment. Make sure

the power input, power adapter, and power outlet are all completely dry before making any

connections.

•WARNING: Keep any non-water-resistant devices (phones, music players, etc.) in a dry

place where they will not be affected by water and cause a risk of electric shock.

Quick Setup

1. Make sure all items listed in the Box Contents at the beginning of this guide are included

in the box.

2. Read the Safety & Warranty Manual before using the product.

3. Make sure that you have completely charged the battery prior to first use for maximum

battery life.

4. Power on Explorer XL.

5. Connect your music player with an audio cable or Bluetooth®.

6. Adjust the volume on the music player and on Explorer XL as needed.

7. Turn off Explorer XL when not in use.

Connection Diagram

Items not listed under Introduction >Box Contents are sold separately.

Tablet

Guitar

Smartphone

Microphone

Power

Front Panel Back Panel

Features

Front Panel

A. Display: Shows information relative to the current operation. See Features > Display

Icons for more information.

B. Control Knob: Press to toggle between controlling the volume of the music source

(Bluetooth, Aux, or Radio), mic input, or instrument input/FX, or the Treble and Bass

EQ, as indicated on the display. Turn the knob to increase or decrease the selected

setting.

C. Power Button: Press and hold to turn Explorer XL on or off.

D. Bluetooth Button: Press to pair to a Bluetooth device or disconnect a paired

Bluetooth device and enter Aux mode. Double-press to disconnect a paired Bluetooth

device and search for a different device. See Operation > Pairing a Bluetooth Device

for more information. Press and hold to turn voice prompts on or off.

E. Link: Press and hold this button to start stereo linking to another Explorer XL. Then,

repeat this process on another compatible speaker. To disconnect the link between the

two speakers, double-press the Link button. See Operation > Linking Two Speakers

for more information.

F. BOOM Button: Press to simultaneously enhance the bass EQ and volume and activate

a light show that pulses to the beat of the music.

G. Radio Button: Press to set the radio to FM1 or FM2, or turn the radio off.

H. Presets: In Radio Mode, press these buttons to select a previously saved preset

station. To save the current station as a preset, press and hold these buttons. See

Operation > Using the Radio to learn more.

I. Tune/Track: Press to tune in a radio station or go to the previous/ next track on a

Bluetooth connected device. To “seek” (jump to the next available radio station), hold

either button down for a few seconds.

J. Play/Pause: Press to play or pause a track from a connected Bluetooth device.

K. Lights: Press to cycle between light modes.

•Solid Mode: Each button will stay lit on a specific color and not change. All 4 FX

pads will be different colors. The Boom Button™will be lit at 20% unless it is pressed,

then it will be fully lit.

•Beat Sync: The lights will flash to the beat of the audio being played through the

speaker.

•Off: The lights turn off except for the button that is being pressed. If the Boom

Button™is pressed when the unit is in lights-off mode, all lights will turn to 100%

brightness until the button is released.

L. FX REC: Press to record up to 30 seconds of your own sound effect. Once the REC

icon begins flashing, press and hold an FX pad to begin recording from any sound

source (such as Bluetooth, radio, or the Inputs) while the pad is held. Once recorded,

press the FX pad to trigger your sound. Press and hold this button and press an FX

pad to delete a recorded sound. Higher volume from your input will result in a higher

quality sound recording. When using the microphone to record a sample, point the

microphone away from the speaker to avoid feedback.

M. FX SELECT: Press to change the sounds on each FX Pad. Once the FX Pads are lit

white, press each one to cycle through all the sound effects. Once you have found the

sound effects you like, press this button again to lock them in. To revert to the default

sounds, press and hold this button. See Operation > Using the FX Pads to learn more.

N. FX Pads: Press these pads to trigger a sound effect. Press the Control Knob and

select INST to adjust the FX volume. See Appendix > Sound FX for a full list of sounds.

O. Microphone Input (1/4” [6.35 mm], unbalanced): Connect a microphone to this mono

input. Press the Control Knob and select MIC to adjust the microphone volume.

P. Instrument Input (1/4” [6.35 mm], unbalanced): Connect an instrument such as an

electric guitar to this mono input. Press the Control Knob and select INST to adjust the

instrument volume.

Q. Aux Input (1/8” [3.5 mm], balanced): This stereo input can be used to connect a CD

player, MP3 player, or other audio source. To hear this signal, disconnect Bluetooth

and enter Aux Mode by pressing the Bluetooth button.

R. USB Charging Port: Connect your device’s charge cable here to charge it. USB

charging only functions when the unit’s power is turned on.

Display Icons

•Charging Indicator ():

oWhen the power cable is connected, the movement of the battery segments

indicates that it is charging.

oWhen the power cable is disconnected, the battery segments show the battery

level.

oWhen the battery level is low, the bottom battery segment will blink.

oIf a front panel button is not pressed within 60 seconds, the battery level

indicator will turn off (to save energy). The battery level indicator will reappear

when any button is pressed. Also, when the battery gets to the lowest battery

icon segment, the battery level indicator will turn back on.

•Power Icon (): The power icon will be lit when Explorer XL is powered on. The

power icon will not be lit when Explorer XL is powered off.

•Lightning Bolt Icon (): The lightning bolt icon will be lit when the power cable is

connected to wall power.

•Link Icon (): The Link icon will be on when linked to another speaker. The Link icon

will be off when a single speaker is used. See Operation > Linking Two Speakers below

for more information.

•Bluetooth Icon ():The Bluetooth icon will be lit when a device is paired to Explorer XL.

•FM Icons: When the Radio is On, this shows whether it is in FM1 or FM2 mode.

•BOOM Icon: The BOOM icon will be on when BOOM mode is activated. The icon will be

off when the function is deactivated.

•REC Icon: The REC Icon will flash when the FX REC button is pressed, indicating that

the Explorer XL is recording from a sound source.

•Mic/Vol: These icons indicate the current function of the Volume Control.

•Radio Station: The numerals in the center indicate the current radio station that is

selected.

Operation

Pairing with a Bluetooth Device

1. Make sure the speaker is within range of your Bluetooth device (no more than 100 ft. /

30.5 m away).

2. Press the Bluetooth button on the speaker.

3. Navigate to your Bluetooth device’s setup screen. Then find and select Explorer XL. If

your Bluetooth device prompts for a pairing code, enter 0000.

Note: Do not connect to Explorer XL_BLE; this is reserved exclusively for connecting to the

ION Sound XP app. If you experience trouble in connecting, select “Forget this Device” on

your Bluetooth device and try to connect again.

Note: If you have previously connected to your Bluetooth device, Explorer XL will reconnect

automatically.

Tip: Press and hold the Bluetooth button to enable or disable the Bluetooth pairing voice

prompts.

To disconnect a paired Bluetooth device, press the Bluetooth button, or turn off Bluetooth

from your device’s Bluetooth settings. This will also enter Aux mode. Double-press the

Bluetooth button to disconnect a paired Bluetooth device and search for a different device.

App Control

IMPORTANT: To ensure the best possible experience with the app, use the most current

Android OS or iOS on your device.

Follow these steps to download the free app on your device:

1. Open the Apple App Store or Google Play on your device. Then, search for the ION

Sound XPTM app.

2. Follow the on-screen instructions to download and install the app. Once downloaded,

the ION Sound XPTM app will appear on your device's home screen.

3. Connect your device to Explorer XL via Bluetooth. See Pairing with a Bluetooth

Device to learn how to do this.

4. Open the ION Sound XPTM app. If prompted, allow the app to access your device's

Bluetooth and Location Services.

5. Tap to select Add A Product on the screen. The app will scan and find Explorer XL.

If you are having issues connecting, tap Help with setting up? for additional tips.

6. Select the Explorer XL icon to gotothe next screen, where you can usethe app to

control various functions ofthe speaker such as:

•Radio: Play the radio, change stations, and edit presets.

•EQ: Adjust the speaker's equalization, and enable ordisable Bass Boost.

•Volume: Adjust the speaker volume and microphone volume.

•Voice Prompts: Enable or disable the voice prompts.

•Link: View instructions for linking Explorer XL to another compatible speaker.

•Support: Visit ionaudio.com,contact Technical Support, and view Warranty

information and Frequently Asked Questions.

Using the FX Pads

Press the FX Select button to toggle between eight different sounds for each of the four FX

buttons: DJ Effects, Drum hits, Crowd Noises, and Party Sounds.

Press the FX Pads to trigger each sound effect. Use the Drum and DJ effects to enhance your

dance party, the Crowd effects to fire up the crowd at the big game, or have a blast with

Party sound effects. See the chart in the Appendix > Sound FX for a full list of sounds.

Linking Two Speakers (stereo)

1. Be sure to disconnect any Bluetooth devices before attempting to link two speakers.

2. Press and hold this button to start stereo linking to another compatible speaker. Then,

repeat this process on the other speaker. See ionaudio.com for a list of compatible

speakers.

3. Once the link has been established, LINK should appear on the Display. Select which

unit will be the primary speaker by pressing its Bluetooth button. Use this speaker for

pairing with a Bluetooth device or selecting a radio station. The primary speaker will play

left channel audio, and the secondary speaker will play right channel audio.

To disconnect the link between the two speakers, double-press the Link button.

Using the Radio

Selecting a radio station:

1. Press the Radio button to select FM1 or FM2.

2. Press either of the Tune/Track buttons to select a radio station.

To “seek” (jump to the next available station), hold either button down for a few seconds

until it starts to seek a station.

Note: Pause playback from or disable Bluetooth entirely before using the radio to prevent both

audio signals from being active at the same time.

Saving a radio station as a preset:

1. Press the Radio button to select FM1 or FM2.

2. Press either of the Tune/Track buttons to select a radio station.

3. Press and hold a Preset button to assign the current station to that preset number. The

display will show “SAV” to show the station has been saved.

Recalling a saved radio station preset:

1. Press the Radio button to select FM1 or FM2.

2. Press a Preset button to select a previously saved preset station.

To turn off the radio, press the Radio button until it is set to Off.

Andere Handbücher für Explorer XL

Inhaltsverzeichnis

Andere ION Sprecher Handbücher

ION

ION Block Rocker Series Gebrauchs- und Pflegehandbuch

ION

ION Solar Sounds Bedienungsanleitung

ION

ION GEODE ROCK SPEAKERS Bedienungsanleitung

ION

ION BLOCK ROCKER BLUETOOTH Bedienungsanleitung

ION

ION Party Boom FX Bedienungsanleitung

ION

ION Pathfinder 4 Bedienungsanleitung

ION

ION EXPLORER EXTREME Bedienungsanleitung

ION

ION Party Rocker Go Bedienungsanleitung

ION

ION Cornerstone Glow Bedienungsanleitung

ION

ION Tahiti Bedienungsanleitung

ION

ION Trailblazer Bedienungsanleitung

ION

ION DUO DECK Bedienungsanleitung

ION

ION Block Rocker Plus Bedienungsanleitung

ION

ION party starter Bedienungsanleitung

ION

ION POWER GLOW 300 Bedienungsanleitung

ION

ION Party Rocker Plus Bedienungsanleitung

ION

ION All-Star Guitar Bedienungsanleitung

ION

ION Pro Glow 8 Bedienungsanleitung

ION

ION Game Day Lights Bedienungsanleitung

ION

ION Planter Bedienungsanleitung

ION

ION SURVIVAL SCOUT Bedienungsanleitung

ION

ION Solar Stone Glow Bedienungsanleitung

ION

ION UBER BOOM Bedienungsanleitung

ION

ION Solar Stone Multi Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung