iPark IPTSF407 Bedienungsanleitung
IPTSF407
FRONT PARKING ASSIST SYSTEM MANUAL
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 1
TABLE OF CONTENTS
1 Important Notice - Disclaimer - About The Product
2 Key Features - Technical Specifications
3 Self-Test Function - Learning Function
4 Attention – Sensor Maintenance - Display Function
5 Packing List - Installation Tools
6,7 Sensor Installation
8 Wiring Diagram
9 ECU Installation
10 Troubleshooting
11 Function Test After Installation
12 Display Installation
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 2
page 1
IMPORTANT NOTICE
iPARK® Parking Assist Systems help to
provide assistance when reversing and
parking.
Driving skills, such as using caution,
slowing down, use of mirrors etc. are
always essential.
1. This unit is for use with 12V DC only.
2. Unit should be installed by a
professional auto technician to avoid the
warranty being voided.
3. Route wiring harness away from heat
sources and electrical components.
4. It is strongly recommended to check
behind the planned location of the
sensors before drilling.
5. Perform a test after installation is
complete.
DISCLAIMER
The parking assist system is designed as
a driver assistance device, and should not
be used as a substitute for safe parking
practices. The area into which the vehicle
is to be reversed must be constantly visu-
ally monitored while parking. The manu-
facturer, its distributors and sales agents,
do not guarantee against or assume
liability for collisions or damages while
reversing your vehicle.
ABOUT THE PRODUCT
This Parking Assist System is an
ultrasonic detection and distance
monitoring system.
It electronically detects the area behind
your vehicle while reversing, and alerts
you with audible tones that quicken and
eventually become a constant tone, if the
system detects an obstacle. If the system
has the optional display, it will show the
distance in FEET, numerically. This is, as
well as, audible tones and progressive
LEDs.
Each part of this product has passed a
stringent test during manufacturing. The
product is designed to operate at a wide
range of temperatures from -40ºF to
+175ºF and becomes very useful when
parking during poor weather conditions.
With the help of a Parking Assist System,
you can enjoy a comfortable and conven-
ient parking experience.
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 1
KEY FEATURES
• Buzzer can be upgraded to various displays (optional),
with built-in audible and display options
• System can be used as a 2 sensor system if desired
• Precise detection range
• Self-Test and Auto Anti-Falsing Alert technology
TECHNICAL SPECIFICATIONS
• Rated Voltage: . . . . . . . . . .12V DC
• Power Consumption: . . . .3.6W
• Working Temperature: . .-20ºC to +70ºC
• Detecting Distance: . . . . .1ft to 6.5ft
• Detecting Angle: . . . . . . .H>60º, V>60º
page 2
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 2
SELF TEST FUNCTION
When reverse gear is selected, the sys-
tem will test the rear sensors
automatically.
If all sensors are working correctly, the
unit will beep once.
If a damaged or defective sensor is
detected the unit will beep three times.
Other sensors will continue to function
normally.
LEARNING FUNCTION
When programming, the system
confirm there are no other objects with-
in 10 feet of the vehicle. Install the
system per instructions. Temporarily
connect the Green programming wire to
the brake wire. Turn the ignition key to
the ON position; piezo will beep 1 time.
Depress, and hold the Brake pedal.
After 5 seconds piezo will beep 2 times
indicating the learning process is
complete.
Release the brake pedal, turn the
ignition OFF, and disconnect the Green
programming wire.
Check the system to confirm correct
operation.
Once learned, the sensor(s) are
programmed to ignore the Tow Bar, or
Spare Tire and will not detect them and
the other sensors will retain normal
operation.
page 3
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 3
-
ATTENTION
False detection may occur in the
following situations.
• Angled or sloped walls or objects may
deflect the ultrasonic signal.
• Soft fabrics, carpeting or padded sur-
faces may absorb the ultrasound and
not give an accurate reading.
• Buildings with staggered walls or
insets may also absorb or deflect the
signal.
• Heavy Rain, dirty or damaged sensors
may also cause false warnings.
SENSOR MAINTENANCE
Do not wash the sensors with a
pressure washer or scrub them forcibly.
Avoid wax or grim buildup in the
sensors. Wash the sensors with water in
a low pressure manner.
Please allow the ice to melt by
applying water when sensors are
covered with frozen ice.
AUDIBLE BUZZER FUNCTION
3FT to 2FT – Slow BEEP—BEEP—BEEP
2FT to 1FT – Faster BEEP BEEP
1FT to 0FT – Constant BEEEEEEP
page 4
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 4
PACKING LIST
4 Sensors (Plastic Bumper) 1 Control ECU Module
4 Sensor Extension Cables 1 Slim Display
1 Power Harness 1 Hole Saw
1 Square Two-Faced Mounting Tape 1 Manual
* Estimated installation time: approximately 30-60 minutes
INSTALLATION TOOLS
Power Drill Tape Measure
Electrical Tape Scissors
Soldering Iron / Solder Hole File
Screw Driver Skill Knife
page 5
IMPORTANT –The installation must be completed outdoors, 10 FEET clearance of any objects or buildings etc.
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 5
SENSOR INSTALLATION
Please adjust the sensors angle to be
parallel to the ground surface
depending on the height and angle of
the mounting surface. Ideal mounting
height is between 18 to 25 inches.
Position the 4 sensors to be equally
spaced apart on the bumper. Best
location is outer two sensors spaced 8 to
10 inches in from outer edge of vehicle.
Measure the distance between the two
sensors, and divide by three to be
location for the other two sensors.
page 6
SENSOR INSTALLATION
WHEN BUMPER IS REMOVED
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 6
A
C
B B A
TAPE
SENSOR INSTALLATION (Continued)
DIRECT ON VEHICLE BUMPER
page 7
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 7
DISPLAY
MAIN BOX
EROSNES
4 SENSORS - INSTALL ON FRONT BUMPERS
GREEN - LEARNING +12V
PINK - IGNITION +12V
BLACK - GROUND -12V
PURPLE - BRAKE +12V
RED - REVERSE +12V
FR
O
SNES
GROSNES
H
RO
SNE
S
WIRING DIAGRAM
Learning (+)12V DC (During Learning)
Reverse (+) 12V DC (For Front/Rear Protection)
Ignition (+) 12V DC
Foot Brake (+) 12V DC
Buzzer (-) Ground - Black
Sensors E F G H
Wiring Diagram for 4 Sensor Front System
page 8
iPark_IPTSF407_Manual_Layout 1 11/10/14 11:30 AM Page 8
Inhaltsverzeichnis
Andere iPark Autozubehör Handbücher
