IPEX CABLINE-VS II PLUG Bedienungsanleitung

1/ 16

Document No.

ASM

005

Confidential C

PEX Inc. QKE

DFFDE09

04 REV.8

CABLINE®-VS II PLUG

Part No. 20846

Assembly Manual

1 S19446 July/22/’19 M.Nakamura T.Masunaga H.Ikari

0 S17557 Aug./02/’17 K.Baba T.Kurachi Y.Shimada

Rev. ECN Date Prepared by Checked by Approved by

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

2/ 16

Confidential C

1.Purpose：

This manual is to explain the soldering method / process of the CABLINE-VS II PLUG with cable, and assembly of

LOCK BAR ASS’Y, SHELL A.

2.Applicable connector：

Name: CABLINE-VS II PLUG

Parts No.:

Set P/N CABLE ASS’Y 20846-030T-01

Discrete P/N

HOUSING ASS’Y 20847-030T-01

LOCK BAR ASS’Y 20848-030T-01

SHELL A 3427-0301

3.Fixtures：

3.1 Components and Instruments used in the condition confirmation

・Pulse heater

・Heater chip

30P

Thickness 0.5

Width 15.0

Unit: mm

・Recommended solder bar

Resin-free solder made by Uchihashi Estec Co., Ltd. was used.

Positions 30P

Solder size

AWG#32～#38 φ0.14

AWG#40～#44 φ0.1

Length 15.0mm Ref.

Unit: mm

Name P/N Manufacturer

Reflow head NA-66 Nippon Avionics Co., Ltd.

Pulse heat power supply TCW-215 Nippon Avionics Co., Ltd.

-0.05

-0.03

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

3/ 16

Confidential C

4. Recommended pulse heat condition

MICRO-COAX

①Idle temp. 150℃

②1st heat temp. 220℃

③ 〃 rise time 0.5sec.

④ 〃 holding time 3.0sec.

⑤2nd heat temp. 300～320℃

⑥ 〃 rise time 0.5sec.

⑦ 〃 holding time 3.0sec.

Heater tip Pressure 5～10N

※This pulse heat condition was evaluated and confirmed by our pulse heat jig and instruments. The most optimum condition may change

based on the shapes of pulse heat jig and instruments, the environments, or other reason.

Therefore, please examine the pulse heat condition adequately in advance of use.

①

1st heat 2nd heat

②

⑤

(℃)

③ ④

⑥

⑦(sec.)

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

4/ 16

Confidential C

5.Work procedures：

5-1. Soldering of center-conductor

①The cables have to be fabricated as shown below in advance of soldering.

Recommended MICRO-COAX CABLE dimension

MICRO-COAX dimension

MICRO-COAX AWG#**

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

5/ 16

Confidential C

Recommended DISCRETE CABLE dimension

DISCRETE AWG#**

DISCRETE dimension

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

6/ 16

Confidential C

②Apply flux to contact by the dispenser etc., and please confirm all contacts were applied flux.

Photo.1 After applying flux

※Please do not apply flux too much like Photo.2. It can cause flux splash or leak to the mating area.

Photo.2 Extra flux

※Washer must not be used to take flux off because it may cause flux attached to mating area.

Applying Flux area

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

7/ 16

Confidential C

③Pre-set and locate solder bar at center of connector (HSG ASS’Y).

Fig.1 Set of solder bar

④Set the cable.

※Setting discrete cable is to protect 0.2MAX. as Fig.3. There is danger that Center Conductor touch SHELL.

Fig.2 Set of cable

Fig.3 Setting Discrete Cable

0.2 MAX.

Solder Bar

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

8/ 16

Confidential C

⑤Center-conductors are soldered with pulse heater. See photo.3 of soldering condition.

Photo.3 AWG#40

Caution: The SHELL bottom side of PLUG HSG ASS'Y has convex shape at the points shown in Fig.4, so please make escape shape on

the receiving jig of the pulse heater to prevent interference.

Fig.4 The SHELL bottom side of PLUG HSG ASS'Y

※When solder bridge is appeared between the terminal, try heating again with pulse heater only one time.

If the bridge isn’t repaired, use the soldering iron only a NG point.

Condition of Soldering iron ： 50W

Operating temperature ： 350℃

Application time of soldering iron ： Within 5sec.

※Because it might give product damage, please do not instigate a cable after soldering.

※When there might be the short circuit with SHELL-A, put an insulating tape in SHELL-A before assembly of SHELL-A.

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

9/ 16

Confidential C

Caution: Do not forcedly pull the cable toward red arrow direction after soldering or apply excessive load on the soldered area,

or it may peel the solder. [Fig. 5]

Fig.5 Cause of solder peeling

◆Insulating tape thickness t=0.06mm

Please aim at the round end part of SHELL-A and paste Insulating tape.

If you paste it far from the round end part, It might cause the SHELL-A float.

Insulating tape

CABLINE

VS II PLUG

Assembly Manual

Document No.

ASM

005

10 / 16

Confidential C

5-2. Cautions in treating SHELL A

SHELL A is delivered in the reel with a carrier. The following is the method to cut SHELL A from Carrier.

①Cut carrier on the cut line of the left below picture (green line) by a scissors for metal.

②Hold the center of Plug shell-A and cut it off from Notch by ±45 deg of reciprocating work.

When it does not be cut, try again this reciprocating work.

After separated, check there is no burr around the cut part.（Photo.7）

Plug SHELL A Detail of Notch

Caution: By pulling like the photo below to cut off by force (Red arrow direction), burrs and transformation can be caused.

Carrier

Notch

Photo.4 Before cut Photo.5 After cut

Cut Line

Photo.6 Cut condition Photo.7 After cut

Without burrs

45°

Photo.8 Bottom side view Photo.9 Upper side view

Photo.10 Cut by force (Bad example)

Dieses Handbuch passt für folgende Modelle

Andere IPEX Kabel und Steckverbinder Handbücher

IPEX

IPEX CABLINE-UY Bedienungsanleitung

IPEX

IPEX MHF-TI Bedienungsanleitung

IPEX

IPEX CABLINE-VSF Bedienungsanleitung

IPEX

IPEX ISH20P Bedienungsanleitung

IPEX

IPEX MHF-A Bedienungsanleitung

IPEX

IPEX NOVASTACK 35-HDN Bedienungsanleitung

IPEX

IPEX EVAFLEX 5-SE-GHT Bedienungsanleitung

IPEX

IPEX CABLINE-VS Bedienungsanleitung

IPEX

IPEX NOVASTACK 35-HDP Bedienungsanleitung

IPEX

IPEX CABLINE-CA PLUG Bedienungsanleitung

IPEX

IPEX ISH VW Bedienungsanleitung

IPEX

IPEX AP-10 Bedienungsanleitung

IPEX

IPEX CABLINE-CX II With Cover Bedienungsanleitung

IPEX

IPEX MINIFLEX 175-ST Bedienungsanleitung

IPEX

IPEX CABLINE-VS IIF Bedienungsanleitung

IPEX

IPEX MHF 7S Bedienungsanleitung

IPEX

IPEX MINIFLEX 2-BF LK Bedienungsanleitung

IPEX

IPEX CABLINE-CA II PLUS Bedienungsanleitung

IPEX

IPEX CABLINE-VS PLUG Bedienungsanleitung

IPEX

IPEX NOVASTACK-B Bedienungsanleitung

IPEX

IPEX MP-A01 Bedienungsanleitung

IPEX

IPEX CABLINE-CBL PLUG Bedienungsanleitung

IPEX

IPEX MINIFLEX 2-BF Bedienungsanleitung

IPEX

IPEX ISH Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung