IQ DefinePro Bedienungsanleitung

Deﬁne Set-Up Instructions

1. First, remove the battery insulator from the RED laser.

2. Mount the sight to the bow with the supplied hardware. (ﬁgure 1 a.)

3. Sight in top pin to 20 yards.

4. Hang supplied target at 20 yards to zero RED laser to sight.

5. Turn on RED laser to align to 20 yard pin on supplied target.

6. While holding 20 yard pin on zeroing target, determine

where RED laser is striking the target.

7. Depending on where your RED laser is impacting left and right

of the target, use the set screws (ﬁgure 1 b.) to align

the RED laser with the lower dot on the zeroing target.

(this may take a few attempts to get the laser directly below the pins on the zeroing target)

8. Alignment must always be checked at full draw.

9. Once the RED laser is directly in-line vertically with the pins, adjust the elevation. (ﬁgure 2)

10. To adjust the vertical elevation, slightly loosen the upper and lower mounting screws.

There should still be pressure on the bow sight but still allows the sight to move up and down.

11. Adjust the set screw clockwise to move the RED laser down.

Adjust the set screw counterclockwise to move the RED laser up.

12. Use the set screw to make vertical adjustments until the RED laser is

impacting the lower dot and the 20 yard pin is held on the upper dot.

(This may take a few iterations to complete)

13. Once this is complete, re-tighten your sight mounting screws.

14. Re-sight in your 20 yard pin.

15. Remove the RED laser. This is easily done removing the two machine screws.

*IQ does not condone hunting with the laser attached.

Please follow all Local and Federal hunting regulations.

16. Time to Adjust the Retina Lock. Flip over for instructions.

Activation of range ﬁnder

1. Unscrew the battery cover on the bottom of the sight and remove

the battery insulator.

2. Connect the trigger switch to the range ﬁnder port. (ﬁgure 3)

3. Mount the trigger switch to your preferred mounting location.

4. Depress the trigger once to activate the range ﬁnder to standby mode.

Depress the trigger a second time to put the range ﬁnder into scan mode.

Depress the trigger a third time to lock in desired range.

Depress a fourth time to return to scan mode.

*Accurate scans are done at full draw, using the 20 yard pin.

5. Scan mode will deactivate to standby mode after 2 minutes of no usage.

6. Standby mode will automatically shut off after 1 minute.

Pin Light LED

1. Depress the light switch on the side of the ranger ﬁnder to active pin lights. (ﬁgure 4)

2. There are 4 levels of pin brightness.

3. Pin light will automatically shut off after 1 hour.

Before mounting and setting up the Deﬁne, familiarize yourself

with the diagrams on the back of these instructions. They will be

a helpful tool to reference during set up.

Once set up is complete, the range ﬁnder is calibrated to the 20 yard pin.

When ranging a target on the range or in the ﬁeld, use the 20 yard pin to mark

the target, then shoot using the appropriate pin.

The laser attachment on the Deﬁne is precision machined to align with

the scanning eye on the range ﬁnder. To ensure the Deﬁne marks the

desired target, it is imperative to follow these simple set up instructions.

ﬁgure 1

Left adjust Right adjust

Mounting holes

ﬁgure 2

Vertical adjust set screw

* when you move the set screw counterclockwise, you need to push

the laser up as the set screw is creating room for the sight to pivot

ﬁgure 3

Light switch

ﬁgure 4

Trigger button

These are adjusted at the same time

* loosen mounting screws before adjsuting.

Adjust Left

rear set screw clockwise

front set screw counterclockwise

Adjust Right

rear set screw counterclockwise

front set screw clockwise

PRO

socket cap hex screw

split washer and washer

at head hex screw

Laser

*Never adjust these screws.

They are pre-calibrated for the DEFINE PRO.

Battery located in the back

Micro adjust Windage and Elevation dials

The Micro Adjust Windage and Elevation Dials allow

the shooter to make small, consistent, and accurate

adjustments as needed. They are also useful tools for

precision sight in.

Elevation dial

The laser etched Elevation Dial

precisely adjusts the pins up and

down. (clockwise moves pins down,

counterclockwise moves pins up)

Windage dial

The laser etched Windage Dial

precisely adjusts the pins left and right.

(clockwise moves pins right,

counterclockwise moves pins left)

Built in LED pin light

The built in pin light features

4 different intensities. Each

successive click brightens the

pins.

*Pins can be removed if archer prefers more open optics

by completely removing the machine screw on the

preferred pin and gently removing the pin housing

from the bezel.

Mounting holes Tool-free locking knobs

Vertical adjust set screw

Left adjust

Right adjust

Trigger Trigger plug in port

Fully captured .019” pins

Used to align 20 yard pin to laser during mounting and set up.

- Adjust clockwise to move laser down.

- Adjust counterclockwise to move laser up.

Used to align 20 yard pin to laser during mounting and set up

These are adjusted at the same time.

Adjust Micro adjust Winadge and Elevation dials without tools.

Adjust Left

rear set screw clockwise.

front set screw counterclockwise.

Adjust Right

rear set screw counterclockwise.

front set screw clockwise.

Depress the trigger once to activate the range ﬁnder to standby mode

Depress the trigger a second time to put the range ﬁnder into scan mode.

PRO

a) If you see the green Retina Lock™,

adjust the green Retina Lock™ until the

black dot is centered within the green

Retina Lock™ using the micro adjustments

located on the top and side of sight.

Remember you are adjusting the green

Retina Lock™ to ﬁt your form/anchor point.

Repeat this step until the black dot is

centered in the green Retina Lock™ – at

your form/anchor point.

b) If you don’t see the green Retina Lock™

at your form/anchor point you will need to

move your anchor point up or down and

possibly left or right until you ﬁnd the

green Retina Lock™. Once you’ve

determined the direction of the green

Retina Lock™, use the micro adjustments

located on the top and side of sight to

adjust the green Retina Lock™ to ﬁt your

form/anchor point. The micro adjustment

on the top of the sight is to move the green

Retina Lock™ up and down and the micro

adjustment on the side of sight is to

move the green Retina Lock™ left and

right – REMEMBER YOU ARE MOVING

THE GREEN Retina Lock™. Repeat this

step until the black dot is centered in the

green Retina Lock™ – at your form/

anchor point.

Once your top pin and range ﬁnder are

accurately calabrated, it’s time to adjust

your Retina Lock™.

Draw your bow using the same

form/anchor point used to set your top pin

and look for the green Retina Lock™.

Set Up

micro adjustments

Up/DownLeft/Right

Once your black dot is centered in

the green Retina Lock™

AT YOUR FORM/ANCHOR POINT you can

now sight your pin in at other distances

and make your distance marks.

Quiver mounting holes

laser

20 yrd pin

SIGHT IN PAPER

PRO

Andere IQ Messgerät Handbücher

IQ IQ150 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung