ISystem IC50000-CI Bedienungsanleitung

iC5000 CI BlueBox

User Manual

V1.3

This document and all documents accompanying it are copyrighted by iSYSTEM AG and all rights are

reserved. Duplication of these documents is allowed for personal use. In all other cases, written consent

from iSYSTEM is required.

All trademarks are property of their respective owners.

www.isystem.com

Contents

iC5000 CI BlueBox

Important safety notice ......................................................................................................................... 5

Package content ...................................................................................................................................... 6

Specifications ........................................................................................................................................... 7

Operation ................................................................................................................................................... 8

Device description ..............................................................................................................................................................................................................9

Connecting the iC5000CI to the Target ...........................................................................................................................................................11

Accessories ............................................................................................................................................. 14

Declarations ............................................................................................................................................ 16

User Notes .............................................................................................................................................. 17

iC5000 CI BlueBox

iC5000 CI BlueBox On-Chip Analyzer - Hardware platform which allows hardware debugging

and testing a wide range of embedded microcontroller platforms that are based on a variety of

processor architectures and is implemented into Continuous Integration (CI) infrastructures.

iC5000 CI comes with almost the same functionality as the standalone products and is

licensed on yearly subscription basis.

Continuous Integration (CI) - A combination of iSYSTEM BlueBox hardware, software and

consulting services on how to setup the hardware and software of a CI infrastructure, which is

based on building test racks with multiple hardware setups – each consisting of the

embedded target hardware and iC5000/iC5700 CI.

winIDEA IDE - Integrated Software Development Environment delivers the visual insights

required to debug the embedded application, performs timing analysis, measures code

coverage, visualizes RTOS task states and much more. More information

isystem.com/winideaide.

testIDEA - The testIDEA environment simplifies the development of unit tests for embedded

applications. More information isystem.com/testidea.

isystem.connect - Application programming interface (API) with Software Development Kit

(SDK) and supporting a variety of programming languages makes almost the entire range of

features provided by our software, such as winIDEA, its Analyzer and testIDEA, and the

capabilities of our hardware development tools, such as our BlueBox technology and their IOM

accessories. More information isystem.com/sdk.

iSYSTEM's solutions run under Microsoft® Windows®, GNU, Linux OS; or optionally within the

Eclipse environment via a plugin. Software can be downloaded from the Downloads page at

http://www.isystem.com.

Important safety notice

General safety instructions - Please read the following safety precautions carefully before putting

this device to use to avoid any personal injuries, damage to the instrument, or to the target system.

Use this instrument only for its intended purpose as specified by this manual to prevent potential

hazards.

Use included power cord and power supply - The enclosed power supply has been approved for

use by iSYSTEM. Please contact iSYSTEM if you need to consider an alternative power.

Use grounding wire - Prior to applying power to either the BlueBox or the target, connect the device

and the target system together with the included grounding wire. This is to avoid potential damage

caused by any voltage difference between the device and the target system.

Use proper overvoltage protection - Please ensure proper protection to avoid exposing the

BlueBox device or the operator to overvoltage surges (e.g. caused by thunderstorm, mains power).

Do not operate without cover - Do not operate the device with cover removed.

Avoid circuit and wire exposure - Do not touch exposed components or wires when the device is

powered.

Do not operate with suspected damage - If you suspect damage may have occurred, the BlueBox

device must be inspected by qualified service personnel before further operation.

Do not operate the device outside its rated supply voltage or environmental range - Consult

with iSYSTEM before using equipment outside of the parameters provided in this manual.

This symbol is used within the manual to highlight further safety notices.

Package content

The standard iC5000 CI order is delivered with the following components:

iC5000 CI with

pre-assembled DTM

module

25 cm 40-pin ribbon cable

Power supply

Ordering code:

IC50000-CI

Ordering code:

IC50020-25

Ordering code:

IC30000-PS

USB 2.0 cable

Ethernet cable

Grounding wire

Ordering code:

BB-USB20-180

Ordering code:

BB-ETHCAT5-200

Ordering code:

BB-WIRE

User Manual

Specifications

GENERAL

Operating temperature

10°C to 40°C

Storage temperature

-10°C to 60°C

Humidity

5% to 80% RH

MECHANICAL

Size

122 x 127 x 45 mm (W x D x H)

Weight

approx. 500g

OPERATION

Communication

interfaces to PC

USB 2.0, 10/100 Mbps Ethernet

Supply voltage

10V to 24V DC

Power consumption

< 8W

ELECTRICAL

Debug signal valid

input voltage range

1.8V to 5.5V DC

Debug signals

47 series termination/protection resistors, ESD protection devices.

Depending on the specific debug adapter, termination might be

different from 47 on some critical signals.

All inputs except the

TDO

10 kOhm pull-up resistor

TDO input

10 kOhm pull-down resistor

TMS and TDI debug

signals

10 kOhm pull-up resistor

RESET

1 kOhm pull-up resistor, buffer-driven to prevent current flow into an

unpowered iC5000 from a powered target board

TAR_VREF (target

reference voltage) pin

100 kOhm input impedance

Operation

Device overview

Device description

The top face of the iC5000 CI features:

A – Debug Trace Module (DTM) provides two connectors, marked #1 and #2. These

connectors are the interface to the target microcontroller. Depending on the target

microcontroller debug features, the supplied ribbon-cables will need to be connected to either

connector #1 only or connectors #1 and #2.

B – The indicator lights provide the status of the hardware:

Power Indicator

On – Powered on

Off – Powered off

R – Running Indicator

On – Target microcontroller is executing code

Off – Target microcontroller is halted

F –Free Indicator

On – BlueBox is available for a connection from a host PC

Off – Active connection to the BlueBox from a host PC exists

The front face of the iC5000 CI features:

C – The grounding socket (marked GND) should be used, together with the supplied Grounding

wire to create an electrical connection between the BlueBox and the target circuitry. The socket

is suitable for a 2 mm Multi Contact Plug (also known as a Banana Plug) if building a longer

or a replacement cable on your own.

The rear face of the iC5000 CI features:

D– Power Switch

E – Power Supply Socket

The socket and plug are latching to stop the plug from being accidentally pulled out of the

socket. To remove the power plug from the socket, always pull gently of the sleeve of the plug

and never on the wire.

F – 10/100 Ethernet Socket

G– USB 2.0 Socket

It is recommended to use the supplied USB 2.0 cable delivered with your iC5000 as it has been

confirmed to fulfill the maximum USB 2.0 transfer rate. Use of alternate cables must be

undertaken at your own risk. The USB 2.0 interface provides the highest possible data transfer

rate of the two available interfaces. It is highly recommended to use the USB 2.0 when using

the trace feature due to the quantity of data to be uploaded to the PC.

Both the 10/100 Ethernet Socket and the USB 2.0 Socket can be connected to a network/PC

simultaneously. The active interface will be determined by whichever interface winIDEA

connects to first.

When powering on the system, switch the BlueBox unit on before powering on the

Target. When powering down the system, power off the Target before powering off the

BlueBox unit!

FBridge port is not Ethernet port!

Use only original iSYSTEM accessories for powering and connecting with the BlueBox

unit. Consult with iSYSTEM before attempting to use any other accessory.

Differences between BlueBox CI and BlueBox

BlueBox CI

BlueBox

Business Model

Subscription

Perpetual or Subscription

System price

***

Debug & Test functionalities

via winIDEA GUI

Debug & Test functionalities

via SDK APIs

For more information refer to sales@isystem.com.

Inhaltsverzeichnis

Andere iSystem Messgerät Handbücher

iSystem

iSystem Infineon Bedienungsanleitung

iSystem

iSystem Infineon SGBT Bedienungsanleitung

iSystem

iSystem Aurora MPC5 Series Bedienungsanleitung

iSystem

iSystem Infineon AGBT Bedienungsanleitung

iSystem

iSystem DAP over CAN Bedienungsanleitung

iSystem

iSystem IC57164 Bedienungsanleitung

iSystem

iSystem Aurora RH850 Bedienungsanleitung

iSystem

iSystem iC5000 Bedienungsanleitung

iSystem

iSystem IC57163 Bedienungsanleitung

iSystem

iSystem IC57163 Bedienungsanleitung

iSystem

iSystem ARM HSSTP Bedienungsanleitung

iSystem

iSystem iC5000 Anwendungshandbuch

iSystem

iSystem iC5000 Anwendungshandbuch

iSystem

iSystem iC5700 Bedienungsanleitung

iSystem

iSystem iC5500 Anwendungshandbuch

iSystem

iSystem C6000 BlueBox Bedienungsanleitung

iSystem

iSystem iC5000 CI BlueBox On-Chip Bedienungsanleitung

iSystem

iSystem Aurora MPC5 Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

iSystem IC50000-CI Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken