ITI Quik Bridge Bedienungsanleitung

Page 1

INSTALLATION

INSTRUCTIONS

Quik Bridge® Supervised One-Channel Receiver

Product Summary

The Quik Bridge®Supervised One-Channel Receiver

adds wireless capability to a compatible hardwired

control panel. Up to two ITI wireless sensors can be

monitored using two zone inputs on the control panel.

One zone input is used for alarm and tamper activa-

tions, while the other zone is used for low battery and

supervisory monitoring (see Figure 1).

Figure 1. Expanding zones by adding up to two

supervised sensors

FIR ST

PANEL

ZO N E

9216G 01A .D S F

SECO ND

PANEL

ZO N E

ALARM

RELAY

SUPER-

VISE

RELAY

ALARM /TAM PER

TRANSM ISSIONS

O ALARM RELAY

LOW BATTERY/

SUPERVISE

TRANSM ISSIONS

TO SUPERVISE RELAY

How the Receiver “Supervises” Wireless

Devices

In addition to alarm and tamper messages, ITI sensors

also transmit low-battery and supervisory messages.

The Quik Bridge One Channel Receiver carefully

“supervises” all of these messages. Alarm and tamper

messages activate the alarm relay, which triggers an

alarm. Low-battery messages activate the supervise

relay and cause the receiver LED to flash every 4 sec-

onds as a trouble indicator. Supervisory transmissions

do not activate any zone or relay, they simply let the

receiver know that the sensor is working properly. If

the sensor stops sending supervisory information,

however, the supervise relay of the receiver is acti-

vated and the LED double-flashes every 4 seconds. If

this coincides with a low-battery condition, the

receiver will triple-flash every 4 seconds.

LED Indicator

The receiver has one LED. Table 1 lists the possible

states of the LED and what they mean.

Table 1. What the states of the LED mean

Power LED Means

On and flickering

irregularly Receiver has power and is receiving

transmissions.

Off Receiver has no power OR

all devices were successfully

deleted from the receiver memory

and the LED will flash on again

within three seconds.

Flashing regularly Receiver is ready to learn a wireless

device.

Flashing once

every 4 seconds Indicates a low battery trouble con-

dition for at least one sensor.

Double-flashing

once every 4 sec-

onds

Indicates that no supervisory trans-

missions have been received in the

past 24 hours from one sensor, or

that no transmissions have been

received from either sensor.

Triple-flashing

once every 4 sec-

onds

Indicates simultaneous low battery

trouble condition and no supervi-

sory transmissions in the past 24

hours (for one or both sensors).

Quik Bridge®

Supervised One-

Channel Receiver

Document Number: 466-1699 Rev. A

October, 1999

9217G07A.DSF

60-760-01-95R

Page 2

Quik Bridge® Supervised One-Channel Receiver

Zone Planning

This section explains the capabilities, limitations, and

suggested uses of the Quik Bridge Supervised One-

Channel Receiver.

Possible Combinations of Wireless

Devices

The receiver can learn and supervise up to two sen-

sors.

What the Wireless Devices Can Do

Table 2 describes how ITI sensors work with the

receiver. The shaded area represents the low battery

and supervisory transmissions to the supervise relay.

Use this information, together with the panel installa-

tion instructions, to plan the installation of wireless

devices.

Planning the installation

Before you begin programming, it is a good idea to

write down how you plan to use the wireless devices

with each zone. Use Table 3 as a work-sheet.

Table 2. Use the information in the table below to plan your installation

of wireless devices.

This device… When this event happens… Has this effect on the receiver…

PIR motion sensor

(all ITI models) Motion is detected or tamper switch is

tripped Activates the alarm relay for a minimum of 3

seconds

Smoke sensor

(60-506-319.5 only) Smoke is detected (no tamper switch) Activates the alarm relay for a minimum of 3

seconds

Panic sensor

(60-578 only) Panic button is pressed (no tamper

switch on panic sensors) Activates the alarm relay for a minimum of 3

seconds or until the button is released, which-

ever is last

Door/window sensor Opening the door

or tripping the tamper switch Activates the alarm relay for a minimum of 3

seconds or until the door is closed

Closing the door (if door was opened)

or resetting the tamper switch (if tamper

switch was tripped)

De-activates the alarm relay

Any sensor added to the mem-

ory of the receiver Battery is low and/or

sensor is not transmitting

supervisory information

Activates the supervise relay for a mini-

mum of 3 seconds

LED will single-flash, double-flash, or

triple-flash every 4 seconds as a trouble

indicator (see “What the states of the

LED mean” on page 1)

Battery is replaced (if the battery

was low) or supervisory transmis-

sions resume (if the sensor was not

transmitting)

De-activates the supervise relay

Page 3

Quik Bridge® Supervised One-Channel Receiver

Sensor Compatibility

The following current ITI Learn Mode™ wireless

devices are compatible with this receiver:

PIR motion sensors

Smoke sensors (60-506-319.5 only)

Panic sensors (60-578 only)

Door/window sensors (see note below)

Note: Only the internal reed switches of a door/win-

dow sensor can be used. The receiver does not

support the use of sensors with external devices

connected to the sensor terminal block.

Control Panel Compatibility

The receiver will expand one zone of any conven-

tional hardwired control panel.

Note: The receiver should not be connected to pow-

ered zones (such as 2-wire smoke zones).

Overview of Receiver Operation

Figure 2. Parts of the Receiver

Programming Button

Use the programming button (see Figure 2) when

doing the following procedures:

“Deleting All Wireless Devices” on page 6

“Adding Wireless Devices” on page 6

Table 3. Zone assignments for wireless devices

Panel

Zone

(supervising)

Panel

Zone

(alarm) Devices Functions

_________________________________________

9216G 03A .D S F

LED INDICATOR PRO GRAM M ING

BUTTON

TERM INAL STRIP

SUPERVISE RELAY N/O

SUPERVISE RELAY COM M ON

SUPERVISE RELAY N/C

ALARM RELAY N/O

ALARM RELAY CO M M ON

ALARM RELAY N/C

+12 V D C

GROUND

1 2 3 4 5 6 7 8

Page 4

Quik Bridge® Supervised One-Channel Receiver

Zone Outputs

The receiver has eight terminals. Terminals 1 and 2

are for +12 VDC power input. Terminals 3–5 are the

alarm outputs that you connect to the desired panel

zone input. Terminals 6–8 are the supervision outputs

that you connect to the desired panel zone input. The

zones can be configured to be normally closed (N/C)

or normally open (N/O) (see “Connecting the

Receiver to a Control Panel” on page 7).

Tools and Accessories Needed

Included with Receiver

Four 1½'' screws

Wall anchors

Not Included with Receiver

Drill with assorted bits

EOL resistors (usually supplied with the panel)

Phillips screwdriver

Voltmeter

Wire stripper

Installation Guidelines

Observe the following guidelines when installing the

receiver:

Leave ten inches above the receiver for the

antenna.

Avoid areas that are likely to expose the receiver

to moisture.

Avoid areas with excessive metal or electrical

wiring, including furnace and utility rooms.

Avoid mounting the receiver on a metal surface.

When mounting on metal is unavoidable, mount

the receiver so that the antenna extends above the

metal surface (see Figure 2)

The One-Channel Receiver is a super regenera-

tive receiver. To ensure consistent operation of

the receiver, mount it at least three feet away

from other super regenerative receivers (such as

the receiver in most garage door openers).

Figure 3. When mounting on metal is unavoidable

Installation

This section explains how to install the Quik Bridge

Supervised One-Channel Receiver.

Mounting the Receiver

CAUTION: You must be free of static electricity

before handling circuit boards.

Touch a bare metal surface or use a

grounding strap to discharge your-

self.

To mount the receiver on a wall:

1) Choose a location for the receiver. You can

mount the receiver on a sheetrock wall, but you

may need to use additional mounting hardware.

METAL METAL

8836G02A.DSF

Page 5

Quik Bridge® Supervised One-Channel Receiver

2) Remove the cover by pressing down on the center

of the top edge of the cover (see Figure 4).

Figure 4. Removing the cover

3) Hold the receiver against the wall at the desired

height and location, leaving at least ten inches

above the base for the antenna. While holding the

receiver against the wall, mark the location of the

top-left and lower-right mounting holes.

4) Remove the base from the wall and install wall

anchors at any marked location where studs are

not present.

5) Secure the receiver to the wall using two 1½''

Phillips screws (included).

6) Secure the antenna to the wall using a T-18 staple

gun and 9/16” staples.

Powering the Receiver

CAUTION: You must be free of all static elec-

tricity when handling sensors. Touch

a grounded metal object before han-

dling the circuit board.

You must connect the receiver to the +12 VDC power

outputs on the panel or to a separate power supply

(such as 12-volt DC adapter).

Note: If you choose not to connect the receiver to the

panel power outputs, consider using a power

supply with a back-up battery (in case of power

outages).

To find the DC power terminals on the panel, see the

panel installation instructions.

To power the receiver:

1) Shut off or remove power from the panel.

2) Using Figure 5 as a guide, connect the receiver to

the panel or other equivalent power supply.

Figure 5. Connecting power to the receiver

9217G07A.DS

9217G02A.DSF

SCREW MOUNTING HOLES

9216G 08A .D S F

PANEL AUXILIARY

PO W ER TERM INALS

O R +12 V D C

PO W ER SUPPLY

RECEIVER POW ER TERMINALS

+12 V D C

GROUND

+12 V D C

GROUND

345678

Page 6

Quik Bridge® Supervised One-Channel Receiver

Programming

This section explains how to add and delete wireless

devices from the memory of the Quik Bridge Super-

vised One-Channel Receiver.

Deleting All Wireless Devices

Delete all wireless devices from the memory of the

receiver before you begin adding any new ones.

Deleting all wireless devices clears the memory of the

receiver. This prepares the receiver for new program-

ming.

Note:It is not possible to delete devices one at a time.

To delete all wireless devices from the receiver:

1) Press and hold the programming button. In about

three seconds you will hear and feel a “double-

click” from the receiver. Continue holding the

programming button until you hear a second dou-

ble-click from the receiver (3 seconds) and the

LED shuts off.

2) Release the programming button. The LED will

flash twice, indicating that the receiver memory

is cleared.

Adding Wireless Devices

See “Sensor Compatibility” on page 3 for information

on compatible ITI wireless devices.

To add a wireless device to the receiver:

1) Press and hold the programming button until you

hear and feel a “double-click” from the receiver

(about three seconds), then release the program-

ming button.

2) Wait three seconds. The LED will begin flashing,

indicating the receiver is ready to learn a new

wireless device.

Note: If the LED is not flashing, the receiver is not

ready to learn a device. Always wait until the

LED begins flashing before proceeding to the

next step.

3) Trip the device while holding it at arm length

from the receiver:

For sensors with tamper switches

Activate the tamper switch by removing the

cover.

For sensors without tamper switches

Put the sensor in alarm.

4) After about three seconds, the receiver will dou-

ble-click to indicate that the wireless device was

added.

5) To add another wireless device, go back to step 1.

Page 7

Quik Bridge® Supervised One-Channel Receiver

Connecting the Receiver to a

Control Panel

Connect the receiver zone output terminals to the zone

input terminals on the panel. The receiver zone may

be configured to be N/C (Normally Closed) or N/O

(Normally Open). See figures 6 and 7 for wiring and

EOL resistor placement.

Figure 6. Wiring a receiver zone to be N/C

Testing

This section explains how to test the operation of the

wireless devices that you programmed into the Quik

Bridge Supervised One-Channel Receiver.

General procedure for testing the receiver:

CAUTION: To avoid sending false alarms to the

police or fire department when test-

ing monitored systems, always call

and notify the central station before

activating alarms.

1) For monitored systems, call the central station or

other monitoring service to let them know you

will be testing the system.

2) Arm the panel.

3) Trip a wireless sensor or other device that you

added to the receiver.

4) Restore the sensor to its non-alarm state and dis-

arm the system. Repeat steps 4 and 5 for each

wireless device. Verify that the system goes into

alarm (i.e., sirens activate).

5) If necessary, call the central station and let them

know you have finished testing the system.

Figure 7. Wiring a receiver zone to be N/O

Specifications

Dimensions: 2.5 ×2.6 ×0.9’’(64 ×66 ×23 cm)

Maximum current draw (both relays on): 70 mA

Operating temperature range: 40 to 120°F (4 to 49°C)

Power requirements: 11.5 to 15 VDC

Receiver frequency: 319.5 MHz

Receiver range: 250 feet (76 meters) minimum in

open air

Receiver type: Super regenerative

Relay contact rating:

Current: 7A maximum

Voltage: 250 VAC maximum

Contact: Dry contact Form C

Weight: 2.5 oz., including antenna

9216G 05a.D S F

PANEL

ZO N E

IN P U T S

SUPERVISE RELAY N/O

SUPER VISE RELAY CO M M O N

SUPERVISE RELAY N/C

ALARM RELAY N/O

ALARM RELAY CO M M ON

ALARM RELAY N/C

+12 V D C

GROUND

RECEIVER ZONE

OUTPUT TERM INALS

RETURN

ZO N E 1

+12 V D C

GROUND

RETURN

ZO N E 2

1 2 3 4 5 6 7 8

9216G 07a.D S F

PANEL

ZO N E

IN P U T S

SUPERVISE RELAY N/O

SUPER VISE RELAY CO M M O N

SUPERVISE RELAY N/C

ALARM RELAY N/O

ALARM RELAY CO M M ON

ALARM RELAY N/C

+12 V D C

GROUND

RECEIVER ZONE

OUTPUT TERM INALS

RETURN

ZO N E 1

+12 V D C

GROUND

RETURN

ZO N E 2

1 2 3 4 5 6 7 8

Page 8

Quik Bridge® Supervised One-Channel Receiver

Notices

This device complies with FCC Rules Part 15. Operation is subject to the following two

conditions:

1) This may not cause harmful iinterference.

2) This device must accept any interference that may be received, including interfer-

ence that may cause undesired operation.

Changes or modifications not expressly approved by Interactive Technologies, Inc. can

void the user’s authority to operate the equipment.

ITI and Quik Bridge are registered trademarks of Interactive Technologies, Inc.

651/777-2690

651/779-4890

Inhaltsverzeichnis

Andere ITI Empfänger Handbücher

ITI

ITI CS-4000 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung