IWILL DGL200 Bedienungsanleitung

EC Declaration of Conformity

Iwill Corp.

No. 10, Wu Chuan 3rd Rd.,

Hsin Chuang City, Taipei,

Taiwan, R.O.C.

Declare under sole responsibility that the

DGL200 motherboard

Meets the intent of Directive 89/336/ECC for Electromagnetic Compatibility. Compliance was

demonstrated to the following specifications as listed in the official Journal of the European

Communities:

EN 50081-1 Emissions:

EN 55022 Radiated, Class B

EN 55022 Conducted, Class B

EN 60555-2 Power Harmonics

EN 50082-1 Immunity:

IEC 801-2 Electrostatic Discharge

IEC 801-3 RF Radiate

IEC 801-4 Fast Transient

About This Manual

This manual will introduce to the user how this product is consisted. All useful information will be

described in later chapters. Keep this manual for your future upgrade or system re-configuration.

Chapter 0 Overview

The features and specifications of this motherboard

Chapter 1 Quick Installation

The quick reference for experienced users

Chapter 2 Hardware Installation

The detailed information on jumper setting, connection, and hardware installation

Chapter 3 System BIOS Setup

The detail information of the system BIOS setup options

Chapter 4 SCSI BIOS Setup

The detail information of the SCSI BIOS setup options

This manual contains information protected by copyright law. All rights are reserved. No any part

of this document may be used or reproduced in any forms or by any means, or stored in a database

or retrieval system without prior written permission from Iwill Corp.

This manual is subject to change without notice. (PMDBL1H12AE)

Trademark

Intel / Pentium are trademarks of Intel Corporation.

IWILL and IWILL logo are trademarks of IWILL Corp.

Sound Blaster is a registered trademark of Creative Technology Ltd.

Sound Blaster-LINK and SB-LINK are trademarks of Creative Technology Ltd.

And all other product names are trademarks and registered trademarks of their respective owners.

Warning

Most of the features of this product have passed strict verification and are subject to change at any

time without notice. If any malfunction occurs due to the future technical changes made by the

respective component manufacturers, Iwill assumes no responsibility or liability for it.

Content

CHAPTER 0.................................................................................................5

OVERVIEW.................................................................................................5

0.1 FEATURES ..............................................................................................5

0.2 ENVIRONMENT REQUIREMENTS...............................................................7

0.3 MOTHERBOARD COMPONENTS PLACEMENT.............................................8

0.4 BACK PANEL CONNECTORS................................................................... 11

0.5 FORM FACTOR......................................................................................12

CHAPTER 1...............................................................................................13

QUICK INSTALLATION..........................................................................13

CHAPTER 2...............................................................................................16

HARDWARE INSTALLATION ................................................................16

2.1 PREPARATION AND INSPECTION .............................................................16

2.2 UNPACK THE DGL200..........................................................................16

2.3 INSTALLATION PROCEDURES..................................................................17

CHAPTER 3...............................................................................................27

SYSTEM BIOS SETUP..............................................................................27

3.1 INTRODUCTION.....................................................................................27

3.2 MAIN MENU.........................................................................................29

3.3 STANDARD CMOS SETUP ...............................................................30

3.4 BIOS FEATURES SETUP...................................................................32

3.5 CHIPSET FEATURES SETUP ............................................................37

3.6 POWER MANEGEMENT SETUP......................................................39

3.7 PNP/ PCI CONFIGURATION .............................................................43

3.8 INTEGRATED PERIPHERALS ..........................................................44

3.9 LOAD SETUP DEFAULTS.................................................................47

3.10 IWILL SMART SETTING.................................................................47

3.11 SUPERVISOR / USER PASSWORD SETTING.................................48

3.12 IDE HDD AUTODETECTION..........................................................48

3.13 SAVE & EXIT SETUP.......................................................................48

3.14 EXIT WITHOUT SAVING................................................................48

CHAPTER 4...............................................................................................49

SCSI BIOS SETUP.....................................................................................49

4.1 INTRODUCTION.....................................................................................49

4.2 CONFIGURE/VIEW HOST ADAPTER SETTINGS ........................................49

4.3 SCSI DISK UTILITIES............................................................................53

Chapter 0

Overview

Thank you for purchasing Iwill DGL200 motherboard. This operation manual will instruct you how

to configure and install the system properly. It contains an overview about the engineering design

and features of this product. Also, this manual provides useful information for later on upgrade or

configuration change. Keep this for your future need.

YEAR 2000 issue

The IBM compatible PC utilizes a Motorola MC146818 compatible Real Time Clock (RTC) chip to

maintain the date and time. Unfortunately, the “century”is not manipulated by the RTC. It uses 8-

bit of information to report the year and can only hold the last two digits of a year in packed BCD

format. So 1997 is reported solely as 97. Since the RTC also contains non-volatile memory, IBM

specified a location in the memory to hold “century”information. By combining the century data

with the year data, software can obtain a full 4-digit year. When the Year 2000 occurs, the RTC

reports the year as ’00’and the “century”in RTC memory will contain ’19.’Combining the full 4-

digit year yields 1900, not 2000. Any applications which compares dates, or uses relative dates to

perform functions will see an incorrect dates.

Motherboards contain BIOS, which is one of the key ingredients to check for systems designed to

handle the year 2000. All motherboards currently shipped from Iwill contain BIOS capable of

handling the year 2000 date correctly. The BIOS contains a feature that checks the least two

significant digits of the year stored in the RTC during each BIOS request (INT 1Ah) to read the

date and, if less than `80', updates the century byte to `20'. This feature enables operating systems

and applications using the BIOS date/time services to reliably manipulate the year as a four-digit

value.

Be aware that the BIOS capability alone does not ensure that the system will handle the transition

correctly. Other system components such as the operating system and application software also

need to be able to handle the year 2000 date and recognize the date format from other pieces.

0.1 Features

0.1.1 Processor

Single or dual Pentium®

II Xeon processor support

Supports 100 MHz system bus speed

Supports 512KB,1MB or 2MB L2 cache.

Supports all published Pentium®

II Xeon processor voltages

S.E.C. (Single Edge Contact) cartridge Slot 2 connector

Easy-jumper to set the processor speed from 400 MHz to 500 MHz

0.1.2 Core Logic

Intel 82443GX PCI/A.G.P. controller

Integrated DRAM controller

Integrated PCI bus mastering controller

Integrated Accelerated Graphics Port (A.G.P.) bus controller

Intel 82371EB PCI/ISA/IDE Xcelerator (PIIX4E)

Multifunction PCI-to-ISA bridge (PCI Rev 2.1 compliant)

Integrated IDE controller with Ultra DMA/33 support

USB host interface with support for two USB ports

Enhanced DMA controller and standard Interrupt controller and Timer function

System Management Bus (SMB) with support for DIMM SPD

0.1.3 Main Memory

Four 168-pin DIMM (Dual In Line Memory Module) sockets

Supports up to 2 GB of 3.3 V Unbuffered SDRAM or Registered DIMM

64-bit data interface with ECC support

0.1.4 SCSI Subsystem

Adaptec AIC-7896 PCI Bus Master Dual Ultra2 SCSI Host Adapter

Providing two LVD/SE channels

Providing up to 80 MB/sec sustained throughput on LVD/SE channel (LVD devices only)

Providing two 68-pin connectors on LVD/SE channel and one 50-pin LVD/SE channel.

Supports maximum cable length up to 12 meters on LVD/SE channel (LVD devices only)

Supports burst data transfer on the PCI bus up to 133 MB/sec

0.1.5 Multi I/O

Winbond W83977EF super I/O controller

Supports two floppy disk drives (include 3 Mode drive) and / or QIC-80 tape drive

Supports one multi-mode parallel port

Supports two high speed 16550 FIFO serial ports

Integrated keyboard controller

Integrated PS/2 mouse controller

Support Keyboard-Power-On function

Support Power Fail Recovery

0.1.6 Expansion slots

one ISA slots

Five PCI slots

One A.G.P. slot

0.1.7 Form Factor

Compliance with ATX Version 2.01 specification

Supports ATX power supply connector

Supports the remote on/off switch

Physical dimensions: length: 274 mm / width: 305 mm

0.1.8 Manageability

Winbond W83782 System Hardware Monitor

Wake on LAN header for use with add-in network interface cards (NICs)

0.1.9 Other features

Award BIOS

Using Flash ROM to provide on-board-upgrade ability without changing components

Plug and Play compatible

Supports Advanced Power Management (APM)

Supports Creative SB-LINK to deliver Sound Blaster 16 compatibility

0.2 Environment Requirements

Temperature 0-55 degrees C (operating or storage)

5% to 95% non-condensing relative humidity

At least a 250 W power supply

The power supply must comply with the following recommendations found in the spec.:

The potential relation between 3.3 VDC and +5 VDC power rails

The current capability of the +5VSB line

ATX Power supply must comply with ATX spec. 2.01. ( 5VSB >= 1A)

0.3 Motherboard Components Placement

The following figure shows the location of the motherboard components.

PCIx

AGP

FAN1

IDE0

IDE1

WOL

LPT

P. SLOT2

S. SLOT2

USB

CPU 1st Cap 2nd Cap

400MHz 400 ON none

450MHz 450 ON none

500MHz 500 ON none

550MHz 550 ON none

JP5

JP1

PWR ON

JP3

LVD/SE CH-B

PWR

DIMM0~3

FDC

JP2

J43

FIRRX

CIRRX

VCC

IRRX

GND

IRTX

LID-ON

GND

5VSB

GND

+12V

SENSE

1--2: SCSI Enable

2--3: SCSI Disable

1--2:Normal

2--3:Clear CMOS

550

400

450

500

RS0

RS1

SB-LINK

GNT#

GND

REQ#

GND

SIRQ

1--2: Disable KB-ON

2--3: Enable KB-ON

KB ON

ATPWR

FAN1A

FAN3

FAN2,2A,4

LVD/SE CH-A

LVD/SE CH-B

ISA

Tmp1

Tmp2,3

JP11

JX2

JX1

RST ALED

SPKR

Cathode-

Anode+

Reset

GND

VCC Cathode-

Anode+

Buzz

GND

Keylock

GND

NC PLED

ACPI LED

Anode+ Cathode-

SLED

Cathode-

Anode+

JP10

Location ScreenPrinting Description

J3 P.Slot2 Primary processor Slot 2

J4 S.Slot2 Secondary processor Slot 2

J5--J8 DIMM0--3 168-pin DIMM Sockets

J11 AGP A.G.P. connector

J12--J16 PCI1--5 PCI expansion slots

J21 ISA ISA expansion slots

J25 CHA LVD/SE Wide SCSI connector for LVD or leagcy

devices (68-pin)

J26 CHB LVD/SE Wide SCSI connector for LVD or leagcy

devices (68-pin)

J27 CHB LVD/SE Narrow SCSI connector for leagcy devices (50-pin)

J28 IDE 0 Primary IDE connector

J29 IDE 1 Secondary IDE connector

J30 FDC Floppy drive connector

J31 S1 Serial 1 connector

J32 S2 Serial 2 connector

J33 LPT Parallel connector

J34 USB Two USB connectors

J35 MS PS/2 mouse connector

J35 KB PS/2 keyboard connector

J37/J38 PWR Standard ATX power connector

J39 FAN1 Processor fan header

J66 FAN1A Processor fan header

J40 FAN2 Processor fan header

J67 FAN2A Processor fan header

J41 FAN3 System fan header

J65 FAN4 System fan header

J68 FAN5 System fan header

J42 PWR ON Remote power on/off header

J43 J43 Front panel I/O header

ACPI LED (pins 1--2): ACPI LED header

ALED (pins 5--6): IDE LED header

SLED (pins 7--8): SCSI LED header

RST (pins 9--10): Reset Switch header

PLED (pins 11--13): Power LED header

KL (pins 14--15): Keylock switch header

SPKR (pins 17--20): Speaker header

J44 SB-LINK Creative SB-LINK header

J45 IR IR (infrared) connector

J46 WOL Wake On LAN header

J49 Tmp1 Temp. sensor header

J50 Tmp2 Temp. sensor header

J51 Tmp3 Temp. sensor header

J52 KB ON Jumper for Keyboard-Power-On

enable/disable

J64 ATPWR 3.3V PWR Connect

JP1 CLRTC Jumper for clearing CMOS

JP2 SCSI Jumper for SCSI enable/disable

JP3 JP3 Jumper for processor frequency selection

JP5 JP5 Jumper for PCI devices compatibility

JP10 JP10 Power on function for BIOS or hardware control select.

JP11 JP11 Chassis Intrusion

JX1 JX1 SMBUS Connect

JX2 JX2 Internal Modem Wake up connect.

Inhaltsverzeichnis

Andere IWILL Hauptplatine Handbücher

IWILL

IWILL P55TV Bedienungsanleitung

IWILL

IWILL mP4G2 Series Bedienungsanleitung

IWILL

IWILL KK266plus-R Original Betriebsanleitung

IWILL

IWILL DK8X Bedienungsanleitung

IWILL

IWILL DP533 Series Bedienungsanleitung

IWILL

IWILL DPX2-S320 Bedienungsanleitung

IWILL

IWILL Motherboard DJ800 Bedienungsanleitung

IWILL

IWILL UPX Bedienungsanleitung

IWILL

IWILL DP400 Bedienungsanleitung

IWILL

IWILL P4GB Series Bedienungsanleitung

IWILL

IWILL P4SE2 Bedienungsanleitung

IWILL

IWILL DVD266u-RN Bedienungsanleitung

IWILL

IWILL mp4s Original Betriebsanleitung

IWILL

IWILL DK8S Bedienungsanleitung

IWILL

IWILL PIINS Bedienungsanleitung

IWILL

IWILL DH800 Bedienungsanleitung

IWILL

IWILL DN800-SATA Bedienungsanleitung

IWILL

IWILL DX400-SN Bedienungsanleitung

IWILL

IWILL K7S3 Series Bedienungsanleitung

IWILL

IWILL KK266 Bedienungsanleitung

IWILL

IWILL DNS-SATA Bedienungsanleitung

IWILL

IWILL VD133 Bedienungsanleitung

IWILL

IWILL KD266 Bedienungsanleitung

IWILL

IWILL DN800-SLI Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung