JABSCO 36960-2 Series Bedienungsanleitung

Model 36960-2 Series

ELECTRIC BILGE PUMPS

FEATURES

•Self-Priming

•Diaphragm Design Allows Dry Running

•Built-in Hydraulic Pulsation Dampener

•Pumpgard®Strainer Included with Pump

•Corrosion Resistant Materials Throughout

for Sea Water Service

•Meets USCG Regulation 183.410 and

ISO 8846 MARINE for Ignition Protection

PRODUCT SPECIFICATIONS

Open Flow . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 GPM

Vertical Dry Suction Lift . . . . . . . . . . . 7 Feet (2.1 m)

Ports . . . . . . . . . . . . . . . . . . . . . . . . 3/4” Slip-on Hose

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 lb. (3.2 kg)

INSTALLATION

MOUNTING

Mount upright in a dry location (above highest bilge

water level) on a solid surface. Selection of a dry, cool,

ventilated location will generally extend pump life. Locate

Pumpgard strainer in accessible spot in suction hose.

PLUMBING

For intake and discharge use 3/4” ID non-collapsible

hose. Keep intake and discharge line free of kinks and

restrictions. To protect pump from debris, use the 3/4” in-line

strainer, Model 36200-0000 in the intake line from the bilge.

WIRING

Wire pump in a circuit independent of all other electrical

fixtures. Use stranded copper wire. Install fuse in posi-

tive circuit. See table for recommended wire and fuse

size. See diagram for wiring instructions. Use a 10 amp-

rated switch (44960-Series). After installation, it is rec-

ommended that voltage be checked at the motor termi-

nals with motor operating under full load. Voltage should

not be less than 90% of rated motor voitage.

STANDARD MODELS

Model Voltage Current Fuse Size

36960-2000 12 Vdc 6 Amp 8 Amp

36960-2010 24 Vdc 5 Amp 7 Amp

WINTER STORAGE

When possible it is preferred that the complete pump be

removed and stored in a warm dry place. If this is not

possible the pump must be completely drained, hoses

removed and pump run until all water is expelled.

WIRE SIZE TABLE

Model Model

Wire Length Between

36960-2000 36960-2010

Battery and Motor 12 Volt 24 Volt

1-25 ft. 12 AWG 14 AWG

26-50 ft. 10 AWG 14 AWG

6.31 (160)

7.50 (191)

7.31

(186)

4.75 (111)

DIMENSIONAL DRAWING

Inches (Millimeters)

BATTERY

MANUAL

AUTOMATIC

OFF

FUSE/

BREAKER PUMP

Automatic Bilge Switch

Model 34875-0000 or

Model 30295-1000

per instructions

3-Way Switch

44960-0000

WIRING DIAGRAM FOR

AUTOMATIC OPERATION

U.S.A.

Jabsco

Cape Ann Industrial Park

Gloucester, MA 01930

Tel: 978.281.0440

Fax: 978.283.2619

UNITED KINGDOM

Jabsco

Bingley Road, Hoddesdon

Hertfordsire EN11 OBU

Tel: +44 (0) 1992 450145

Fax: +44 (0) 1992 467132

CANADA

Fluid Products Canada

55 Royal Road

Guelph, Ontario N1H 1T1

Tel: (519) 821.1900

Fax: (519) 821.2569

JAPAN

NHK Jabsco Company Ltd.

3-21-10, Shin-Yokohama

Kohoku-Ku, Yokohama, 222

Tel: 045.475.8906

Fax: 045.475.8908

GERMANY

Jabsco GmbH

Oststrasse 28

22840 Norderstedt

Tel: +49-40-53 43 73 -0

Fax: +49-40-53 53 73 -11

THE PRODUCTS DESCRIBED HEREIN ARE SUBJECT TO THE

JABSCO ONE YEAR LIMITED WARRANTY, WHICH IS AVAILABLE

FOR YOUR INSPECTION UPON REQUEST.

Key Part No. Description Qty

130202-0000 Motor Kit 12 Vdc 1

130201-0010 Motor Kit 24 Vdc 1

235487-0000 Motor Mount 1

730040-0000 Connecting Rod Assembly* 1

835688-0000 Diaphragm Plate 2

930015-0000 Diaphragm* 1

10 35455-0000 Retainer 1

11 30003-0000 Valve Set (Inlet & Outlet)* ‡ 1 Set

12 44114-1000 Base Assembly ‡ 1

13 37175-0000 Ports (Inlet & Outlet) Barb ‡ 1 Set

14 44127-1000 Pulsation Dampener* 1

15 35686-0000 Bottom Plate ‡ 1

20 44990-0058 Vibration Pad Kit 1 Set

21 43990-0060 Hardware Kit 1 Set

43990-0063 Service Kit*

* Indicates parts contained in Service Kit

‡ Indicates parts supplied with Base Assembly

EXPLODED VIEW TROUBLESHOOTING

Problems Causas

Loss of suction to pump

•Air leak in suction line

•Bilge pickup not submerged

•Intake hose kinked or plugged

•

Fouled intake or discharge valve

•Ruptured diaphragm

Rough or noisy operation •

Intake or discharge hose

kinked or plugged

•Pump not mounted firmly

•Loosened eccentric set screw

or worn connecting rod assembly

•Ruptured or collapsed

pulsation dampener.

VALVE REPLACEMENT

1. Turn off power to pump. Remove four motor mount tie down bolts.

2. Expose valves by lifting motor mount and the attached

diaphragm assembly from pump base.

Remove valve retaining plate. Remove and clear or replace valves.

4. Install valves, making sure rubber flapper is UP on intake and

DOWN on discharge. Replace valve retaining plate.

5. Replace motor-mount-diaphragm assembly and fasten evenly

to base with the four tie down bolts.

DIAPHRAGM AND CONNECTING ROD

REPLACEMENT

Turn off power to pump. Remove four motor mount tie down boIts.

2. Lift motor mount and the attached diaphragm assembly from

pump base.

Remove two diaphragm retainer screws and the diaphragm retainer.

4. Pull connecting rod assembly and diaphragm from motor

mount, then, unscrew bolt to separate diaphragm plates.

5. Loosely reassemble new diaphragm, diaphragm plates, wash-

er and diaphragm boft onto new connecting rod assembly.

6. Slide connecting rod on shaft. Ensure that eccentric is firmly

seated on motor shaft and set screw firmly against flat side of shaft.

7. Tighten connecting rod bolt while maintaining alignment of rod

bearing eccentric. NOTICE. Avoid misalignment or twisting of

rod on eccentric shaft or excessive bearing wear will result.

PULSATION DAMPENER REPLACEMENT

1. Disconnect power leads from pump and remove from mount.

2. Remove nine bottom plate screws and the bottom plate. Pull

out and replace pulsation dampener

3. Replace bottom plate and screws. Tighten evenly to ensure an

air and water seal.

4. Reinstall pump and reconnect power leads.

MARINE SWITCH PANELS

BILGE PUMP

44960-0000

Lighted Switch

w/Boot SPST

BILGE PUMP

44960-0001

Unlighted

SPST

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JABSCO Wasserpumpe Handbücher

JABSCO

JABSCO 59510-Series Bedienungsanleitung

JABSCO

JABSCO 18690-0000 Bedienungsanleitung

JABSCO

JABSCO 30520-1 Series Bedienungsanleitung

JABSCO

JABSCO 52700 Bedienungsanleitung

JABSCO

JABSCO 30510-1003 Bedienungsanleitung

JABSCO

JABSCO 18670 Series Bedienungsanleitung

JABSCO

JABSCO 36600-0000 Bedienungsanleitung

JABSCO

JABSCO 30580 Series Bedienungsanleitung

JABSCO

JABSCO 17800 series Bedienungsanleitung

JABSCO

JABSCO 52520-1000 Bedienungsanleitung

JABSCO

JABSCO 50890 Bedienungsanleitung

JABSCO

JABSCO 30550-0 Series Bedienungsanleitung

JABSCO

JABSCO 30296 Series Bedienungsanleitung

JABSCO

JABSCO 37202-2712 Bedienungsanleitung

JABSCO

JABSCO 1285O SERIES Bedienungsanleitung

JABSCO

JABSCO 50870 Series Bedienungsanleitung

JABSCO

JABSCO 28 Series Bedienungsanleitung

JABSCO

JABSCO 30520-4 Series Bedienungsanleitung

JABSCO

JABSCO 30510-5 Series Bedienungsanleitung

JABSCO

JABSCO 18590 Series Bedienungsanleitung

JABSCO

JABSCO VR050-2022 Bedienungsanleitung

JABSCO

JABSCO 1673-Series Bedienungsanleitung

JABSCO

JABSCO 36680-2 Series Bedienungsanleitung

JABSCO

JABSCO 12490 Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung