JABSCO 1673-Series Bedienungsanleitung

Direct Drive – Clearance should be left between drive shaft

and pump shaft when installing coupling. Always mount and

align pump and drive shaft before tightening the coupling

set screw.

3. SPEEDS – 100 RPM to the maximum shown in the perfor-

mance table. Consult the factory for operation at speeds

above those shown. For longer pump life, operate at

lowest possible speeds.

4. SELF-PRIMING – Primes at low or high speeds. For

vertical lift of 10 feet (3.0mm), a minimum of 800 RPM

is required. Pump will produce suction lift of up to 22 feet

(6.7m) when wetted. BE SURE SUCTION LINES ARE

AIRTIGHT OR PUMP WILL NOT SELF-PRIME.

5. RUNNING DRY – Unit depends on liquid pumped for

lubrication. DO NOT RUN DRY for more than 30 seconds.

Lack of liquid will damage the impeller.

6. NOTICE – Do not pump light fraction petroleum derivatives,

solvents, thinners, highly concentrated or organic acids.

Damage to pump may result. Consult Jabsco Chemical

Resistance Table, available upon request from Jabsco,

for proper body materials and impeller compounds. If

corrosive fluids are handled, pump life will be prolonged if

pump is flushed with water after each use or after each

work day.

Model 1673-Series

SELF-PRIMING PUMPS

FEATURES

Body: Bronze

Impeller: Neoprene or Nitrile (Oil Resistant)

Shaft: Stainless Steel

Shaft Seal: Lip Seal, Buna N

Bearings: Sealed Ball Bearings

Ports: 1/2" NPT

Weight: 4-1/4 lb (2 kg) approx.

VARIATIONS AVAILABLE

Model 1673-Series

MODEL VARIATIONS

1673-1001 Neoprene Impeller

1673-1003 Nitrile Impeller (Oil Resistant)

1673-1051 Half Thickness Cam, (Where reduced

capacity is required with a fixed speed)

APPLICATIONS & OPERATING INSTRUCTIONS

MARINE: Engine cooling, Pumping bilges, Washdowns,

Circulating water in bait tanks, Utility dock side pump.

INDUSTRIAL: Circulating and transferring, Velocity-mixing,

Pumping machine tool coolants, Return spill, Sump

drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Ink,

Dyes, Alcohol, Various acids, Tanning liquors, Glycerine,

Brine, etc.

FARMING: Pumping water for stock, Pumping water from

shallow wells and cisterns, Pumping liquid ballast into

tractor tires.

PLUMBING AND HOME EMERGENCY USE: Pumping out

flooded basements, Cesspools, Sumps, Water heaters and

water closets, Drains and sinks, Draining fishponds and

pools.

1. INSTALLATION – Pump may be mounted in any

position. Intake and discharge ports are determined by

the direction of shaft rotation (refer to Dimensional

Drawing). Before installing, turn the pump shaft in the

direction of the operating rotation.

2. DRIVE – Belt or Direct with flexible coupling.

NOTICE: Do not press pulley or coupling on the

shaft without supporting the shaft at the opposite

end to prevent its movement into the impeller bore.

Belt Drive – Overtight belt load will reduce pump

bearing life.

OPERATING INSTRUCTIONS (Cont.)

7. PRESSURES - Consult Head Capacity Table for

recommended maximum for continuous operation. If

pressures exceed those shown, consult the factory.

8. TEMPERATURES - Neoprene 45°-180° F (7°-82° C),

Nitrile 50°-180° F (10°-82° C).

9. FREEZING WEATHER - Drain unit by loosening end

cover.The following anti-freeze compounds can be

used without any adverse effects to the neoprene impeller:

Atlas “Permaguard”, DuPont “Zerex” and “Telar”, Dow

Chemical “Dowguard” and Olin Mathison “Pyro

Permanent”. Most methyl alcohol (methanol) based

antifreeze can be used with neoprene. (DO NOT USE

PETROLEUM BASED ANTI-FREEZE COMPOUNDS

OR RUST INHIBITORS.)

10. SPARE PARTS - To avoid costly shut downs, keep a

JABSCO Service Kit on hand.

KEY DESCRIPTION PART NO. QTY

1 SCREW KIT (CAM & END COVER SCREWS)† 18753-0134 1

2 ENDCOVER 11836-0000 1

3 *O-RING 18753-0133 1

4 *IMPELLER 1

NEOPRENE 1210-0001

NITRILE 1210-0003

5 *SEAL 92700-0060 1

6 CAM 1

FULL THICKNESS 490-0001

HALF THICKNESS 2434-0000

7 SCREW, CAM SEE KEY1

8 BODY 18753-0128 1

9 RETAINING RING 18753-0131 1

10 SLINGER 3286-0000 1

11 BEARING 92600-0120 2

12 SHAFT 18753-0129 1

13 RETAINING RING 18753-0132 1

14 KEY 9215-0010 1

SERVICE KIT

NEOPRENE 90015-0001

NITRILE 90015-0003

PARTS LIST

* Parts supplied in Service Kit. Also included is an end cover gasket for older model pumps. Do not use gasket with O-ring end

cover seal.

† Screw Kit contains 7 each #10-32 x 3/8” pan. hd. mach. screws and 1 each #10-32 x 5/16”pan. hd. mach. screw.

The 5/16” screw is used only with a half thickness cam.

EXPLODED VIEW

DISASSEMBLY

1. Remove end cover screws, end cover and O-ring.

2. Remove impeller by grasping hub with water pump pliers.

3. Loosen cam screw and remove cam (clean off sealant).

4. Remove pulley or coupling and key from shaft.

5. Remove retaining ring which secures bearing shaft

assembly to pump body.

6. From impeller end of pump, press bearing and shaft

assembly out of bearing bore.Remove slinger from shaft.

7. From drive end of pump, press the seal out of the

seal bore.

8. It bearings or shaft need to be replaced, carefully

insert two equal size slot screwdrivers between bearings

180 apart. Simultaneously twist screwdrivers in

opposite directions to separate bearings. Continue to

push bearings off of shaft taking care not to

damage bearings or scratch shaft.

9. Remove snap ring that positions the bearings on the

shaft.

NOTE: Inspect all parts for wear or damage and

replace where necessary.

ASSEMBLY

1. Install bearing positioning snap ring on shaft.

2. Press bearings (one from each end of shaft) onto

shaft and against positioning snap ring. Slide slinger

onto impeller end of the shaft and position against

raised shoulder near bearings.

3. Press seal (with lip pointing toward impeller bore) into

seal bore in pump body. Ensure it is seated in bottom of

seal bore.Lubricate seal lip with a small amount of

grease.

4. Align impeller end of shaft with the seal and press

shaft/bearing assembly into the bearing bore (push

on bearing outer race). Install bearing retaining ring

in retaining ring groove With concave side facing out

toward drive end of shaft.

5. Apply a thin layer of sealant to screw threads and

top of cam and install in body. Secure with cam

screw.

6. Lubricate impeller bore with light coat of water pump

grease and start impeller into bore with a rotary

motion, until impeller screw engages slot in shaft,

then push into bore.

7. Install O-ring and end cover.Secure with end cover

screws.

4 7/16

(112.7)

3/16 X 3/16 X 3/4 KEY

1 1/8

(28.6)

.625

.624 DIA.

DRAINAGE

HOLES

3 3/8

(85.7)

3 13/16

(96.8)

11/16

(17.5)

1 5/16

(33.3)

3/16 (4.8)

ROTATION

DISCHARGE

DISCHARGE 4 1/8

(104.8)

2 1/16

(52.4)

1 15/16

(49.2)

1 1/2

(38.1)

1 7/8

(47.6)

(76.2)

3 3/4

(95.3)

1/2-14

NPT THD

2 PORTS

13/32 (20.6)

DIA. HOLE

2 PLACES

DIMENSIONAL DRAWING

Inches (Millimeters)

Note: Progressively longer life may be expected as operating pressures and speeds are reduced. Factory Application Engineering assistance suggested

for operation in light area and recommended for heavy shaded area Capacitor type motor recommended. Table shows approximate Head-Flow for new

pump in US gallons (and liters) per minute.

4.3 10 3.0 1/6 7.6 1/4 11.0 1/4 13.0 1/3 15.2 1/2 16.7 1/2 18.0 1/2 19.6 3/4

(29.7) (3) (11.3) (28.7) (41.6) (49.2) (57.5) (63.2) (68.1) (74.2)

8.7 20 1/8 1/6 6.4 1/4 10.0 1/4 11.5 1/3 13.7 1/2 15.4 1/2 17.0 1/2 18.8 3/4

(60.0) (6) (6.8) (24.2) (37.8) (43.5) (51.8) (58.3) (64.3) (71.1)

13.0 30 _ _ 4.8 1/4 8.5 1/3 10.0 1/2 12.0 1/2 13.6 3/4 15.3 3/4 17.5 3/4

(89.7) (9) (18.2) (32.2) (37.8) (45.4) (51.5) (57.9) (66.2)

17.3 40 _ _ 3.3 1/4 6.7 1/3 8.5 1/2 10.4 1/2 12.0 3/4 13.5 3/4 16.0 1

(119.4) (12) (12.5) (25.3) (32.2) (39.3) (45.4) (51.1) (60.5)

21.6 50 _ _ _ _ 5.0 1/2 6.7 1/2 8.5 3/4 10.0 3/4 11.8 3/4 14.5 1

(149.0) (15) (18.9) (25.3) (32.2) (37.8) (44.6) (54.9)

26.0 60 _ _ _ _ _ _ 5.0 1/2 7.0 3/4 8.3 3/4 10.0 3/4 13.0 1

(179.4) (18) (18.9) (26.5) (31,4) (37.8) (49.2)

30.3 70 _ _ _ _ _ _ _ _ _ _ 6.5 3/4 8.0 1 11.0 1

(209.1) (21) (24.6) (30.3) 41.6

TOTAL HEAD 500 RPM 1160 RPM 1750 RPM 2100 RPM 2450 RPM 2750 RPM 3000 RPM 3600 RPM

P.S.I. Ft. of GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

Water

(kPa) (metre)(L/min) (L/min) (L/min) (L/min) (L/min) (L/min) (L/min) (L/min)

4.3 10 2.2 1/6 5.8 1/4 9.5 1/4 11.5 1/3 13.3 1/2 15.0 1/2 16.0 1/2 18.2 3/4

(29.7) (3) (8.3) (21.9) (35.9) (43.5) (50.3) (56.8) (60.5) (68.9)

8.7 20 _ _ 4.3 1/4 7.6 1/3 9.4 1/3 11.4 1/2 13.0 1/2 14.4 1/2 17.0 3/4

(60.0) (6) (16.3) (28.7) (35.6) (43.1) (49.2) (54.5) (64.3)

13.0 30 _ _ 2.5 1/4 6.0 1/3 7.4 1/2 9.3 1/2 11.0 1/2 12.6 3/4 15.3 3/4

(89.7) (9) (9.4) (22.7) (28.0) (35.2) (41.6) (47.7) (57.9)

17.3 40 _ _ _ _ 4.2 1/2 5.6 1/2 7.5 1/2 9.2 3/4 10.8 3/4 13.6 1

(119.4) (12) (15.9) (21.2) (28.4) (34.8) (40.9) (51.5)

21.6 50 _ _ _ _ _ _ 3.9 1/2 5.7 3/4 7.2 3/4 9.0 3/4 11.7 1

(149.0) (15) (14.7) (21.6) (27.2) (34.0) (42.3)

26.0 60 _ _ _ _ _ _ _ _ _ _ 5.5 3/4 7.1 3/4 9.7 1

(179.4) (18) (20.8) (26.9) (36.7)

TOTAL HEAD 500 RPM 1160 RPM 1750 RPM 2100 RPM 2450 RPM 2750 RPM 3000 RPM 3600 RPM

P.S.I. Ft. of GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

Water

(kPa) (metre)(L/min) (L/min) (L/min) (L/min) (L/min) (L/min) (L/min) (L/min)

4.3 10 1.6 1/6 4.1 1/6 6.3 1/4 7.7 1/3 9.0 1/3 10.1 1/2 11.0 1/2 13.1 3/4

(29.7) (3) (6.1) (15.5) (23.8) (29.1) (34.0) (38.2) (41.6) (49.6)

8.7 20 1.2 1/6 3.6 1/6 5.8 1/4 7.0 1/3 8.4 1/2 9.5 1/2 10.2 1/2 12.3 3/4

(60.0) (6) (4.5) (13.6) (22.0) (26.5) (31.8) (35.9) (38.6) (46.5)

13.0 30 _ _ 3.1 1/6 5.0 1/3 6.2 1/3 7.6 1/2 8.6 1/2 9.4 3/4 11.3 3/4

(89.7) (9) (11.7) (18.9) (23.4) (28.7) (32.5) (35.6) (42.8)

17.3 40 _ _ 2.4 1/6 4.1 1/3 5.3 1/2 6.7 1/2 7.7 3/4 8.9 3/4 10.3 3/4

(119.4) (12) (9.1) (15.5) (20.0) (25.3) (29.1) (31.8) (39.0)

21.6 50 _ _ _ _ 3.1 1/3 4.2 1/2 5.7 1/2 6.7 3/4 7.4 3/4 9.2 3/4

(149.0) (15) (11.7) (15.9) (21.5) (25.3) (28.0) (34.8)

26.0 60 _ _ _ _ _ _ _ _ 4.5 1/2 5.6 3/4 6.3 3/4 8.1 3/4

(179.4) (18) (17.0) (21.2) (23.8) (30.6)

TOTAL HEAD 500 RPM 1160 RPM 1750 RPM 2100 RPM 2450 RPM 2750 RPM 3000 RPM 3600 RPM

P.S.I. Ft. of GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

Water

(kPa) (metre)(L/min) (L/min) (L/min) (L/min) (L/min) (L/min) (L/min) (L/min)

HEAD CAPACITY TABLES

1673-1001 NEOPRENE

1673-1003 NITRILE

1673-1051 HALFCAM NEOPRENE

THE PRODUCTS DESCRIBED HEREIN ARE

SUBJECT TO THE JABSCO ONEYEAR LIMITED

WARRANTY, WHICH IS AVAILABLE FOR YOUR

INSPECTION UPON REQUEST.

U.S.A.

Jabsco

20 Icon

Foothill Ranch, CA 92610-3000

Tel: 949.609.5106

Fax: 949.859.1254

UNITED KINGDOM

Jabsco

Bingley Road, Hoddesdon

Hertfordsire EN11 OBU

Tel: +44 (0) 1992 450145

Fax: +44 (0) 1992 467132

CANADA

Fluid Products Canada

55 Royal Road

Guelph, Ontario N1H 1T1

Tel: (519) 821.1900

Fax: (519) 821.2569

JAPAN

NHK Jabsco Company Ltd.

3-21-10, Shin-Yokohama

Kohoku-Ku, Yokohama, 222

Tel: 045.475.8906

Fax: 045.475.8908

GERMANY

Jabsco GmbH

Oststrasse 28

22840 Norderstedt

Tel: +49-40-53 43 73 -0

Fax: +49-40-53 53 73 -11

Dieses Handbuch passt für folgende Modelle

Andere JABSCO Wasserpumpe Handbücher

JABSCO

JABSCO 12490 Series Bedienungsanleitung

JABSCO

JABSCO 18590 Series Bedienungsanleitung

JABSCO

JABSCO 51510 Series Bedienungsanleitung

JABSCO

JABSCO 31295-0092 Bedienungsanleitung

JABSCO

JABSCO 30580 Series Bedienungsanleitung

JABSCO

JABSCO 30580-0 Series Bedienungsanleitung

JABSCO

JABSCO 36680-2 Series Bedienungsanleitung

JABSCO

JABSCO CENTRI PUPPY 18510-000 Series Bedienungsanleitung

JABSCO

JABSCO 30510-3 Series Bedienungsanleitung

JABSCO

JABSCO 5850-0001 Bedienungsanleitung

JABSCO

JABSCO 6400 Series Bedienungsanleitung

JABSCO

JABSCO 18330 Series Bedienungsanleitung

JABSCO

JABSCO VR050-2022 Bedienungsanleitung

JABSCO

JABSCO 18940-0010 Betriebsanleitung

JABSCO

JABSCO 37202-2712 Bedienungsanleitung

JABSCO

JABSCO 30520-5 Series Bedienungsanleitung

JABSCO

JABSCO 31295 Series Bedienungsanleitung

JABSCO

JABSCO 23920-9503 Bedienungsanleitung

JABSCO

JABSCO 36960-2 Series Bedienungsanleitung

JABSCO

JABSCO 11860 Series Bedienungsanleitung

JABSCO

JABSCO 2620 Series Bedienungsanleitung

JABSCO

JABSCO 52700 Bedienungsanleitung

JABSCO

JABSCO 51270 Series Bedienungsanleitung

JABSCO

JABSCO 31395-0092 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung