Jacuzzi J-SHA Handbuch

Whirlpool Bath

J-SHA™II

Installation / Operating Instructions

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING: RISKOFACCIDENTALINJURYORDROWNING; CHILDRENSHOULDNOTUSEHYDROMASSAGE

BATHTUB WITHOUT ADULT SUPERVISION.

WARNING : TO AVOID INJURY, EXERCISE CAUTION WHEN ENTERING OR EXITING THE HYDROMASSAGE

BATHTUB

WARNING: RISK OF ACCIDENTAL INJURY OR DROWNING; DO NOT USE HYDROMASSAGE BATHTUB

UNLESS ALL SUCTION GUARDS ARE INSTALLED TO PREVENT BODY AND HAIR ENTRAPMENT.

WARNING: KEEP BODY AND HAIR A MINIMUM OF 6" AWAY FROM SUCTION FITTING AT ALL TIMES WHEN

THEWHIRLPOOLSYSTEMISOPERATING. HAIRLONGERTHANSHOULDERLENGTHSHOULDBESECURED

CLOSE TO THE HEAD.

WARNING: RISK OF ELECTRICAL SHOCK; DO NOT PERMIT ELECTRICAL APPLIANCES (SUCH AS HAIR

DRYER, LAMP, TELEPHONE, RADIO OR TELEVISION) WITHIN 60" (1.5 M) OF THIS HYDROMASSAGE

BATHTUB.

WARNING: RISKOFACCIDENTALINJURYORDROWNING; DONOTUSEDRUGSORALCOHOLBEFOREOR

DURING THE USE OF HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER TO AVOID UNCONSCIOUS-

NESS AND POSSIBLE DROWNING.

WARNING: RISK OF FETAL INJURY; PREGNANT OR POSSIBLY PREGNANT WOMEN SHOULD CONSULT A

PHYSICIAN BEFORE USING A HYDROMASSAGE BATHTUB EQUIPPED WITH A HEATER.

WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; DO NOT USE A HYDROMASSAGE

BATHTUB EQUIPPED WITH A HEATER IMMEDIATELY FOLLOWING STRENUOUS EXERCISE.

CAUTION; TEST THE GROUND FAULT CIRCUIT INTERRUPTER PROTECTING THIS APPLIANCE PERIODI-

CALLY IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS.

WARNING: RISK OF HYPERTHERMIA AND POSSIBLE DROWNING; WATER TEMPERATURE IN EXCESS OF

100°F(38°C)MAYBEINJURIOUSTOYOURHEALTH. CHECKANDADJUSTWATERTEMPERATUREBEFORE

USE.

WARNING: RISK OF HYPERTHERMIA; PEOPLE USING MEDICATIONS AND/OR HAVING AN ADVERSE

MEDICAL HISTORY SHOULD CONSULT A PHYSICIAN BEFORE USING A HYRDOMASSAGE BATHTUB

EQUIPPED WITH A HEATER.

ANEQUIPMENTGROUNDINGTERMINALISPROVIDEDINTHEFIELDWIRINGCOMPARTMENT. TOREDUCE

THE RISK OF ELECTRICAL SHOCK, THIS TERMINAL MUST BE CONNECTED TO THE GROUNDING MEANS

PROVIDEDINTHEELECTRICALSUPPLYPANELWITHACONNECTOREQUIVALENTINSIZETOTHECIRCUIT

CONNECTORS SUPPLYING THIS EQUIPMENT.

Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electri-

cal installation according to codes are required for proper installation and user satisfaction. We recom-

mend that a licensed contractor perform the installation of all Jacuzzi Whirlpool Bath products. Our war-

ranty does not cover improper installation related problems.

PRECAUTIONS

Do not operate the whirlpool system unless the bath is filled with water to at least 2" above the highest jet.

Never drop or insert any object into any opening.

Do not use oil-based bath additives in your whirlpool bath.

When cleaning your bath, do not use abrasive substances which will damage the bath's surface.

To prevent discoloration of the acrylic finish, do not fill the bath with water in excess of 140°F (60°C).

The whirlpool system should be purged at least twice a month. For your convenience, we have developed a

plumbing system cleaner (Systems Clean™) specifically for whirlpool baths. For availability call 1-800-288-4002.

Use this unit only for its intended purpose as described in this manual. Do not use attachments not recommended

by the manufacturer.

This unit must be connected only to a supply circuit that is protected by a ground fault circuit interrupter (GFCI).

Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the

test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to

operate in this manner, there is a ground current flowing, indicating a possibility of an electric shock. Do not use this

unit. Disconnect the unit and have the problem corrected by a qualified electrician before using.

A pressure wire connector is provided on the exterior of the motor to permit connection of an No. 8AWG (8.4 mm)

solid copper bonding conductor between this unit and all other electric equipment and exposed metal in the vicinity,

as needed to comply with local requirements.

This unit should be installed by a licensed electrician and grounded.

For built-in and drop-in units, install to permit access for servicing.

Specifications _______________________________________________________________________ 1

Framing and Support _________________________________________________________________ 2

Rough-in Reference __________________________________________________________________ 2

Electrical and Service Access ___________________________________________________________ 3

Drain Information_____________________________________________________________________ 4

Plumbing and Water Supply ____________________________________________________________ 5

Water Level Sensor___________________________________________________________________ 6

Rapid Heat™Operation ________________________________________________________________ 6

Operation __________________________________________________________________________ 7-11

Maintenance ________________________________________________________________________ 12-13

Warranty ___________________________________________________________________________ 15-16

Contents

Important: Read complete instructions before beginning installation.

Eachwhirlpoolbatharrivesreadyfor installation, completely equipped with motor/pump assembly and plumbing and

fittings necessary for whirlpool operation. The drain/overflow kit must be installed on the bath.

Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been

made. Do not lift the bath by the plumbing at any time; handle by the shell or frame only.

Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the

finish, do not install the bath. Damage or defect to the finish claimed after the bath is installed is excluded from the

warranty. Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good

order to the carrier. Refer any claims for damage to the carrier. For definitions of warranty coverage and limitations,

refer to the warranty information.

All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to

installation, the bath must be filled to the overflow with water and operated to check for leaks that may have

resultedfromshippingdamageormishandling. JacuzziWhirlpoolBathisnotresponsibleforanydefectthatcould

have been discovered, repaired, or avoided by following this inspection and testing procedure.

Save These Instructions for Future Use.

Owner's Record

Date Purchased ____________________________________________________________

Purchased From ____________________________________________________________

Installed By ________________________________________________________________

Serial Number ___________________________

J-Sha II Owner's Manual

PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Specifications

36"

(914 mm)

71-3/4"

(1822 mm)

21-1/4"

(540 mm)

(51 mm)

18"

(456 mm)

9-7/16" (240 mm)

5-3/8"

TOP VIEW

SIDE VIEW

(137 mm)

DIMENSIONS

71-3/4" (1822 mm) L

36" ( 914 mm) W

21-1/4" ( 546 mm) H

BATH

ELECTRICAL

REQUIREMENTS

115 VAC 60 Hz.

20 Amp

Single Phase

(Must be GFCI

Protected)

PRODUCT

WEIGHT

125 lb

(57 kg)

MOTOR/PUMP

115 VAC

Single phase

60 Hz.

FLOOR

47 lb/sq. ft.

(229 kg/sq. m)

OPERATING

GALLONAGE

72 U.S. gal

(273 liters)

RAPIDHEAT

ELECTRICAL

REQUIREMENTS

115 VAC 60 Hz.

15 Amp

Single Phase

(Must be GFCI

Protected)

J-Sha II Owner's Manual

Framing and Support

The floor structure beneath the bath must be able to support a total weight of bath, water, and bather.

If the subfloor is level, no other preparation is necessary. You can proceed to install the bath. If the subfloor is

not level, you MUST level the entire surface prior to installing the bath. Use a floor leveling compound. Do not

use mortar, plaster or minimal expansion structural foam to set the bath as this will interfere with bath components

on the bottom of the bath. Both sides of a joint or splice of subfloor should be level to each other.

The rim of the bath is not designed to support weight. If finish material is to overlap or contact the bath, the added

weight must be fully self-supporting.

The protective film liner inside the bath is used to prevent damage to the finish from shoes, tools, etc.

during installation. Before installation, remove liner to inspect for any defects, reapply and do not re-

move until final cleanup.

TYPICAL INSTALLATIONS

FLUSH TO WALL SEMI-SUNKEN OPTIONAL TILE FLANGE KIT

TILE

1" X 4" (NOT FOR SUPPORT)

MORTAR OR

ADHESIVE

SUB-FLOOR

FINISHING

MATERIAL

BATH RIM

CEMENT BOARD

STUD

WALL

SILICONE

SEALANT

PLASTER

FILLER

FLANGE

MORTAR

1" X 4"

(NOT FOR SUPPORT)

SEALANT

TILE

MORTAR OR

ADHESIVE

FLASHING

NAIL OR

SCREW

SEALANT

FLASHING

1" X 4" (NOT FOR SUPPORT)

Rough-in Reference

The drain requires a cutout in the floor.

36"

(900 mm)

*71-3/4"

(*1822 mm)

457 mm

(18")

9-7/16"

(240 mm)

Add1/4” (6 mm) to this dimension when roughing-in for 3 wall niche.

For semi-sunken installations, floor cutout is 69-3/4" x 34" (1772 mm x 864 mm).

13" x 4"

DRAIN/OVERFLOW

CUTOUT

18"

(457 mm)

J-Sha II Owner's Manual

Electrical Connections

Two separate circuits are required for this unit:

1. Whirlpool bath controller.

2. Rapid Heat.

1. J-Sha II

Installa120VAC20AMPdedicatedcircuitprotectedby

a Ground Fault Circuit Interrupter (GFCI).

DANGER: RISK OF ELECTRIC SHOCK. Connect

only to a circuit protected by a Ground Fault Circuit

Interrupter.

2. Rapid Heat

Install a 120 VAC 15 AMP dedicated circuit with GFCI

protection. For operation, refer to the RapidHeat in-

structions.

DANGER: RISK OF ELECTRIC SHOCK. Connect

only to a circuit protected by a Ground Fault Circuit

Interrupter.

Service Access

For partially or fully sunken installations, allow for

service access as shown. It is the installer's responsi-

bility to provide sufficient service access. Provide

adequate ventilation to cool the motor and to supply

sufficient air for the jets.

ELECTRICAL

CONNECTION

PUSH TO RESET

OVER HEAT

PROTECTION

WARM

HOT

MIN.

HEATER"ON"

SEPERATE GFCI

PROTECTED

CIRCUITS

RAPID HEAT

CONTROL

BOX

PROVIDE SERVICE ACCESS TO

THE THREE SIDESAS SHOWN

In some cases, access may not have been provided

because of the design of the bath environment and

having full understanding that in this case, it may be

necessary to remove the unit for service.

If this is the case, diagnosing a problem may not be

possible without complete access to the plumbing sys-

tem. This would necessitate the removal of the unit.

Although this practice is not commonly implemented, it

is an acceptable method.

In some cases access may have been provided in Area

AbutserviceisrequiredinAreaBwhichrequirestheunit

to be pulled for service and reinstalled.

If service access has not been provided, it is the

home owners responsibility to remove the bath and

provide the required access, should a repair be-

come necessary.

MOTOR

AREA

SERVICE ACCESS

J-Sha II Owner's Manual

Drain Information

A drain/overflow assembly must be installed on the bath, water tested, and connected to the sanitary system of the

house. After opening the carton, inspect for damage. A solvent weld type drain is included and must be installed as

shown. The drain solenoid wiring plug must be connected to the control box prior to drain/overflow assembly. The

plugposition(DrainSolenid)is shownonthe controlbox. Itisrecommendedthatthetailpipe beinstalledon thedrain

beforethedrain/overflowisinstalledonthebath. Handtightenandthenuseawrenchtotightenuntilthetailpipedoes

notturn. Followtheinstallation instructionsprovidedwiththedrain/overflow kittoinstallthedrain/overflow assembly.

Note: the bath must be propped up due to the length of the tail pipe.

NOTE: Watertightinstallationof thedrainis theinstaller'sresponsibility. Drain leakage isexcluded from the

Jacuzzi Whirlpool Bath warranty of this product.

1-1/4" FLEXIBLE PIPE

SOLENOID WIRING

TO CONTROL BOX

1-1/2" RIGID PIPE

(NOT PROVIDED)

1-1/2" TO 1-1/4" BUSHING (2)

TO BACK JET

DRAIN HOSE

BACK JET MANIFOLD

DRAIN SOLENOID VALVE

SPRING

CLAMPS

60°

J-Sha II Owner's Manual

Water Supply

Consult local authorities for plumbing code requirements in your area.

IMPORTANT: Proper installation of the fill spout plumbing and compliance with local codes are the

responsibility of the installer. Jacuzzi Whirlpool Bath does not warrant connections of water supply fittings

andpiping,fill systems,ordrain/overflowsystems. Norisitresponsible fordamagetothebathwhichoccurs

during installation.

CAUTION: Anonflammableprotectivebarriermustbeplacedbetweensolderingworkandbathunittoprevent

damage to the bath.

21-1/2"

Plumbing

Pump, jets, and suction fittings for the whirlpool system are factory plumbed in a combination of metric and schedule

40PVCpiping. AllJacuzziWhirlpoolBathproductsarefactorytestedforproperoperationandwatertightconnections

prior to shipping.

Before securing the bath to the floor, a test should be made for possible water leaks. Fill the bath until the nozzles

on the back rest are covered. If leaks are detected, notify your Jacuzzi Whirlpool Bath Dealer. Do not install the unit.

BACK REST NOZZLES

J-Sha II Owner's Manual

WATER LEVEL SENSOR

The bath is equipped with a water level sensor. When the water level is below the sensor, the pump/motor can

not be activated. When the water goes above the level sensor, the pump/motor can then be activated. If the

water level drops below the level sensor, the pump/motor will shut off. To restart the pump/motor after the water

level goes above the level sensor, the ON/OFF button must be pressed.

WATER LEVEL SENSOR

RAPIDHEAT

Operation

Once the heater is installed and the whirlpool pump is operating, the heating function is totally automatic. The

heater will help maintain the temperature of the water in the bath.

Vacuum Switch

The heater is equipped with a preset vacuum switch which will not allow the heater to turn ON if the pump is not

running with water flowing through the whirlpool system.

High-Limit Switch

The heater includes an exclusive High-Limit switch. This safety circuit will not false trip from hot tap water. It will

only turn off the heater if the thermostat fails. To reset, press the button. If the high-limit trips frequently, contact

your dealer.

Andere Handbücher für J-SHA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Jacuzzi Whirlpool Handbücher

Jacuzzi

Jacuzzi era EU95 Bedienungsanleitung

Jacuzzi

Jacuzzi ProTech LCD Bedienungsanleitung

Jacuzzi

Jacuzzi SIGNA 5 Bedienungsanleitung

Jacuzzi

Jacuzzi VIRTUS Bedienungsanleitung

Jacuzzi

Jacuzzi Mito 5 Bedienungsanleitung

Jacuzzi

Jacuzzi Nova 5 Bedienungsanleitung

Jacuzzi

Jacuzzi Luxura 5 Bedienungsanleitung

Jacuzzi

Jacuzzi lodge M Bedienungsanleitung

Jacuzzi

Jacuzzi BELLAVISTA 5.5 Bedienungsanleitung

Jacuzzi

Jacuzzi Amiga T700-LH Bedienungsanleitung

Jacuzzi

Jacuzzi J - 480 Technisches Handbuch

Jacuzzi

Jacuzzi Capella BE60 Bedienungsanleitung

Jacuzzi

Jacuzzi Platinum Series Bedienungsanleitung

Jacuzzi

Jacuzzi 2005 ProTech LED Series Bedienungsanleitung

Jacuzzi

Jacuzzi oortable spa Bedienungsanleitung

Jacuzzi

Jacuzzi Cetra 532 Bedienungsanleitung

Jacuzzi

Jacuzzi Delos Bedienungsanleitung

Jacuzzi

Jacuzzi SALON Bedienungsanleitung

Jacuzzi

Jacuzzi Nova 5 Bedienungsanleitung

Jacuzzi

Jacuzzi era EU70 Bedienungsanleitung

Jacuzzi

Jacuzzi J-135 Bedienungsanleitung

Jacuzzi

Jacuzzi FUZION 7236 RH Bedienungsanleitung

Jacuzzi

Jacuzzi Unique Bedienungsanleitung

Jacuzzi

Jacuzzi J - 415 Bedienungsanleitung

Beliebte Whirlpool Handbücher anderer Marken

Bestway

Bestway Lay-Z-Spa 54189 Bedienungsanleitung

Morphy Richards

Morphy Richards Essentials PC4006 Bedienungsanleitung

Softub

Softub PRESTIGE Bedienungsanleitung

JNJ SPAS

JNJ SPAS SPA-318 Installationshandbuch

KIRAMI

KIRAMI Comfort Family Bedienungsanleitung

QCA Spa

QCA Spa VS501 PAK (VL260 TOPSIDE) Bedienungsanleitung

HoMedics

HoMedics FB-655HJ-GB Bedienungsanleitung

Everyday Hot Tubs

Everyday Hot Tubs 530 Bedienungsanleitung

anko

anko SS-601A Bedienungsanleitung

Pooli

Pooli OS030979B Bedienungsanleitung

ab Solares Smart Spa Bedienungsanleitung

CalderaSpas

CalderaSpas CalderaSpas Utopia Series Bedienungsanleitung

Outsunny

Outsunny 848-047V70 Bedienungsanleitung

Aquatic

Aquatic INFINITY 1 Bedienungsanleitung

Master Spas

Master Spas MP Force Bedienungsanleitung

Asteria

Asteria 5630 Bedienungsanleitung

Image

Image IMSB61610, IMSG61610 Bedienungsanleitung

ViSAGE

ViSAGE FM-588D Bedienungsanleitung