Jbc DI Bedienungsanleitung

Inhaltsverzeichnis

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

DI

1 TOOL

CONTROL UNIT

Reference Guide

www.jbctools.com

2

DI/1 TOOL CONTROL UNIT

DESOLDERING PUMP

MS-A

DESOLDERING STAND

DR-SA

CONTROL UNIT

DI-2A

Connectable tools: T210, T245, PA, HT, AP, DR and DS.

Connectable modules: MS, MV and MN.

CONTENTS

INSTALLATION / I.E.CONNECTION

Power Cord Socket

WORK

220

time

SLEEP

220

time

HIBERNATION

room

temperature

JBC stations intelligently manage the tool temperature:

Work mode: When the tool is used, pre-set work temperature is 350º C.

Sleep mode: When the tool is in the stand, the temperature goes down to 220º C.

Hibernation mode: After longer periods of inactivity (pre-set i.e 30 minutes), the power is cut off and

the tool cools down to room temperature.

The advantage of this heat management is lifespan increase which ensure low cost of ownership.

HEAT MANAGEMENT

DI

1 TOOL

CONTROL UNIT

Reference Guide

ORIGINAL PIN: 0105

Main menu

Station settings Counters

Tool settings

1 Reset settings

2

Station settings

3

Tool settings

4

Counters

1 Temp unit

Celsius

2

Maximum temp 400

0

C

3

Minimum temp 200

0

C

4

Nitrogen mode OFF

1

Plugged hours 0

2

Working hours 0

3

Sleep hours 0

4

Hibernation hours 0

1

Fix one temp -----

2

Temp levels set OFF

3

Sleep delay 0 min

5

Program version

5

Help text OFF

6

Beep ON

7

Change PIN

5

No tool hours 0

6 Sleep cycles

0

7 Desold cycles

0

4

Sleep temp 220

0

C

5

Hibernationdelay

3

0 min

6

Temp adjust O

O

C

Tool DR

Tool DR

Exit

Back Back

Back

3

WORKING

0

c

Tool

DR

Power 10%

350

220

Sleep

C

o

Decrease & move down Increase & move up

Tip temperature

% Instant power supplied to the tool

Working tool model

Status

Selected temperature

SELECT key 2 seconds

to enter Menu

SETTINGS

Selection

ENGLISH / WARRANTY

The JBC 2 years warranty, guarantees this equipment against all

manufacturing defects, covering the replacement of defective parts

and all necessary labour.

Warranty does not cover product wear due to use or mis-use.

In order for the warranty to be valid, equipment must be returned,

postage paid, to the dealer where it was purchased enclosing this,

fully ﬁlled in, sheet.

MORE INFORMATION

www.jbctools.com

SERIAL N`

STAMP OF DEALER

DATE OF PURCHASE

0008528/0210

TECHNICAL SPECIFICATIONS

- Temperature selection from 90 to 450°C (±5%).

- Power: 75W.

- Safety transformer, mains separator and double isolation, with temperature protection fuse.

- DI-2A 230V control unit. Input: 230V 50Hz. Output: 24V.

- DI-1A 120V control unit. Input: 120V 60Hz. Output: 24V.

- Total weight of unit: 2 Kg.

- Complies with CE standards on electrical safety, electromagnetic compatibility and ESD protected housing

“skin effect”.

- RoHS compliant.

- Equipotential connector and the tool tip are connected to station mains ground supply for ESD protection.

This product should not be

thrown in the garbage.