Jbc AL-2A Bedienungsanleitung

www.jbctools.com

English

Auto-Feed Soldering station

Ref. AL-A

www.jbctools.com

2 3

ww w.jb cto ols .co m

Packing List

The following items should be included:

Metal Brush .................... 1 unit

Ref. CL6217

Auto-Feed Iron ............. 1 unit

Ref. AL250-B

Stand ............................... 1 unit

Ref. AL-SD

Power Cord .................... 1 unit

Ref. 0009417 (100V/120V)

0009401 (230V)

Sponge ........................... 1 unit

Ref. S0354

Manual ............................ 1 unit

Ref. 0016966

Solder Reel Stand ....... 1 unit

Ref. 008745

Auto-Feed Soldering

station ............................. 1 unit

Ref. AL-1A (120V)

AL-2A (230V)

AL-9A (100V)

Tip Cleaner .................... 1 unit

Ref. CL9885

Allen Key 2,5mm .......... 1 unit

Ref. 0780493

Auto-Feed Soldering station

Ref. AL-A

Features

Stand

Ref. AL-SD

Power

Socket

Equipotential

connection

Pedal connection

(optional)

Auto-feed Iron

Ref. AL250-B

Fuse

Main switch

www.jbctools.com

4 5

1. Open dragging mechanism

2. Place the guide set and

tighten the screws

Guide Set

3. Take the solder wire from the reel until the guide tube start

4. Close the dragging mechanism

Guide Tube

Start

Reel Stand Assembly

Adjusting System Assembly

SOLDER WIRE

www.jbctools.com

6 7

5. Connect the handpiece to the station and switch it on. With the handpiece out of the stand, press

the WIRE LOAD key till the solder leaves by the end of the guide tube. Fast wire

dragging

Solder wire dragging button

A. Adjust the dragging strength

to allow the forwarding of the

solder wire and to avoid stall

and or clogging situations when

any cause arises

B. Tighten the dragging

mechanism

Clutch Regulation

Control Screen

There are 4 tool status:

USE (Use). The tool is ready to work.

STD (Stand). The tool is placed in the stand but still not in the sleep mode.

SLP (Sleep). The tool is in the sleep mode in the stand, its temperature has dropped till the sleep temperature.

OL. The power circuit is overheated. The power is temporarily not supplied.

TEMP. 230ºC USE

disc. L 10 S 11

Tool temperature Tool status

Length of

wire

Speed

Working method

www.jbctools.com

8 9

CONTINUE ON NEXT PAGE

Parameters Modification of the Tool and the Station

To enter into this mode, you must hold the SELECT key for 3 seconds.

www.jbctools.com

10 11

ø 0,4

ø 0,6

1,8x0,8

ø 0,8

4,8x1,5

1,2x0,7

3,2x1,5

ø 2,2

2,2 x 1

1,2x0,7

2,2x1

4,8x1,5

ø 2,2

ø 3,8

2,2x1

ø 1,7

ø 1

www.jbctools.com

8-10 mm

12 13

1. Loosen the cartridge screw to release it.

Place the new cartridge in the Auto-feed iron.

Alignment

Guide tube

Ref . 0002401 - Ø 0,9 - 1,1 mm

Changing cartridge

For a safe cartridge change, unplug the tool or turn the station off before following these guidelines:

2. Align the tip of the cartridge with the

solder Guide tube.

Important: It is essential to insert the

cartridge till the end for a good connection.

Use the mark as reference. Tighten the

cartridge screw.

3. You must leave a gap of 8-10 mm

between the tip and the end of the Guide

tube.

4. Loosen the guide screw.

Adjust the Guide tube and tighten

the screw.

Adjustable Stand

Adjust the tool holder angle to suit your work position. The AL250-B Auto-feed Iron works with C250 cartridge range. Find the model that best suits your

soldering needs in www.jbctools.com

Compatible Cartridges

C250-420 C250-401

C250-405

C250-402

C250-406

C250-403

C250-412C250-404 C250-418

C250-409 C250-410

C250-413C250-407 C250-408 C250-411 C250-414 C250-415

Note: All the cartridges shown are actual size.

www.jbctools.com

14 15

Accessories

Fume Extractor

Ref. F4468

Support

Ref. AL-IA

Optional Guide set

Ref. 0002399 - Ø 0.4 - 0.5 mm

0002402 - Ø 0.6 - 0.8 mm

0002843 - Ø 1.1 - 1.5 mm

0013915 - Ø 1.6 - 1.8 mm

Driver Gear

Ref. 0002863

*Only included in the Ø 1.1 - 1.5 / Ø 1.6 - 1.8

Guide set for a correct dragging of the solder

wire.

Improve thermal transfer by cleaning the tip after each solder joint.

Tip Cleaner

Brass Wool

Ref. CL6210

Splashguard

Non-slip base

Sponge

Ref. S0354

Wiper

Ref. CL0236

Very effective cleaning method.

It leaves a small layer of

solder on the tip to

prevent oxidation

between cleaning

and rewetting.

It prevents splashing of

solder particles when using

the brass wool.

No need to hold the base

while cleaning tips.

The least harmful cleaning method.

Keep the sponge damp with

distilled water when working to

avoid tip wear.

A temperature resistant receptacle lets the

operator remove excess solder by gently

tapping or wiping.

Tapping: Wiping:

Tap gently to remove

excess solder.

Use the slots to

remove remaining

particles.

Optional

Inox Wool

Ref. CL6205

Metal Brush

Ref. CL6220

Tip-Tinner

Ref. TT-A

Sand

Ref. CL6211

www.jbctools.com

16 17

Safety

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station is

turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

Before carrying out maintenance, always allow the equipment to cool.

- Clean the station screen with a glass cleaner

or a damp cloth. Clean

periodically

- Use a damp cloth to clean the casing and

the tool. Alcohol can only be used to clean

the metal parts.

- Periodically check that the metal parts of

the tool and stand are clean so that the

station can detect the tool status.

- Maintain tip surface clean and tinned prior

to storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat

transfer to the solder joint.

- Periodically check all cables and tubes.

Maintenance

1. Pull off the fuse holder and remove the

fuse. If necessary use a tool to lever it off.

2. Press the new fuse into the fuse holder

and replace it in the station.

- Replace a blown fuse as follows:

- Replace any defective or damaged pieces. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

www.jbctools.com

18 19

Exploded View

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere jbc Lötpistole Handbücher

Beliebte Lötpistole Handbücher anderer Marken

Bakon

Bakon 3200 Bedienungsanleitung

Proxxon

Proxxon Gaslotset MGS Bedienungsanleitung

HAKO

HAKO FX-8804 Bedienungsanleitung

SATA

SATA 02002A Bedienungsanleitung

Velleman

Velleman HRJA151 Bedienungsanleitung

Weller

Weller WSM 1 Bedienungsanleitung

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Montageanleitung

ersa

ersa i-CON 1V Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-100 Bedienungsanleitung

Weller

Weller WAD 101 Bedienungsanleitung

Weller

Weller WXD 2 Bedienungsanleitung

AlienTek

AlienTek T100 Bedienungsanleitung

Atten

Atten ATETOOL AT-689A Bedienungsanleitung

Surtek

Surtek 112554 Abmessungen und Installationsanleitung

Parkside

Parkside PLBS 30 A1 Bedienungsanleitung

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Bedienungsanleitung

Weller

Weller WX1 Bedienungsanleitung

multicomp pro

multicomp pro MP740893 Bedienungsanleitung

jbc AL-2A Bedienungsanleitung

Beliebte Lötpistole Handbücher anderer Marken