Jbc BT-2BQA Bedienungsanleitung

BT-2BQA

Soldering Station

INSTRUCTION MANUAL

Packing List

The following items are included:

Power Cord ................................................ 1 unit

Ref. 0023714 (230V)

Manual ........................................................................................................................................................ 1 unit

Ref. 0030004

Control Unit ............................................... 1 unit

Brass Wool ................................................. 1 unit

Ref. CL6210

General Purpose Handle ..................... 1 unit

Ref. T245-A

Soldering Station

Ref. BT1B010

www.jbctools.com

This manual corresponds to the following references:

BT-2BQA - 230V

Features Cable collector

Quick Tip Changer

Tip

Cleaning

System

Stand

Yellow LED

(SLEEP)

Green LED

(IN USE)

Dial

Main switch

Fuse

Power Socket Equipotential connection

T245

General Purpose Handle

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

CD-Q:

Changing Grips*

Hold the grip and pull the tab.

Use pliers if necessary.

Tabs

New Grip

Replace the soft foam grips easily using the slip-on tabs. Note: Choose the correct grip depending on

your handle model.

1. Inserting Tabs 2. Inserting Handle 3. Removing Tabs

The sealing plug prevents undesirable flux vapors or particles from entering inside the tool. Its usage

is highly recommended for intensive applications when soldering is exposed to FOD environments or

for applications where the soldering iron works close to vertical position.

Replacing Sealing Plugs

Note: Choose the correct sealing plug depending on your

handle model.

Before replacing the sealing plug, unplug the power

supply and make sure the device is not hot.

Note: The chamfered side has

to be positioned towards the

handle.

2. Mounting Position 3. Inserting Sealing Plug1. Removing Sealing Plug

Sealing

Plug

Handle

Push the sealing plug inside

the handle until the sealing

plug and handle edges are

aligned.

Enter, not deeper than 8mm,

a small shaft or screwdriver,

lift and pull the sealing plug.

Never use a cartridge to do

this operation.

Push the grip with the tabs

onto the handle.

Handles Green grips Blue grips Black grips

T210, T210P, T210N T8658 T3310 T3311

T245, T245G, T245P T6057 T1528 T1530

Handles Sealing Plug

T210 OB1000

T245, T470 OB2000

* not included, sold separately

Put the slide-on tabs into the

new grip.

Quick Tip Changer

Compatible cartridges

The BT stations work with C245 cartridges and T245/T470 handpieces or C210 cartridges with T210

handpieces. Find the model that best suits your soldering needs in www.jbctools.com

Save time and change cartridges safely without switching the station off.

1. Removing 2. Inserting 3. Fixing

Place the handpiece in the

extractor and pull to

remove the cartridge.

Place the handpiece on top

of the new cartridge and

press down slightly.

Use the holes for fixing the

cartridge* as follows:

A. For straight C210.

B. For curved C210.

C. For C245.

*Important

It is essential to insert the cartridges as far as the mark for a proper connection.

Mark

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

Operation

AC Console

The LEDs indicate the station’s different work-

ing modes.

1. Station without a tool connected: The

green IN USE light ﬂashes with the sequence

(- - -- --).

2. Tool out of the support: The green IN

USE light is permanently lit, indicating that the

soldering iron tip is at working temperature.

3. Tool in the support (sleep mode): The yel-

low SLEEP light is permanently lit. In order that

the tool goes into sleep mode, the tool must

be in its support and the programmed sleep

temperature must be less than the temp. on the

dial or the preﬁxed temperature.

4. Station with previously ﬁxed temperature.

(Only for users of the AC console).

Soldering iron out of support:

- If the dial is above the preﬁxed temperature,

the green IN USE light is lit the majority of the

time, switching off brieﬂy at regular intervals

(___ ___).

- If the dial is below the preﬁxed temperature,

the green IN USE light is off the majority of

the time, lighting up brieﬂy at regular intervals

(- - -).

- If the dial is at the preﬁxed temperature, the

green light is permanently lit.

Errors

When the handpiece or the cartridge is in an

open circuit, the green IN USE light ﬂashes with

the sequence (- - - - - -).

When the handpiece or the cartridge is in a

short circuit, the green IN USE light ﬂashes with

the sequence (--- --- ---).

If any of the above mentioned causes is corrected,

the station will start working automatically.

If the station is used continually in a overloaded

condition for a period of time, the system will

stop and both leds will ﬂash simultaniusly.

Switch station off and on to reset and review

the soldering application.

Yellow LED

(SLEEP)

Green LED (IN USE)

Dial

The original parameters of control unit can be

modiﬁed using the AC console.

It is necessary to connect the console AC with

software revision 7.0 or later to the BT in order to

conﬁgure it (consult JBC for console software updates).

Previous versions only allow for reading of

counters and do not allow for modiﬁcation of

parameters.

Conﬁguration possible:

- Fixing the working temperature.

- Selection of temperature units ºC or ºF.

- Modiﬁcation of sleep temperatures and standby

times.

- Adjustment of temperature.

- Reset the parameters back to factory settings.

- Read-out data:

- Working hours.

- Sleep cycles and sleep hours.

- Cartridge and iron changes.

- Program version.

Before carrying out maintenance, always allow the equipment to cool.

Clean

periodically

- Clean the station screen with a glass cleaner

or a damp cloth.

- Use a damp cloth to clean the casing and the

tool. Alcohol can only be used to clean the

metal parts.

- Periodically check that the metal parts of the

tool and stand are clean so that the station

can detect the tool status.

- Maintain tip surface clean and tinned prior to

storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat transfer

to the solder joint.

- Periodically check all cables and tubes.

- Replace a blown fuse as follows:

Maintenance

1. Pull off the fuse holder and remove the

fuse. If necessary use a tool to lever it off.

2. Press the new fuse into the fuse holder

and replace it in the station.

- Replace any defective or damaged pieces. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded before

use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station is

turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

Safety

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

Notes

40 mm

50 mm

60 mm

80 mm

100 mm

130 mm 130 mm

para manuales - color gris

200 mm

300 mm

Notes

Inhaltsverzeichnis

Andere jbc Lötpistole Handbücher

jbc

jbc MD 3050 Bedienungsanleitung

jbc

jbc HA245A-5B Bedienungsanleitung

jbc

jbc PA120-A Bedienungsanleitung

jbc

jbc BD Bedienungsanleitung

jbc

jbc PHSK-B Bedienungsanleitung

jbc

jbc CP-2E Bedienungsanleitung

jbc

jbc Premium DIR-D series Bedienungsanleitung

jbc

jbc CTS Bedienungsanleitung

jbc

jbc AD 2910 Bedienungsanleitung

jbc

jbc CS2R245-A Bedienungsanleitung

jbc

jbc HDRE-9A Bedienungsanleitung

jbc

jbc NP105-B Bedienungsanleitung

jbc

jbc Precision B-iRON Station Bedienungsanleitung

jbc

jbc CP-9QF Bedienungsanleitung

jbc

jbc CDS Bedienungsanleitung

jbc

jbc DIS-D Series Bedienungsanleitung

jbc

jbc CL8010 Bedienungsanleitung

jbc

jbc advanced Series Bedienungsanleitung

jbc

jbc KHT470A Bedienungsanleitung

jbc

jbc JTE-1B Bedienungsanleitung

jbc

jbc Premium DIT-D Series Bedienungsanleitung

jbc

jbc B-iRON 115 Bedienungsanleitung

jbc

jbc IN 2100 Bedienungsanleitung

jbc

jbc ALE Series Bedienungsanleitung

Beliebte Lötpistole Handbücher anderer Marken

Bakon

Bakon 3200 Bedienungsanleitung

Proxxon

Proxxon Gaslotset MGS Bedienungsanleitung

HAKO

HAKO FX-8804 Bedienungsanleitung

SATA

SATA 02002A Bedienungsanleitung

Velleman

Velleman HRJA151 Bedienungsanleitung

Weller

Weller WSM 1 Bedienungsanleitung

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Montageanleitung

ersa

ersa i-CON 1V Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-100 Bedienungsanleitung

Weller

Weller WAD 101 Bedienungsanleitung

Weller

Weller WXD 2 Bedienungsanleitung

AlienTek

AlienTek T100 Bedienungsanleitung

Atten

Atten ATETOOL AT-689A Bedienungsanleitung

Surtek

Surtek 112554 Abmessungen und Installationsanleitung

Parkside

Parkside PLBS 30 A1 Bedienungsanleitung

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Bedienungsanleitung

Weller

Weller WX1 Bedienungsanleitung

multicomp pro

multicomp pro MP740893 Bedienungsanleitung

jbc BT-2BQA Bedienungsanleitung

Beliebte Lötpistole Handbücher anderer Marken