jbc RHS-A Bedienungsanleitung
Rework Hand Support
Set for PHS
Ref. RHS-A
INSTRUCTION MANUAL
www.jbctools.com
Tool Arm ......................... 1 unit
Ref. HRR-A
Height adj. Knob........... 1 unit
Ref. 0023991
Shaft ........................ 1 unit
Packing List
The following items are included:
Base .............................................................. 1 unit Screw ........................................................... 1 unit
Ref. 0017057
Allen key ...................................................... 1 unit
Ref. 0013609
Manual ......................................................... 1 unit
Ref. 0023892
Ref. RHS-A
www.jbctools.com
INSTRUCTION MANUAL
Set for PHS
Rework Hand Support
2
Assembly
Fit the tool arm onto the base and tighten the
screw.
The tool arm position should be like the image
according with the letter back of the arm
support.
Setting up the Tool Arm
Height Adjustment
The RHS-A Arm allows adjustment for different
heights according to your work needs through
the vertical axis.
Slide the arm to the appropriate height and
secure by tightening the knob to guarantee
stability.
Knob
Maintenance
- Check periodically that the RHS-A is clean,
especially the sliding parts and the shaft.
- Use a damp cloth when cleaning. Alcohol
can only be used to clean the metal parts.
- Replace any defective damaged parts.
Use original JBC spare parts only.
Not leave up the RHS-A over the PH
when PH is working.
Keep the sliding
parts clean
www.jbctools.com
3
Work Position Adjustment
The RHS-A arm allows adjustment for different positions according to your work needs.
The articulated arm covers all work areas.
Position the arm and tighten the knobs.
Top view
See the work correct position of the hand in the following images.
4
Positioning PHS on RHS
Fit the positioning cap into
the positioning bolt.
The four corner guides helps
to the placement of the Unit.
Positioning Cap
Positioning Bolt.
It can be removed with a
screwdriver if fixed position is
not wanted.
The position of the PHS can be fixed on the RHS by means of positioning caps.
There are two possible PHS position.
www.jbctools.com
5
IR Preheater Support
Ref. PHS-SA
Ideal for working with JBC’s Hot Air stations and a Preheater, especially the PHS-KA.
Accessories
Rework Left Arm Support
Ref. HRL-A
Hot Air Heater Arm
Ref. 0024368
Shaft for Hot Air Heater Arm
Ref. 0024369
6
It is imperative to follow safety guidelines to prevent electric shock, injury,
fire or explosions.
Safety
- Do not use the equipment for any purpose other than PCB rework. Incorrect use may cause fire.
- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Not leave up the arms directly above heat surfaces.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight as well as persons with reduced
physical, sensory or mental capabilities or lacking experience provided that they have been given
adequate supervision or instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
www.jbctools.com
7
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life
must be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
Register your warranty within 30 days of purchase
in www.jbctools.com/productregistration
0023892-0120
Specifications
-Total weight: 5,6 kg (123.5 lb)
- Base dimensions: 270 x 410 mm (10.6 x 16.2 in)
- Height: 205 mm (8.1 in)
- Arm lenght: 498,1 mm (19.6 in)
- ESD safe connector
Complies with CE standards
ESD Safe
www.jbctools.com
Inhaltsverzeichnis
Andere jbc Werkzeuge Handbücher
jbc
jbc ALE250 Bedienungsanleitung
jbc
jbc CL0300 Bedienungsanleitung
jbc
jbc TEH Bedienungsanleitung
jbc
jbc AT420-A Bedienungsanleitung
jbc
jbc JTSE-1A Bedienungsanleitung
jbc
jbc PA120-B Bedienungsanleitung
jbc
jbc PA120-A Bedienungsanleitung
jbc
jbc AMS Bedienungsanleitung
jbc
jbc jbs-600 Bedienungsanleitung
jbc
jbc FAE020 Bedienungsanleitung
jbc
jbc ADVANCED MS 9000 Bedienungsanleitung
jbc
jbc PH207 Bedienungsanleitung
jbc
jbc NA101 Bedienungsanleitung
jbc
jbc CL2466 Bedienungsanleitung
jbc
jbc Advanced Series Bedienungsanleitung
jbc
jbc GAL0405 Bedienungsanleitung
jbc
jbc HT420 Bedienungsanleitung
jbc
jbc TM10 Bedienungsanleitung
jbc
jbc AT420 Bedienungsanleitung
jbc
jbc HRL Bedienungsanleitung
