JensPrima InnoCon 6501P Bedienungsanleitung

WALL MOUNTING

innoCon 6501

CAL

innoCon 6501 Monitor Manual

www.jensprima.com

Contents

Safety 2

............................................................

Product Introduction....................................................

Installation

.................................................................

...................................................

Display

Electrical Connection

...................................................................

Configuration Mode...................................................

Calibration Mode .......................................................

Maintenance

.........................................................

P010 Temperature parameter setting

.................................

Controller Installation.................................................

Sensor Installation

....................................................

P020 Relay 1 parameter setting

.......................................

pH Calibration

.......................................................

ORP Calibration

.....................................................

P030 Relay 1 parameter setting

......................................

P040 Current output parameter setting

P050 Offset parameter setting

P060 Measurement parameter selection

P070 Factory Reset

.......................................

..............................

...................................................

Page 1

innoCon 6501 Monitor Manual

Page 2www.jensprima.com

Safety

Legal requirements

Sensor

Signs

√ This manual introduces all the risks that may arise during the use of this equipment,

√ Please make sure this manual is delivered to the third party along with innoCon 6501.

Please use sensors manufactured by JENSPRIMA; Damages to the instruments caused

by the use of sensors not manufactured by JENSPRIMA within the warranty period will

not be covered by the warranty.

Only technicians authorized by jensprima can modify and update the instrument.

of corresponding regions and countries.

This sign is used to instruct the operator.

！

innoCon 6501

CAL

innoCon 6501 Monitor Manual

Product Introduction

General Information

The innoCon 6501P economical controller is designed for online monitoring of water

treatment and industrial process, matching with innoSens pH / ORP electrodes for

measuring pH / redox potential and temperature in water. Pt 1000 automatic

temperature compensation, installation methods of panel/pipe way, standard with

one line of 4-20mA output and two lines of relay output.

Applicaitons

Sewage / wastewater treatment, environmental monitoring, industrial processes,

swimming pools etc.

Supply

1. innoCon 6501P Controller

2. Fixed bracket

3. Operation Manual

4. innoSens pH/ORP Sensor (Need to purchase separately)

Features

√The latest wide power input, economical, 4-20mA output

√Teflon terminal, super anti-interference ability

√Large-screen backlit LCD shows measured values, temperature and relay status

√Password protection, to prevent unauthorized operation

√Pt 1000 automatic temperature compensation function

√IP65 protection class, a variety of installation methods

√2 lines of High/ Low relay output

√One key to restore factory settings

www.jensprima.com Page 3

innoCon 6501 Monitor Manual

www.jensprima.com Page 4

±0.2 C

Technical Parameters

Parameters

Measurement range

Resolution

pH ORP Temperature

-10.0~120.0 C

0~60.0C

-10~60.0 C

＞10 Ω

-2000~2000mV-2.00~16.00pH

0.01pH

±0.01pH ±1mV

Pt 1000

1mV 0.1 C

Accuracy

Temp.Compensation

method

Temp.compensation

range

Ambient Temp.

Storage Temp.

Resistance input

Display

Isolated 4-20mA output, can set pH/ORP, max.500Ω

90-260VAC,50/60Hz；24VDC optional

IP65

90 x 90mm

96 x 96 x 140mm

innoSens 120 pH Sensor

Applicable to pH measuremnet of the general

water treatment and high pollution wastewater

innoSens 210 ORP Sensor

Applicable to ORP measuremnet of the general

water treatment and high pollution wastewater

innoSens 125 pH Sensor

Applicable to pH measurement of high

temperature and high pollution wastewater

such as pulp, electroplating, desulfurization

wastewater

innoSens 130 pH Sensor

Applicable to pH measurement of high temperature

sterilization, high temperature fermentation etc.

innoSens 145 pH Sensor

Applicable to pH measurement of pure water,

RO water and other low range conductivity water

innoSens 150 pH Sensor

Applicable to pH measurement of hydrofluoric acid water

0.5Kg

2 sets of ON/OFF contacts, independent setting of High

/Low alarm point, with hysteresis function; 5A/250VAC;

5A/30VDC

English/Chinese

Panel/Pipe

Backlit super large lattice LCD

Analog output

Language

Power supply

Protection class

Alarm output

Installation method

Dimension

Panel cut size

Weight

innoCon 6501P Controller Parameters：

innoSens pH/ORP Electrode：

Please refer to the

relevant technical

documents to select

the appropriate

electrode.

innoCon 6501 Monitor Manual

www.jensprima.com

Installation

The instrument can be panel mounted and pipe mounted.

Make a hole of 90 x 90mm on the instrument case, put the instrument into the case

from the front of the panel of the case, insert screws from the back cover, and then

lock the fastening block to the fastening bar from the back of the panel.

Panel Mounting

Dimension

Pipe Mounting

Page 5

Cut Size Bracket Used for Panel Mounting

Bracket

90mm

U-tube from Pipe Mounting

innoCon 6501

CAL

96mm

140mm

Installation of Sensor

JENSPRIMA has many types of industrial electrodes that have a specific connection

function. The most common installation methods are: immersion type, pipe type,

flow type, tank installation and live bolt assembly type electrode tube installation.

Note:The above-mentioned connecting parts must be tightened to prevent water from damaging the electrodes

Protection Cover Components and Installation

innoCon 6501 Monitor Manual

www.jensprima.com Page 6

innoSens 120 pH Electrode

pH 0~14, -5~70℃

Controller: innoCon 6800 & innoCon 6501

Sensor: innoSens pH/ORP Sensor

Flange type

Side wall

welding seat

Pipe type

Immersion type

Bypass type

Round junction box upper cover

innoSens 120 pH Electrode

pH 0~14, -5~70℃

O ring

Electrode protection tube

Protection cover

Molded shell electrode（3/4”thread）

Recommend to wrap the thread with tape

Glass electrode

Rubber seat

Fixed bracket

Water-proof cable connector

Round junction box lower ring

innoCon 6501

CAL

innoCon 6501 Monitor Manual

www.jensprima.com

Electrical Connection

Central axis connected

with cable Connect 90-260VAC

Ntework cable

conntected with cable

Relay 1

Probe connected with

temperature Relay 2

4-20mA Output

The connectors of the controller are located behind the instrument cover,

only trained personnel can open the cover for wiring power, relay and signal

outputs. Use a screwdriver to unscrew the four screws on the back cover for

electrical connection.

Terminals

Page 7

Extension of electrical wire:

When opening the wire, make sure

to remove the black conductive rubber

cover outside the central axis.

Network

Cable

Central

Axis

mA-

mA+

Pt1000

4-20mA: Isolation Max. Load 600 ohm

Relay: 5A/250VAC 5A/30VDC

pH/ORP

Ref

Relay2

Relay1

90-260VAC

50/60Hz

！

90-260VAC

50/60Hz

！Relay1

Relay2

Pt1000

pH/ORP

Ref

mA-

mA+

Danger:

Electrical connections must be

carried out by technicians who

got special trainings.

Note:

Power supply must be cut off

prior to any connection, otherwise

the instrument and the sensor are

likely to be damaged.

innoCon 6501 Monitor Manual

www.jensprima.com

Display

Front View of the Controller

Relay Indicate

Unit

Temperature

Secondary display area

Main

display

area

Calibration

ATC -- Temperature

compensation mode

ATC ( Auto)/MTC (Manual )

Button Functions：

Menu/Back

Key

Calibration

Key

Enter

Key

Arrows

Key

Under measurement interface, press and

hold this button for 3 seconds to enter the

setup menu and return to the previous menu.

Under measurement interface, press and

hold this button for 3 seconds to enter the

calibration menu

Accept input value or selected menu

Under measurement interface, press this key

Press this button to switch the display backlight

Browse menus, change settings, and input

value,under measurement interface

Press this button to switch measurement

value and current

Enter the setting mode with password 0011.

Any time press can exit the calibration mode or go back to the previous

menu. Press same key to the measuring mode.

Page 8

Current Indicate

innoCon 6501

CAL

Inhaltsverzeichnis

Andere JensPrima Messgerät Handbücher

JensPrima

JensPrima innoCon 6800O Bedienungsanleitung

JensPrima

JensPrima innoCon 6800D Bedienungsanleitung

JensPrima

JensPrima innoCon 6800P Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung

JensPrima innoCon 6501P Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken