JL Audio Stealthbox SB-POL-RZG2SPKR/MX650 Bedienungsanleitung

Enclosure Type: Sealed

Driver Type: MX650-CCX-SG-TLD-B

Nominal Impedance: 4 ohms

Continuous Power Handling: 60 watts (RMS method)

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely

vital that the Stealthbox®be properly mounted to the vehicle

according to these instructions. Failure to mount the enclosure

properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a

collision or sudden deceleration.

INSTALLATION

DIFFICULTY:

ESTIMATED TIME:

12 HOURS

Continued on Next Page

OUT

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

INSTALLATION GUIDE

for the

SB-POL-RZG2SPKR/MX650

SKU# 94655

2014 & Up Polaris RZR XP 1000, RZR XP 4 1000

RZR 900 XC, & RZR 4 900

INCLUDED HARDWARE / WIRING INFORMATION

Continued on Next Page

Page 2 • JL Audio, Inc., 2017

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

Note: For optimum performance, JL Audio recommends applying the included Foam Strips (or sound damping material) to surrounding plastic panels to reduce unwanted vibrations.

(hardware pictured for one)

Wire Size Wire Color Use

16 AWG Red/Stripe Speaker Positive (+)

Black/Stripe Speaker Negative (-)

20 AWG

Red Not Used

Green Not Used

Blue LED Positive (+)

Yellow LED Negative (-)

* Pre-installed on enclosure

BOM ID Qty SKU Description

1* 2 152414 Wire Harness (10’)

2 2 153820 1/4 - 20 x 1” Stainless Steel Hex Cap Screw

3 2 153818 1/4” Stainless Steel Flat Washer

4 2 153817 1/4” Stainless Steel x 1” OD Flat Washer

5 2 153819 1/4” Stainless Steel Split Lock Washer

6 2 153816 1/4 - 20 Stainless Steel Hex Nut

- 2 101734 15” x 18” Pre-Cut Batting (not shown)

- 1 150778 Fuse & Fuse Holder Kit (not shown)

- 1 150249 Foam Tape (not shown)

LED Wire Connections

• For short-circuit protection, install a supplied fuseholder onto EACH

speaker’s BLUE (+12V) LED power connection lead.

• Connect all BLUE (+12V) leads together (parallel) and connect to a

switched +12V supply. Connect all YELLOW (GRD) leads together and

connect to a negative ground or to the NEGATIVE battery post.

• We recommend activating the speakers’ LEDs thru a lighting circuit that

supplies +12V via an existing switch. If an existing switched circuit is

not available, you may install a dedicated toggle/rocker style switch that

will supply positive (+12V) power. Fuse this connection according to how

many LED circuits you have (LED circuits x 150A).

[GND]

LED

[+12V]

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

LED

Fuse

[GND]

[+12V]

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

Blue

Yellow

LED

Fuse

Diagram shows one speaker pair of

LED circuits connected in parallel.

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio MX280/4. The diagram below shows the recommended crossover settings for the MX280/4. For a detailed description of the ampli-

er settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your

Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for

both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.

Continued on Next Page

Page 3 • JL Audio, Inc., 2017

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

Page 4 • JL Audio, Inc., 2017 Continued on Next Page

STEP 8

Slide a 1/4” Flat Washer over a 1/4 - 20 x 1” Hex

Cap Screw, and pass the assembly through the

hole drilled in the previous step, as shown.

STEP 7

Using a 1/4” drill bit, carefully drill through the

upper hole in the enclosure, through the

plastic panel, to the exterior wheel well area.

STEP 6

Pass the cable exiting the enclosure through

the hole in the plastic panel. Position the

speaker enclosure flush against the kick panel,

allowing the grommet to sit in the drilled hole.

Secure the enclosure using a factory bolt

through the lower hole in the enclosure, as

shown.

STEP 5

Using a 1-1/8” hole saw, enlarge the hole drilled

in the previous step.

STEP 4

Using a 1/8” drill bit, carefully drill through the

indicated mark on the Template, through the

plastic panel, to the exterior wheel well area.

Remove the factory bolts, and remove the

Template.

STEP 3

Cut the Template from Page 7 of this manual.

Align the lower holes in the Template to the

factory holes in the vehicle, and secure using

the factory bolts removed in the previous step.

The bottom of the Template should be parallel

with the horizontal edge of the plastic panel,

as shown.

STEP 2

Remove the two indicated factory bolts.

STEP 1

The following steps show the installation

procedure for the driver’s side only, but the

procedure is the same for both sides.

Empty the driver’s side of the vehicle.

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

Page 5 • JL Audio, Inc., 2017

RECOMMENDED SUBWOOFER SOLUTIONS

The SB-POL-RZG2/10TW3 and SB-POL-RZG2R/10TW3 Stealthbox® subwoofer enclosures are also available

for your vehicle. The weatherproof enclosures are designed for a perfect t and house a premium JL Audio

subwoofer.

SB-POL-RZG2/10TW3 SB-POL-RZG2R/10TW3

SKU# 94620 SKU# 94631

All specifications are subject to change without notice. “JL Audio®”and the JL Audio logo, “Stealthbox®”and the Stealthbox logo, and “How we play®” are registered trademarks of JL Audio, Inc.

“Ahead of the Curve” and its respective logo are trademarks of JL Audio, Inc.

(954) 443-1100

www.jlaudio.com

JLA-SKU# 011497 • ver. 09.26.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

STEP 10

Route the cable as necessary. Refer to Page 2

for wiring information.

STEP 9

From the exterior wheel well area, slide a 1/4” x

1” OD Flat Washer, a 1/4” Split Lock Washer, and

a 1/4 - 20 Hex Nut over the 1/4 - 20 x 1” Hex

Cap Screw, and fully tighten.

STEP 12

Connect and install the speaker. Remove the

adhesive backing, and install the JL Audio logo

badge.

Repeat the process for the passenger side.

Note: For optimum performance, we

recommend applying the included Foam Strips

(or sound damping material) to surrounding

plastic panels to reduce unwanted vibrations.

STE P 11

Reinstall the indicated factory bolt.

Place a 15” x 18” Pre-Cut Batting inside the

enclosure.

Page 6 • JL Audio, Inc., 2017

This page is intentionally left blank.

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

Page 7 • JL Audio, Inc., 2017

TEMPLATES

Carefully cut out the templates along the indicated lines.

SB-POL-RZG2SPKR/MX650 INSTR_SKU# 011497

DRIVER SIDE TEMPLATE

PASSENGER SIDE TEMPLATE

Andere JL Audio Autolautsprecher Handbücher

JL Audio

JL Audio C2-650x Bedienungsanleitung

JL Audio

JL Audio ZR570-CSi Bedienungsanleitung

JL Audio

JL Audio M770-CCS Bedienungsanleitung

JL Audio

JL Audio C3-100ct Bedienungsanleitung

JL Audio

JL Audio C2-350x Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 Bedienungsanleitung

JL Audio

JL Audio C5-570X Bedienungsanleitung

JL Audio

JL Audio Stealthbox 94376 Bedienungsanleitung

JL Audio

JL Audio TR650-CSi Bedienungsanleitung

JL Audio

JL Audio SB-F-Edg Bedienungsanleitung

JL Audio

JL Audio Evolution C5-650 Bedienungsanleitung

JL Audio

JL Audio C2-690tx Bedienungsanleitung

JL Audio

JL Audio Evolution C5-570x Bedienungsanleitung

JL Audio

JL Audio XR525-CXi Bedienungsanleitung

JL Audio

JL Audio 94607 Bedienungsanleitung

JL Audio

JL Audio C5-650x Bedienungsanleitung

JL Audio

JL Audio VR525-CSi Bedienungsanleitung

JL Audio

JL Audio XR650-CSi Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-AVAL/12W3v3 Bedienungsanleitung

JL Audio

JL Audio C2-525x Bedienungsanleitung

JL Audio

JL Audio VR650-CSi Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-F-EDG2G/10TW1 Bedienungsanleitung

JL Audio

JL Audio XR653-CS Bedienungsanleitung

JL Audio

JL Audio XR570-CSi Bedienungsanleitung

Beliebte Autolautsprecher Handbücher anderer Marken

Blaupunkt

Blaupunkt GTt 300 Technisches Datenblatt

Boston Acoustics

Boston Acoustics SX55 Bedienungsanleitung

Kenwood

Kenwood KFC-W212 Bedienungsanleitung

VR3

VR3 Elite VRS653 Bedienungsanleitung

Premier

Premier TS-W3001D4 Bedienungsanleitung

Infinity

Infinity 6530cx Bedienungsanleitung

Focal

Focal K2 Power 165 KRX3 Bedienungsanleitung

Precision Power

Precision Power PPI4.2 Bedienungsanleitung

Jensen

Jensen XS Series Bedienungsanleitung

Blaupunkt

Blaupunkt GTx Series Bedienungsanleitung

AudioBahn

AudioBahn AT60 Bedienungsanleitung

Focal

Focal BombA 27 V1 Bedienungsanleitung

Blueant

Blueant S1 Bedienungsanleitung

Naxa

Naxa NCS-768 Bedienungsanleitung

Focal

Focal Polyglass 130 VRS Bedienungsanleitung

Boston Mobile Audio

Boston Mobile Audio SR80 Bedienungsanleitung

Blaupunkt

Blaupunkt GTx 352 DE Bedienungsanleitung

Focal

Focal K2 POWER 130 KF Bedienungsanleitung