JL Audio Stealthbox SB-GM-CLREXT/10W3v2 Bedienungsanleitung

➔

Stealthbox®

INSTALLATION GUIDE

SB-GM-CLREXT/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011195 Revision 5/19/2005Page 1

for the

SB-GM-CLREXT/10W3v2

(2004-Up Chevrolet Colorado &

GMC Canyon Extended Cab)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation.Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1)The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JLAudio Stealthbox

responsibly.

STEP 1:

Remove all contents from rear of

truck.

STEP 2:

Remove the plastic jack cover and

jack from the bracket.

STEP 3:

Remove the (1) tire stops and with

a 10mm socket,(2&3)unbolt the jack bracket.

STEP 4:

Unbolt the bracket that is already

attached to the Stealthbox.

Set mounting hardware to the side.This will

be used in later steps.

STEP 5:

With the supplied hardware, attach

the bracket to the rear wall.

Place a 1/4”lock wash and a 1/4” flat washer

onto each #6x30mm-1mm bolt.

Place the bolts through the bracket and slide

one 1”Lx1”ODx3/8”ID spacer onto each bolt.

Line up the bolts to the factory threads and

secure tightly.

STEP 6:

Attach speaker wire to the

Stealthbox terminal and check the woofer for

proper operation.

START

HERE

Continued on Next Page ➔

www.jlaudio.com

➔

➔➔

STEP 7: With the hardware from STEP 4.

From under neath, attach the Stealthbox to the

bracket.

Secure tightly using an open end wrench.

STEP10: *CAUTION*

Before drilling, make sure that you are not going to be

drilling into any gas lines, brake lines, transmission lines,

electrical wiring, transfer case(4x4 vehicles) or any-

thing else that might cause a reduction in your weekly

pay.Always wear eye protection when drilling.

With the use of a 1/2” drill bit and drill. Drill out the

jack bracket and floor. Use the hole of the jack brack-

et as the drilling guide, as pictured.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: With the supplied hardware, attach the

jack bracket to the front of the Stealthbox.

VEHICLE SHEET METAL

FENDER WASHER

LOCK WASHER

Tap Bolt

FLAT WASHER

HEX NUT

FLAT WASHER

STEP 11: Attache the jack bracket to the floor,

using the supplied hardware.

Place a 3/8” lock washer and 3/8’flat washer onto

the 3/8”-16 x 2 bolt.

From inside the truck, slide the bolt through the

hole of the jack bracket and floor.

From under the truck, place the 3/8”fender washer,

3/8” flat washer and 3/8”-16 nut onto the protrud-

ing bolt.

Secure tightly.

➔

STEP 12: On the back side of the plastic jack

cover,there are two plastic guides.

Grind these guides off.

The picture above shows the guides already ground

off.

STEP 9: From under the truck, remove the heat

shield.

SB-GM-CLREXT/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011195 Revision 5/19/2005Page 2

www.jlaudio.com

➔

Specifications:

Enclosure Type: Sealed

Driver Type: 10W3v2-D2

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended

crossover,infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Included Hardware:

4) 1/4” FlatWasher

4) 1/4” Split LockWasher

2) 1/4”-20 x 1” Bolts

2) #6 x 30mm-1mm Hex Bolts

1) 3/8” Split LockWasher

2) 3/8” FlatWasher

1) 3/8” FenderWasher

1) 3/8”-16 x 2”Tap Bolt

1) 3/8”-16 Hex Nut

3) 3/4”Lx3/4”ODx3/8”ID Spacers

2) 1”L x1”OD x3/8”ID Spacers

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.

Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JLAudio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔➔➔

STEP 13: Place a supplied 3/4”Lx3/4”ODx3/8”ID

spacer onto the thumb screw.

Insert the thumb screw through the front of the

plastic jack cover.

STEP 14: On the back side of the plastic jack

cover.

Place the remaining pair of 3/4”Lx3/4”OD,3/8”ID

spacers onto the thumb screw.

STEP 15: Place the tire stops and jack back onto

the jack bracket.

Place the plastic jack cover over the jack assembly

and secure with the thumb screw.

➔

SB-GM-CLREXT/10W3v2, JL AUDIO, Inc 2005 Sheet SKU#011195 Revision 5/19/2005Page 3

www.jlaudio.com

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

XR650-CSi

TR650-CXi

Front Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR,XR & ZR650-CSi

Rear Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VT & XR650-CXi

Cont.

From

Page

Difficulty Of Installation:

Dieses Handbuch passt für folgende Modelle

Andere JL Audio Subwoofer Handbücher

JL Audio

JL Audio 12W1v3-2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-T-4RNR2/10W3v2 Bedienungsanleitung

JL Audio

JL Audio 13TW5v2-2 Bedienungsanleitung

JL Audio

JL Audio M8IB5 Bedienungsanleitung

JL Audio

JL Audio 12W5-D4 Bedienungsanleitung

JL Audio

JL Audio 94643 Bedienungsanleitung

JL Audio

JL Audio 15W3 18W3 Bedienungsanleitung

JL Audio

JL Audio MX101B3-SG Bedienungsanleitung

JL Audio

JL Audio 10TW3 Bedienungsanleitung

JL Audio

JL Audio 94592 Bedienungsanleitung

JL Audio

JL Audio 10W0 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-MIN-COOP/8W7 Bedienungsanleitung

JL Audio

JL Audio Stealtbox SB-K-SL-12W0v2 Bedienungsanleitung

JL Audio

JL Audio 13TW5-3 Bedienungsanleitung

JL Audio

JL Audio 12TW3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK Bedienungsanleitung

JL Audio

JL Audio M3-10IB Bedienungsanleitung

JL Audio

JL Audio 8W1v3-4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-T-4RNR/10W Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CLDRO/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-M-3-SPD/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-ESC/10W1v2 Bedienungsanleitung

JL Audio

JL Audio 15W1-4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-P-987C/13TW5v2 Bedienungs- und Wartungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung