JLG 1532E3 Gebrauchs- und Pflegehandbuch

Operation and Safety Manual

Models

1532E3

1932E3

2033E3

2046E3

2646E3

2658E3

3120877

July 23, 2012

FOREWORD

3120877 – JLG Sizzor – a

FOREWORD

DANGER INDICATES AN IMMINENTLY HAZARDOUS SITUATION

WHICH, IF NOT AVOIDED WILL RESULT IN SERIOUS INJURY OR

DEATH.]

CAUTION INDICATES A POTENTIALLY HAZARDOUS SITUATION

WHICH, IF NOT AVOIDED, MAY RESULT IN MINOR OR MODERATE

INJURY. IT MAY ALSO BE USED TO ALERT AGAINST UNSAFE

PRACTICES

WARNING INDICATES A POTENTIALLY HAZARDOUS SITUATION

WHICH, IF NOT AVOIDED COULD RESULT IN SERIOUS INJURY

OR DEATH.

IMPORTANT OR INSTRUCTIONS INDICATES A PROCEDURES

ESSENTIAL FOR SAFE OPERATION AND WHICH, IF NOT FOL-

LOWED, MAY RESULT IN A MALFUNCTION OR DAMAGE TO THE

MACHINE.

The purpose of this manual is to provide users with the operating procedures essential for the promotion of

proper machine operation for its intended purpose. It is important to over-stress proper machine usage. All

information in this manual should be READ and UNDERSTOOD before any attempt is made to operate the

machine. YOUR OPERATING MANUAL IS YOUR MOST IMPORTANT TOOL - Keep it with the machine.

REMEMBER ANY EQUIPMENT IS ONLY AS SAFE AS THE OPERATOR.

BECAUSE THE MANUFACTURER HAS NO DIRECT CONTROL OVER MACHINE APPLICATION AND

OPERATION, PROPER SAFETY PRACTICES ARE THE RESPONSIBILITY OF THE USER AND HIS OPER-

ATING PERSONNEL.

ALL INSTRUCTIONS IN THIS MANUAL ARE BASED ON THE USE OF THE MACHINE UNDER PROPER

OPERATING CONDITIONS, WITH NO DEVIATIONS FROM THE ORIGINAL DESIGN. ALTERATION AND/OR

MODIFICATION OF THE MACHINE IS STRICTLY FORBIDDEN, WITHOUT WRITTEN APPROVAL FROM

JLG INDUSTRIES, PER OSHA REGULATIONS AND APPLICABLE ANSI STANDARDS.

THIS SAFETY ALERT SYMBOL IS USED TO CALL ATTENTION TO POTENTIAL HAZARDS WHICH

MAY LEAD TO SERIOUS INJURY OR DEATH IF IGNORED.

Safety of personnel and proper use of the machine are of primary concern, DANGER, WARNING, CAU-

TION, IMPORTANT, INSTRUCTIONS and NOTE are inserted throughout this manual to emphasize these

areas. They are defined as follows:

JLG INDUSTRIES MAY HAVE ISSUED SAFETY RELATED BULLETINS FOR YOUR JLG PRODUCT. CONTACT JLG INDUSTRIES INC.

OR THE LOCAL AUTHORIZED JLG DISTRIBUTOR FOR INFORMATION CONCERNING SAFETY RELATED BULLETINS WHICH MAY

HAVE BEEN ISSUED FOR YOUR JLG PRODUCT. ALL ITEMS REQUIRED BY THE SAFETY RELATED BULLETINS MUST BE COM-

PLETED ON THE AFFECTED JLG PRODUCT

Due to continuous product improvements, JLG Industries, Inc. reserves the right to make specification changes without prior notifica-

tion. Contact JLG Industries, Inc. for updated information.

FOREWORD

b– JLG Sizzor – 3120877

This page left blank intentionally.

FOREWORD

3120877 – JLG Sizzor – c

All procedures herein are based on the use of the

machine under proper operating conditions, with no

deviations from original design intent... as per OSHA

regulations and applicable ANSI standards.

READ & HEED!

The ownership, use, service, and/or maintenance of

this machine is subject to various governmental and

local laws and regulations. It is the responsibility of

the owner/user to be knowledgeable of these laws

and regulations and to comply with them. The most

prevalent regulations of this type in the United States

are the Federal OSHA Safety Regulations*. Listed

below, in abbreviated form are some of the require-

ments of Federal OSHA regulations in effect as of the

date of publication of this handbook.

The listing of these requirements shall not relieve

the owner/user of the responsibility and obligation

to determine all applicable laws and regulations and

their exact wording and requirements, and to com-

ply with the requirements. Nor shall the listing of

these requirements constitute an assumption of

responsibility of liability on the part of JLG Indus-

tries, Inc.

1. Only trained and authorized operators shall be

permitted to operate the aerial lift.

2. A malfunctioning lift shall be shut down until

repaired.

3. The controls shall be plainly marked as to their

function.

4. The controls shall be tested each day prior to

use to determine that they are in safe operating

condition.

5. All personnel in the platform shall, at all times,

wear approved fall protection devices and

other safety gear as required.

6. Load limits specified by the manufacturer shall

not be exceeded.

7. Instruction and warning placards must be legi-

ble.

8. Aerial lifts may be field modified for uses other

than those intended by the manufacturer only if

certified in writing by the manufacturer to be in

conformity to JLG requirements and to be at

least as safe as it was prior to modification.

9. Aerial lifts shall not be used near electric power

lines unless the lines have been de energized

or adequate clearance is maintained.

10. Employees using aerial lifts shall be instructed

on how to recognize and avoid unsafe condi-

tions and hazards.

11. Ground controls shall not be operated unless

permission has been obtained from personnel

in the platform, except in case of an emer-

gency.

12. Regular inspection of the job site and aerial lift

shall be performed by competent persons.

13. Personnel shall always stand on the floor of the

platform, not on boxes, planks, railing or other

devices, for a work position.

*Applicable Federal OSHA regulations for the

United States, as of the date of publication of this

manual, include, but are not limited to, 29 CFR

1910.67, 29 CFR 1926.20, 29 CFR 1926.21, 29 CFR

1926.28, and 29 CFR 1926.453.

FOREWORD

d– JLG Sizzor – 3120877

REVISON LOG

January 1999 - Original Issue

March 12, 1999 - Revised

March 1, 2001 Revised

July 31, 2001 Revised

July 23, 2012 Revised

3120877 – JLG Sizzor – i

TABLE OF CONTENTS

SUBJECT - SECTION, PARAGRAPH PAGE NO.

SECTION - FOREWORD

SECTION 1 - SAFETY PRECAUTIONS

1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.2 Pre-operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

1.3 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

1.4 Towing, Lifting, and Hauling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

1.5 Additional Hazards / Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

SECTION 2 - PREPARATION AND INSPECTION

2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

2.2 Preparation For Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

2.3 Delivery and Frequent Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

2.4 Daily Walk-Around Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

2.5 Daily Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2

2.6 Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

2.7 Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

SECTION 3 - USER RESPONSIBILITIES AND MACHINE CONTROL

3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

3.2 Personnel Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

3.3 Operating Characteristics and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1

3.4 Controls and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2

3.5 Placards and Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7

SECTION 4 - MACHINE OPERATION

4.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

4.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

4.3 Motor Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1

4.4 Raising and Lowering (Lifting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

4.5 Platform Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

4.6 Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

4.7 Traveling (Driving) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3

4.8 Parking and Stowing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4.9 Platform Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4.10 Safety Prop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4.11 transporting, Tie Down and Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4.12 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

SECTION 5 - EMERGENCY PROCEDURES

5.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

5.2 Incident Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

5.3 Emergency Towing Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

5.4 Manual Descent System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

5.5 Emergency Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1

SECTION 6 - INSPECTION AND REPAIR LOG

ii – JLG Sizzor – 3120877

TABLE OF CONTENTS (Continued)

LIST OF FIGURES

FIGURE NO. TITLE PAGE NO.

2-1. Pothole Protection System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

2-2. Daily Walk-Around Inspection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4

2-3. Daily Walk-Around Inspection Points (Sheet 1 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5

2-4. Daily Walk-Around Inspection Points (Sheet 2 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

2-5. Lubrication Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

2-6. Torque Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8

3-1. Ground Control Station - Models 1532E3/1932E3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3

3-2. Ground Control Station - Models 2033E3/2046E3/2646E3/2658E3 . . . . . . . . . . . . . . . . . . . . . . .3-4

3-3. Platform Control Station - All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5

3-4. Decal Installation - 1532E3 & 1932E3 UK (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8

3-5. Decal Installation - 1532E3 & 1932E3 UK (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9

3-6. Decal Installation - 1532E3 & 1932E3 Australian (Sheet 1 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . .3-10

3-7. Decal Installation - 1532E3 & 1932E3 Australian (Sheet 2 of 2). . . . . . . . . . . . . . . . . . . . . . . . . . .3-11

3-8. Decal Installation - 1532E3 & 1932E3 Dutch (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-12

3-9. Decal Installation - 1532E3 & 1932E3 Dutch (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-13

3-10. Decal Installation - 1532E3 & 1932E3 French (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-14

3-11. Decal Installation - 1532E3 & 1932E3 French (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-15

3-12. Decal Installation - 1532E3 & 1932E3 German (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

3-13. Decal Installation - 1532E3 & 1932E3 German (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-17

3-14. Decal Installation - 1532E3 & 1932E3 italian (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18

3-15. Decal Installation - 1532E3 & 1932E3 italian (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19

3-16. Decal Installation - 1532E3 & 1932E3 Spanish (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20

3-17. Decal Installation - 1532E3 & 1932E3 Spanish (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-21

3-18. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 UK (Sheet 1 of 2) . . . . . . . . . . . . . . . . . . .3-22

3-19. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 UK (Sheet 2 of 2) . . . . . . . . . . . . . . . . . . .3-23

3-20. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Australian (Sheet 1 of 2) . . . . . . . . . . . . .3-24

3-21. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Australian (Sheet 2 of 2) . . . . . . . . . . . . .3-25

3-22. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Dutch (Sheet 1 of 2) . . . . . . . . . . . . . . . .3-26

3-23. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Dutch (Sheet 2 of 2) . . . . . . . . . . . . . . . .3-27

3-24. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 French (Sheet 1 of 2) . . . . . . . . . . . . . . .3-28

3-25. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 French (Sheet 2 of 2) . . . . . . . . . . . . . . .3-29

3-26. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 German (Sheet 1 of 2). . . . . . . . . . . . . . .3-30

3-27. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 German (Sheet 2 of 2). . . . . . . . . . . . . . .3-31

3-28. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Italian (Sheet 1 of 2) . . . . . . . . . . . . . . . .3-32

3-29. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 italian (Sheet 2 of 2) . . . . . . . . . . . . . . . .3-33

3-30. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Spanish (Sheet 1 of 2). . . . . . . . . . . . . . .3-34

3-31. Decal Installation - 2033E3/2046E3/2646E3 & 2658E3 Spanish (Sheet 2 of 2). . . . . . . . . . . . . . .3-35

4-1. Grade and Sideslope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4-2. E3 Tie Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4-3. Lifting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

LIST OF TABLES

TABLE NO. TITLE PAGE NO.

1-1 Minimum Safe Approach Distances (M.S.A.D.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

2-1 Lubrication Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-7

6-1 Inspection and Repair Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

SECTION 1 - SAFETY PRECAUTIONS

3120877 – JLG Lift – 1-1

SECTION 1. SAFETY PRECAUTIONS

1.1 GENERAL

This section outlines the necessary precautions for proper

and safe machine usage and maintenance. For proper

machine use, it is mandatory that a daily routine is estab-

lished based on the content of this manual. A mainte-

nance program, using the information provided in this

manual and the Service and Maintenance Manual, must

also be established by a qualified person and followed to

ensure that the machine is safe to operate.

The owner/user/operator/lessor/lessee of the machine

should not operate this machine until this manual has

been read, training is accomplished, and operation of the

machine has been completed under the supervision of an

experienced and qualified operator.

If there are any questions with regard to safety, training,

inspection, maintenance, application, and operation,

please contact JLG Industries, Inc. (“JLG”).

FAILURE TO COMPLY WITH THE SAFETY PRECAUTIONS LISTED

IN THIS MANUAL COULD RESULT IN MACHINE DAMAGE, PROP-

ERTY DAMAGE, PERSONAL INJURY OR DEATH.

1.2 PRE-OPERATION

Operator Training and Knowledge

• Read and understand this manual before operating the

machine.

• Do not operate this machine until complete training is

performed by authorized persons.

• Only authorized and qualified personnel can operate

the machine.

• Read, understand, and obey all DANGERS, WARN-

INGS, CAUTIONS, and operating instructions on the

machine and in this manual.

• Use the machine in a manner which is within the scope

of its intended application set by JLG.

• All operating personnel must be familiar with the emer-

gency controls and emergency operation of the

machine as specified in this manual.

• Read, understand, and obey all applicable employer,

local, and governmental regulations as they pertain to

operation of the machine.

Workplace Inspection

• The operator is to take safety measures to avoid all

hazards in the work area prior to machine operation.

• Do not swing turntable or raise the platform while on

trucks, trailers, railway cars, floating vessels, scaffolds

or other equipment unless approved in writing by JLG.

• Do not operate the machine in hazardous environ-

ments unless approved for that purpose by JLG.

• Be sure that the ground conditions are able to support

the maximum load shown on the decals located on the

machine.

• This machine can be operated in temperatures of -20o

C to 40oC (0oF to 104oF). Consult JLG for operation

outside this range.

SECTION 1 - SAFETY PRECAUTIONS

1-2 – JLG Lift – 3120877

Machine Inspection

• Before machine operation, perform inspections and

functional checks. Refer to Section 2 of this manual for

detailed instructions.

• Do not operate this machine until it has been serviced

and maintained according to requirements specified in

the Service and Maintenance Manual.

• Be sure all safety devices are operating properly. Mod-

ification of these devices is a safety violation.

• Do not operate any machine on which safety or

instruction placards or decals are missing or illegible.

• Avoid any buildup of debris on the platform floor. Keep

mud, oil, grease, and other slippery substances from

footwear and platform floor.

1.3 OPERATION

General

• Do not use the machine for any purpose other than

positioning personnel, their tools, and equipment.

• Never operate a machine that is not working properly.

If a malfunctions occurs, shut down the machine.

• Never slam a control switch or lever through neutral to

an opposite direction. Always return switch to neutral

and stop before moving the switch to the next function.

Operate controls with slow and even pressure.

• Hydraulic cylinders should never be left fully extended

or fully retracted before shutdown or for long periods of

time.

• Do not allow personnel to tamper with or operate the

machine from the ground with personnel in the plat-

form, except in an emergency.

• Do not carry materials directly on platform railing

unless approved by JLG.

• When two or more persons are in the platform, the

operator shall be responsible for all machine opera-

tions.

• Always ensure that power tools are properly stowed

and never left hanging by their cord from the platform

work area.

• Supplies or tools which extend outside the platform are

prohibited unless approved by JLG

• Do not assist a stuck or disabled machine by pushing,

pulling, or by using machine functions. Only pull the

unit from the tie-down lugs on the chassis.

• Stow elevating assembly and shut off all power before

leaving machine.

Trip and Fall Hazards

• When operating a boom lift or vertical mast lift, occu-

pants in the platform must wear a full body harness

with a lanyard attached to an authorized lanyard

anchorage point. When operating a scissor lift or verti-

cal mast lift, JLG recommends wearing a full body har-

ness. Attach only one (1) lanyard per lanyard

anchorage point.

• Before operating the machine, make sure all gates are

closed and fastened or in their proper position.

• Keep both feet firmly positioned on the platform floor at

all times. Never use ladders, boxes, steps, planks, or

similar items on platform to provide additional reach.

• Never use the elevating assembly to enter or leave the

platform.

• Use extreme caution when entering or leaving plat-

form. Be sure that the platform is fully lowered. Face

the machine, maintain “three point contact” with the

machine, using two hands and one foot or two feet and

one hand during entry and exit.

• Check orientation of directional arrows on chassis

before driving. The direction of drive and steer may be

opposite from normal operation based upon orienta-

tion of chassis.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JLG Hebesystem Handbücher

JLG

JLG E450A Gebrauchs- und Pflegehandbuch

JLG

JLG 400S Installations- und Benutzerhandbuch

JLG

JLG LiftPod FT70 Installations- und Benutzerhandbuch

JLG

JLG 600SC Bedienungsanleitung

JLG

JLG X1000AJ Gebrauchs- und Pflegehandbuch

JLG

JLG 1930ES Bedienungsanleitung

JLG

JLG Skytrak 6036 Gebrauchs- und Pflegehandbuch

JLG

JLG 25RTS Installations- und Benutzerhandbuch

JLG

JLG 3369electric Installations- und Benutzerhandbuch

JLG

JLG 260MRT Bedienungsanleitung

JLG

JLG 400S Bedienungsanleitung

JLG

JLG T350 Installations- und Benutzerhandbuch

JLG

JLG TOUCAN 861 Bedienungsanleitung

JLG

JLG 1932RS/6RS Installations- und Benutzerhandbuch

JLG

JLG 3394RT Installations- und Benutzerhandbuch

JLG

JLG TH336 Bedienungsanleitung

JLG

JLG X430AJ Gebrauchs- und Pflegehandbuch

JLG

JLG 400SJ Gebrauchs- und Pflegehandbuch

JLG

JLG 3507 Betriebsanleitung

JLG

JLG 1200SJP Gebrauchs- und Pflegehandbuch

JLG

JLG 1230ES Installations- und Benutzerhandbuch

JLG

JLG RT2669 Installations- und Benutzerhandbuch

JLG

JLG 600A Gebrauchs- und Pflegehandbuch

JLG

JLG G6-42A Leitfaden

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung