JLG G6-42A Leitfaden

31200680

1.1 GENERAL GUIDELINES

•This repair procedure provides repair information for

a specific discrepancy. It is the responsibility of the

entity performing the repairs to determine if the

discrepancy can be corrected by this procedure. This

repair is only for the replacement of the rear axle

weldment.

•After inspection, if only weld cracks and NO plate

deflection is found, refer to instructions 31212011.

•After inspection, if weld cracks AND plate deflection

is found, complete the Rear Axle Block Weldment

Replacement Instructions.

1.2 WELD REPAIR GUIDELINES

•All welding must be in accordance with ANSI/AWS

D1.1 Standard.

•Disconnect the battery of the machine being repaired

prior to welding.

•Ground only to the component being welded. Do not

ground to any adjacent component or allow pins,

wear pads, wire ropes, bearings, gears, seals,

valves, electrical wiring, or hoses to be between the

grounding position and the area to be welded.

1.3 TOOLS & EQUIPMENT REQUIRED

1. Stands and lifting equipment capable of lifting/

supporting the affected components

2. Hand-held power grinder

3. Air carbon-arc equipment

4. Electric welding equipment

5. AWS 70 grade, low hydrogen rod or wire

6. Standard welder tools

7. Standard mechanic tools

8. Paint

1.4 PERSONNEL REQUIRED

1. Qualified JLG Equipment Mechanic

2. Certified Welder

1.5 PARTS LIST

1.6 REAR AXLE BLOCK WELDMENT

REPLACEMENT

1. Remove any attachment from the machine.

2. Park the machine on a firm, level surface with the

machine level, retract and level the boom. Place the

transmission control lever in the (N)

NEUTRAL position and engage the

parking brake. Shut the engine OFF.

3. Place a Do Not Operate Tag on both the

ignition key switch and the steering

wheel, stating that the machine should

not be operated.

4. Open the engine cover. Allow system

fluids to cool.

5. Properly disconnect the battery.

6. Properly support the frame to alleviate

pressure or stress at the affected repair

area.

7. Remove components as required to

facilitate repair. Refer to the machine

Service Manual for proper disassembly

procedures.

NOTICE

Reference the Service Manual for safe and proper

disassembly/assembly procedures.

NOTICE

Failure to comply with the above weld repair guidelines

may result in component damage.

P/N Qty Description

91476013 1 Rear Axle Weldment Block

G6-42A

Rear Axle Block Weldment

Replacement Instructions

For Kit 1001126991

7/14

31200680

An Oshkosh Corporation Company

2 31200680

G6-42A Rear Axle Block Weldment Replacement Instructions For Kit 1001126991

8. Protect any hoses, wires and hydraulic cylinder rods

before preparing or welding in the axle mount area.

9. Use air carbon-arc equipment or a portable power

grinder to remove the damaged rear axle mount

weldments (4) from the frame weldment.

10. Inspect the affected areas for cracks. If any

discrepancies are evident, notify a certified welder for

further evaluation.

11. Prepare the repair area (5) for the installation of the

new rear axle weldment.

12. Locate the Axle Weldment (6) P/N 91476013 using

1.6.1 “Rear Axle Weldment Welding Locations” on

page 3. Tack weld into position.

13. Weld the rear axle weldment into place using the

recommended weld material.

14. Inspect welds using the magnetic particle or dye-

penetrant inspection methods to assure there are no

cracks or deformities. If any cracks or deformities

exist, grind to remove affected area(s) and repeat the

weld and inspection procedures.

15. Remove the weld bars (7) from the rear axle

weldment.

16. Clean, prime and paint the affected areas.

17. Install previously removed components. Refer to the

machine Service Manual for proper assembly

procedures.

18. Remove all protective coverings from any hoses,

wires and hydraulic cylinder rods.

19. Properly connect the battery.

20. Close and secure the engine cover.

21. Cycle the drive, steer and frame level functions a

minimum of five times.

22. Verify proper clearance between the frame, rear axle,

hydraulic hoses and electrical wires.

23. Install the previously removed attachment.

24. Remove the Do Not Operate Tag from the ignition

key switch and the steering wheel.

25. Return machine to service.

NOTICE

Do not damage the parent metal during this procedure.

MY5230

MY5250

NOTICE

Do not damage the rear axle weldment during this

procedure.

MY4420

31200680

G6-42A Rear Axle Block Weldment Replacement Instructions For Kit 1001126991

1.6.1 Rear Axle Weldment Welding Locations

A. 1.0 in (25,4 mm)

5/16

WELD ALL AROUND EXCEPT AGAINST REAR PLATE

3/8

MY5260

4 31200680

G6-42A Rear Axle Block Weldment Replacement Instructions For Kit 1001126991

This Page Intentionally Left Blank

Andere Handbücher für G6-42A

Andere JLG Hebesystem Handbücher

JLG

JLG LiftPod FT70 Installations- und Benutzerhandbuch

JLG

JLG 680S Installations- und Benutzerhandbuch

JLG

JLG T350 Installations- und Benutzerhandbuch

JLG

JLG 800A Gebrauchs- und Pflegehandbuch

JLG

JLG Toucan 12E Installations- und Benutzerhandbuch

JLG

JLG 1230ES Installations- und Benutzerhandbuch

JLG

JLG 10VP Bedienungsanleitung

JLG

JLG T500J Installations- und Benutzerhandbuch

JLG

JLG 25AM Gebrauchs- und Pflegehandbuch

JLG

JLG 1250AJP Bedienungsanleitung

JLG

JLG E450A Gebrauchs- und Pflegehandbuch

JLG

JLG 3513PS Gebrauchs- und Pflegehandbuch

JLG

JLG E400A Narrow Gebrauchs- und Pflegehandbuch

JLG

JLG 4108AN Gebrauchs- und Pflegehandbuch

JLG

JLG 330CRT Bedienungsanleitung

JLG

JLG 3507 Betriebsanleitung

JLG

JLG EcoLift50 Installations- und Benutzerhandbuch

JLG

JLG LiftPod FS60 Installations- und Benutzerhandbuch

JLG

JLG DVL Series Gebrauchs- und Pflegehandbuch

JLG

JLG 120HX Installations- und Benutzerhandbuch

JLG

JLG 260MRT Gebrauchs- und Pflegehandbuch

JLG

JLG G5-18A Bedienungsanleitung

JLG

JLG 19AMI Gebrauchs- und Pflegehandbuch

JLG

JLG Skytrak 6036 Gebrauchs- und Pflegehandbuch

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung