Jobsite CT1649 Bedienungsanleitung

230MM ANGLE GRINDER CT1649

Ref no. S1M-ZP15-230

INSTRUCTION MANUAL

SAVE THESE INSTRUCTIONS AND PRECAUTIONS.

READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.

Cannon Tools Limited

Address:20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM

EC DECLARATION OF CONFORMITY

WeCANNON TOOLS LTD

20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.

Declare that the following machine complies with the appropriate basic safety and

health requirements of the EC Directive based on its design and type, as brought

into circulation by us.

In case of alteration of the machine, not agreed upon by us, this declaration will

lose its validity.

Product description:

Model: CT1649 (Ref no. S1M-ZP15-230)

Applicable EC Directives:

EC Machinery Directive 2006/42/EC

EC Directive of Electromagnetic Compatibility 2014/30/EU

Harmonized standards：

EN 60745-1:2009+A11, EN 60745-2-3:2011+A2+A11+A12+A13,

EN 55014-1:2006+A1+A2, EN 55014-2:1997+A1+A2,

EN 61000-3-2:2014, EN 61000-3-3:2013

20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

Mr. Gurcharan Tony Singh Sanghera

Managing Director

CANNON TOOLS LTD

2020-10-20

230MM ANGLE GRINDER

PRODUCT SPECIFICATIONS

CAUTION

Carefully read through this entire instruction manual before using your new power tool.

Take special care to heed the Cautions and Warnings

TECHNICAL DATA

Model No. CT1649

Voltage: 230-240V/50Hz

Power 2380W

No Load Speed 6600/min

Disc diameter 230mm

Disc bore diameter 22.2

Spindle thread M14

Protection class Class Ⅱ

This tool is double insulated. There are two independent barriers of

insulation to protect you from the possibility of electric shock.

The power tools comes with a plug, the plug reach to BS1363/A standard,

with a 13Amp fuse.

NOISE AND VIBRATION DATA

Typical weighted Vibration 5.305m/s²

A weighted sound pressure 92dB(A)

A weighted Sound power 103dB(A)

Sound pressure is over 96dB(A)

The sound intensity level for the operator may exceed 96dB(A) and sound

protection measures are necessary.

You must always wear the following if operating this power tool.

Wear goggles.

Wear ear defenders.

Wear a breathing mask.

Wear safety gloves

Wear safety shoes

POWER TOOL SAFETY

SAFETY INSTRUCTIONS

To use this tool properly, you must observe

the safety regulations, the assembly

instructions and the operating instructions to

be found in this manual. All persons who use

and service the machine have to be

acquainted with this manual and must be

informed about any potential hazards.

Children and infirm people must not use this

tool. Children should be supervised at all

times if they are in the area in which the tool

is being used. It is also imperative that you

observe the accident prevention regulations

in force in your area. The same applies for

general rules of occupational health and

safety.

The manufacturer shall not be liable for any

changes made to the tool nor damage

resulting from such changes.

Even when the tool is used as prescribed it is

not possible to eliminate all residual risk

factors. The following hazards may arise in

connection with the tools construction and

design:

Contact with disc

Kickback of work piece and parts of work

piece.

Disc fracture.

Catapulting of disc pieces.

Damage to hearing if effective ear defenders

are not worn.

Damage to the lungs if an effective dust

mask is not worn.

Do not use discs that are damaged or

cracked.

Always remove the plug from the mains

socket before making any adjustments or

maintenance, including changing disc.

WARNING

When using electric power tools, basic

safety precautions including the following,

should always be followed to reduce the risk

of fire electric shock and personal injury.

Also please read and heed the advice given

in the additional important safety instructions

Read all these instructions before

operating this product and save

these instructions.

1. Keep the work area clean and tidy.

Cluttered work areas and benches invite

accidents and invite injury.

2. Consider work area environment.

Do not expose power tools to rain. Do not

use power tools in damp or wet locations.

Keep the work area well lit. Do not use

power tools where there is risk to cause

fire or explosion. Do not use power tools in

the presence of flammable liquids or

gases.

3. Guard against electric shock.

Avoid body contact with earthed or

grounded surfaces (e.g. pipes, radiators,

ranges, refrigerators).

4. Keep children and visitors away

from the work area.All visitors and

onlookers, especially children and infirm

persons should be kept well away from

where you are working. Do not let others in

the vicinity make contact with the tool or

extension cord?

5. Store idle tools.When not in use,

tools should be stored in a dry, high or

locked up place out of reach of children.

6. Do not force the tool.The tool will do

the job better and safer at the rate for

which it was designed.

7. Use the right tool.Do not force small

tools or attachments to do the job best

handled by a heavier duty tool. Do not

POWER TOOL SAFETY

use tools for purposes not intended; do not

use circular saws to cut tree limbs or logs.

8. Dress correctly.Do not wear

loose clothing or jewellery; they can be

caught in moving parts. Rubber gloves

and non-slip footwear are recommended

when working outdoors. Wear a protective

hair covering to contain long hair.

9. Use safety accessories.Safety

glasses and ear defenders should always

be worn. A face or dust mask is also

required.

10. Connect dust extraction

equipment.If devices are provided for

the connection of dust extraction and

collection facilities, ensure that these are

connected and properly used.

11. Do not abuse the power cord.

Never carry the tool by the cord or yank it

to disconnect it from the socket. Keep the

cord away from heat, oil and sharp edges.

12. Secure the work piece.Use

clamps or a vice to hold the work piece. It

is safer than using your hand and it frees

both hands to operate the tool.

13. Do not over reach.Keep

proper footing and balanced at all times.

14. Maintain and Look after your

tools with care.Keep cutting tools

clean and sharp for better and safer

performance. Follow the instructions for

lubrication and accessory changes.

Inspect tool cords periodically and if

damaged have it repaired by an

authorized service facility. Inspect

extension cords periodically and replace,

if damaged. Keep tool handles dry, clean

and free from oil and grease.

15. Disconnect tools. Switch off

the power.Disconnect the plug from

the power point before servicing and when

changing accessories such as blades, bits

and cutters, and when the tool is not in

use.

16. Remove adjusting keys and

wrenches.Form the habit of checking

to see that the keys and adjusting

wrenches are removed from the tool

before switching the tool on.

17. Avoid unintentional starting.

Ensure that the switch is in the OFF

position before plugging the tool to the

power supply. Do not carry a plugged in

tool with your finger on the switch.

18. Use outdoor rated extension

cords. When a tool is used outdoors, use

only extension cords that are intended for

outdoor use and are so marked.

19. Stay alert.Watch what you are

doing. Use common sense. Do not

operate a power tool when you are tired.

20. Check for damaged parts.

Before using a tool, check that there are

no damaged parts, if a part is slightly

damaged carefully determine if it will

operate properly and perform its intended

function other wise replace. Check for

alignment of moving parts binding of

moving parts, breakage of parts, free

running of moving parts, proper

mounting and any other conditions that

may affect the operation of the tool. A

guard or other parts that are damaged

should be properly repaired or replaced by

an authorised service centre, unless

otherwise indicated in this instruction

manual. Defective switches must be

replaced by authorised service facility. Do

not use the tool if the switch does not turn

the tool on and off correctly.

21. Warning. The use of any

accessory or attachment, other than those

recommended in this instruction manual,

may present a risk of personal injury.

POWER TOOL SAFETY

22. Have your tool repaired by a

qualified person.This electric tool is in

accordance with the relevant safety

requirements. Repairs should only be

carried out by qualified persons using

original spare parts; otherwise this may

result in considerable danger to the user.

23. Do not let the tool run

unattended.Always wait until your

power tool has come to a complete stop

before leaving it. Then turn off at mains and

remove the plug from the power outlet.

WARNING

The use of an accessory or attachment,

other than those recommended in this

instruction manual may present a risk of

personal injury

The tool must be used only for its prescribed

purpose any use other than those mentioned

in this manual will be considered a case of

misuse. The user and not the manufacture

shall be liable for any damage or injury

resulting from such cases of misuse.

ADDITION SAFETY RULES FOR

ANGLE GRINDER



Fully unwind cable drum extensions to

avoid potential overheating.



When an extension cable is required, you

must ensure that it has the right ampere

rating for your power tool and is in safe

electrical condition.



Ensure your mains supply voltage is the

same as your tool rating plate voltage.



Always switch off before you put the angle

grinder down.



Keep the area free of tripping hazards.



Do not let anyone under the age of 18

years operate this tool.



Rags, cloths, cord, string and the like

should never be left around the work area.



If you are interrupted when operating the

tool, complete the process and switch off

before looking up.



Periodically check that all the nuts, bolts

and other fixings are properly tightened.



Abrasive wheels shall be stored and

handled with care in accordance with

manufacturer instructions.



Do not store materials or equipment above

a machine in such a way that they could fall

into it.



Do not use discs having a maximum

permissible speed below the tool rated

marked RPM.



Inspect the grinding wheel before use, do

not use chipped, cracked or otherwise

defective products. Check the disc before

mounting it into the angle grinder. Check by

striking it with a wooden handle whilst

balancing the disc on your finger. Listen to

the sound it makes if it rings it is ok if it

sounds dull it may be cracked and needs to

be replaced.



Ensure that mounted wheels and points are

fitted in accordance with the manufacturer’s

instructions.



When the disc is installed, run it for at least

a minute to ensure that it does not have a

fault. It is always advisable to stay out of the

line of the disc when testing or in general

use.



Do not use a disc marked with a lower

RPM than that of the no load speed shown

on the rating plate.



Use discs only of the prescribed

diameter.



Never try to operate the angle grinder

without the guard in place.

POWER TOOL SAFETY



Do not use separate reducing bushings or

adaptors to adapt large hole abrasive

wheels.



For tools intended to be fitted with

threaded hole wheel, ensure that the thread

in the wheel is long enough to accept the

spindle length;



Do not use cutting off wheel for side

grinding.



Ensure that sparks resulting from use do

not create a hazard e.g. do not hit persons,

or ignite flammable substances.



Ensure that ventilation openings are kept

clear when working in dusty conditions. If it

should become necessary to clear dust, first

disconnect the tool from the mains supply

(use non metallic objects) and avoid

damaging internal parts.



If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person in order

to avoid hazard



Do not secure the angle grinder in a vice

or work bench and use it as a static grinder.

It leads to serious injury.



Never apply excessive pressure to the

disc it might shatter causing personal injury.



Ensure the work piece to be ground or

cut, is held tight in the vice or other clamping

system.



Always use both hands and ensure a

good handgrip on the grinder before

proceeding with any work.



Make sure that the disc is not in contact

with the work surface when you start the

grinder.



Be careful not to damage the spindle or

either of the disc flanges. Damage to these

parts could result in disc damage or

breakage.



Only use good quality grinding

discs. Cheap or poor quality discs tend to

glaze up which loads the motor and can

damage it. Use discs for their designated

purpose only. For instance, do not use

cutting discs for grinding or metal wheels for

masonry.



Watch out for flying sparks. Hold the tool

at an angle of approximately 15



to 30



to the

work piece surface when using discs.



Let the disc do the grinding at a

reasonable feed, as overloading will occur if

too much pressure is applied and the disc

slows resulting in inefficient grinding and

possible damage to the motor.



When using the grinder, use safety

equipment including safety goggles or shield,

ear protection dust mask and protective

clothing including safety gloves.

Wear goggles

Wear ear defenders

Wear a breathing mask

Wear safety gloves

Wear safety shoes

UNPACKING

Due to modern production techniques, it is

unlikely that your power tool is faulty or that

a part is missing. If you find anything wrong

do not operate the tool until the parts have

been replaced or the fault has been rectified.

Failure to do so could result in serious

personal injury.

KNOW YOUR PRODUCT

Before using the angle grinder, familiarise yourself with all the operating features and safety

requirements.

Use the tool and accessories only for the application intended all other applications are

expressly ruled out.

1 Motor housing 5 On/Off switch

2 Spindle lock button 7 Power cord

3 Disc guard 8 Pin wrench

4Handle for left hand or right hand 9 carbon brush

6 Side handle

4 2 3 6 1 5 8 9 7

CONTROLS AND OPERATION

CONTROLS

1/ Looking at the angle grinder from the top,

the spindle lock (2) is located at the front

top right hand side.

2/ There are attachment points (4) for the

handle (6) at either side of the front of the

housing, Attach the handle in the position

that suits the planned operation.

3/ An arrow imprinted on the front housing

indicates the direction of the rotation of the

Disc.

4/ The on/off switch (5) is located on the

top of the motor housing.

5/ The adjustable disc guard (3) is on the

underside of the grinder as is the outer

flange (9), grinding disc (10)

Operation

This angle grinder can be used for polishing

cutting and grinding.

1/ To start the grinder first ensure that the

work you are going to do has the right

disc for the job.

2/ When using cutting or grinding disc,

insure that the guard (3) and tools are

in good condition.

3/ Position the guard (3) when using disc

so that it will deflect hot sparks away from

operator.

4/ Plug the cord set into the mains outlet.

5/ Push the on/off switch (5) forward and

up over the latching ramp to lock the switch

on.

6/ Allow the grinder to start and attain full

speed before bringing the grinder to the work

piece.

7/ When using cutting and grinding discs

hold the grinder at 15



to 30



to the work

surface moving slowly

8/ Hold the grinder firmly while it is

switched on and only apply gentle pressure

to the work piece little more than the weight

of the tool should be applied to give the best

and most efficient material removal. Forcing

and excessive pressure can cause

dangerous disc fracture or damage to the

tool.

9/ Avoid flying sparks. And ensure they do

not hit any inflammable materials, as they

are very hot and could cause personal injury

or a fire.

10/ Once you have finished the job you are

doing, press the back of the switch (5) and

lift it over the latching ramp to stop the angle

grinder.

11/ If a person comes to you while you are

operating the machine do not turn round or

look up until you have released the trigger

and the machine has come to a stop and you

have put the machine down then you are

safe to communicate with that person.

12/ WARNING. The grinder continues for a

few seconds after the trigger has been

released, so be careful when placing the tool

down, make sure it has stopped.

FITTING GRINDING DISC

FITTING A GRINDING DISC

Caution.: Switch off the grinder and

disconnect it from the power point.

1/Turn the angle grinder

on to its back and press

the spindle lock button.

2/ Rotate the spindle

unit until it locks.

3/ Insert the pins of the

wrench into the holes in

the outer flange and

remove it and the old disc.

4/ Do not remove the inner flange.

5/ Select the type of disc needed for the

Job on hand.

6/ Clean the flanges and check the new disc.

7/ Holding the angle

grinder with the spindle

facing upwards, check

that the inner flange is

on the spindle and correctly located.

The two-machined flat sections must face

the angle grinder and locate in the

appropriate position on the spindle.

8/ Place the grinding disconnect to the

spindle with label facing the angle grinder.

The hole in the discs should locate onto

the spindle and fit firmly of the inner flange.

9/ Screw the outer flange with the

protruding spigot section Facing the

angle grinder. The

spigot section must

locate with the hole

in the grinding disc.

10/ Hand tighten the outer flange until

the disc issue cure.

11/ Press the spindle

lock button and tighten

the flange with the

wrench.

12/ Turn the new disc by hand, ensuring

that it is tightly secured and that it

rotates fully and does not wobble unduly.

13/ Run the angle grinder under no load

for at least one minute to ensure the

new disc is in good condition. Make

sure you are wearing all the safety

items mentioned in the Safety Rules

and that you face the grinder away

from you.

CAUTION

Do not use excessive force to clamp the

disc. It could crack and cause failure

during use.

WARNING

Do not immerse the disc into any type of

lubrication including water.

This angle grinder is designed as a dry

grinder/cutter/polisher.

Failure to observe this warning could result

in a fatal shock.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Jobsite Schleifer Handbücher

Jobsite

Jobsite CT0827 Bedienungsanleitung

Beliebte Schleifer Handbücher anderer Marken

Parkside

Parkside PWS 230 C3 Bedienungsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Technisches Handbuch

PTA

PTA P1322 Bedienungsanleitung

Crown

Crown CT13313 Bedienungsanleitung

Parkside

Parkside 280250 Bedienungsanleitung

Climax

Climax VM2150 Series Bedienungsanleitung

Jet

Jet JPSG-618M1 Service-Handbuch

Makita

Makita GA4030 Bedienungsanleitung

DeWalt

DeWalt DWEN202 Bedienungsanleitung

Grizzly

Grizzly G2790 Bedienungsanleitung

Fein

Fein MSf843-1a Bedienungsanleitung

Bosch

Bosch GWS 14,4 V PROFESSIONAL Bedienungsanleitung

RAMSET

RAMSET CBAGR18 Bedienungsanleitung

Bosch

Bosch 8-115 Z Bedienungsanleitung

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Bedienungsanleitung

MW TOOLS

MW TOOLS ME15W Bedienungsanleitung

Caravaggi

Caravaggi SP 20 Betriebsanleitung

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Technisches Handbuch