Johnson Controls LP-FXGPRSU-0 Bedienungsanleitung

FX22/FX62 Supervisory Controller GPRS Modem Option Card Installation Instructions 1

Applications

This document describes the mounting and cabling of a

General Packet Radio Service (GPRS) wireless

modem option kit for FX22/FX62 Supervisory

Controllers without the factory-installed onboard GPRS

modem (models LP-FX2211T-0 and LP-FX6211T-0).

This GPRS modem option card is a Global System for

the Mobile Communications (GSM) cellular modem

option card that uses GPRS data technology. The

option card has two Light-Emitting Diodes (LEDs) to

indicate status and signal.

The GPRS modem option card installs into the only

option card slot in the FX22/FX62 Supervisory

Controller.

The GPRS modem option card is not supported if the

FX22/FX62 Supervisory Controller has the

factory-installed onboard GPRS modem (models

LP-FX2213T-0 and LP-FX6213T-0).

At the time of this document, only a Subscriber Identity

Module (SIM) card provisioned by the Wyless™ Group

is supported for use in the United States.

For the software configuration and operation of the

installed GPRS modem option, refer to:

• FX GPRS Modem Technical Bulletin

(LIT-12011639)

For information on mounting and wiring an FX22/FX62

Supervisory Controller, refer to:

• FX22/FX62 Supervisory Controller Installation

Instructions (Part No. 24-10564-9)

For installation details on the GPRS modem option

(LP-FXGPRS-0) for FX20/FX60/FX70 Supervisory

Controllers, refer to:

•FX20/FX60/FX70 GPRS Installation Instructions

(Part No. 24-10564-68)

North American Emissions Compliance

United States

Canada

This equipment has been tested and found to

comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when this equipment is

operated in a commercial environment. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference, in which case

the user will be required to correct the interference

at his/her own expense.

This Class (A) digital apparatus meets all the

requirements of the Canadian Interference Causing

Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte

toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

LEDs (2):

Status

Signal

Supplied

Stub

Antenna

SMA Coax

Cable and

Mounting

Bracket for

connecting

Antenna

FIG:fx22_62_gprs_kt

Figure 1: FX22/FX62 GPRS Modem Option Kit

FX22/FX62 Supervisory Controller

GPRS Modem Option Card

Installation Instructions

LP-FXGPRSU-0

Part No. 24-10564-25, Rev. —

Issued October 29, 2010

FX22/FX62 Supervisory Controller GPRS Modem Option Card Installation Instructions2

Installation

Parts Included

This package includes the following items:

• a GPRS modem option card, with pre-attached end

plate

• a Wyless provisioned SIM card, ready for

Pre-installation

• a right-angle GSM/GPRS quad-band SubMiniature

version A (SMA) coax mounted stub antenna

• an antenna mounting bracket

• a 6.56 ft (2 m) SMA coax antenna cable

•thisFX22/FX62 Supervisory Controller GPRS

Modem Option Card Installation Instructions (Part

No. 24-10564-25)

Special Tools Needed

The following supplies and tools are required:

• #1 and #2 Phillips screwdrivers: to remove and

refasten covers on the FX22/FX62 Supervisory

Controller, and to install the GPRS modem card.

• Any other tools needed for mounting the antenna

bracket. See Figure 8 for bracket details.

Mounting

Pre-installation

Prior to mounting the GPRS

modem option card in the

FX22/FX62 Supervisory Controller, install the SIM card

into the connector on the underside of the option card.

To install the SIM card, orient the card with its foil

connectors down (writing side up) and its angled corner

out

, and slide the card fully into the connector (see

Figure 2).

Mounting the GPRS Modem Option Card

Mount the GPRS modem option card in the only option

card slot of the FX22/FX62 Supervisory Controller.

1. Remove power from the FX22/FX62 Supervisory

Controller. Wait for all LEDs to turn off.

2. Use a #1 Phillips screwdriver to remove the right

cover first (see Figure 3). Set the two screws aside.

3. Remove the left cover next (see Figure 4). Set the

two screws aside.

SIM Card SIM Card

seated fully

in connector

Angled corner out

FIG:fx_sim_crd_gprs

Figure 2: Inserting SIM Card into Underside of

GPRS Modem

WARNING: Risk of Electric Shock.

Disconnect power supply before making

electrical connections. Contact with

components carrying hazardous voltage

can cause electric shock and may result

in severe personal injury or death.

IMPORTANT: Be careful to plug any option card

into its connector properly (pins aligned).

Right cover

screws (2)

FIG:fx_22_62_rmv_rt_cvr

Figure 3: Right Cover Removal and Replacement

FX22/FX62 Supervisory Controller GPRS Modem Option Card Installation Instructions 3

4. Use a #2 Phillips screwdriver to remove the

blanking plate from the FX22/FX62 Supervisory

Controller’s option card slot.

5. Carefully insert the pins of the GPRS modem

option card into the socket of the option card slot.

Line up the mounting holes on the end plate with

the standoffs on the base board. If the mounting

holes and standoffs do not line up, the connector is

not properly aligned.

6. Press the option card until it is completely seated.

7. Place the two screws through the option card end

plate and into the standoffs on the FX22/FX62

Supervisory Controller base board. Hand tighten

these screws (see Figure 6).

8. Replace the left cover (see Figure 4) and refasten

with the two screws set aside.

Note: Leave the right cover off for the Antenna

Installation. You may wish to leave the right cover off

until you complete Modem Checkout on page 4, so you

can see the LEDs.

Left cover

screws (2)

Option Card Slot

FIG:fx22_62_rmv_lft_cvr

Figure 4: Left Cover Removal and Replacement

Figure 5: Insert the GPRS Modem Option Card

with Pins Aligned

Insert GPRS

modem option

card into empty

option card slot.

FIG:fx22_62_insrt_optn_crd

Figure 6: GPRS Modem Option Card Inserted,

Screws Tightened

Make sure that the GPRS

option card pins are aligned.

Fully seat the card.

Hand tighten the screws

using a screwdriver.

FIG:fx22_62)gprs_mod_insrtd

FX22/FX62 Supervisory Controller GPRS Modem Option Card Installation Instructions4

Antenna Installation

1. Route the included SMA coax cable through the

appropriate wiring knockout of the FX22/FX62

Supervisory Controller (top, bottom, or back), and

attach the cable to the GPRS modem option card

(see Figure 7).

2. Mount the antenna bracket within reach of the

6.56 ft (2 m) SMA-type coax extension cable.

Figure 8 shows the bracket details and

dimensions.

3. Fasten the end of the SMA coax cable in the

mounting bracket and attach the antenna by finger

tightening the knurled nut.

4. Rotate the antenna to whatever position you need

for mounting clearance and/or best reception.

Note: Some installations may require a different

external antenna.

Note: Any external antenna must be compatible with

the GSM 900/1,800 frequency and the 50-ohm

impedance of the SMA coax connector on the GPRS

modem option.

Operation

LEDs

Two LEDs appear on the end plate of the GPRS

modem option card. On the option card label, these

LEDs appear as STATUS and SIGNAL (Figure 1).

These two LEDs are briefly described as follows:

• STATUS (green) — Flashes various LED patterns

based on the state of the modem. This LED is

directly under control of the modem itself (rather

than the modem driver).

Upon initial power-up, the Status LED pattern is

typically 600 ms On/600 ms Off, and may change

depending on various modem state changes.

• SIGNAL (green) — Indicates the Received Signal

Strength Indicator (RSSI), according to the number

of short (350 ms On) flash patterns. (Analogous to

number of bars on a cell phone.)

For further details on the operation of both LEDs, refer

to the FX GPRS Modem Technical Bulletin

(LIT-12011639).

Modem Checkout

Note: The controller’s right cover must be off to see

the two LEDs on the GPRS modem option card. After

modem checkout, replace the right cover (see

Figure 3).

After mounting the GPRS option card and completing

the antenna installation, power on the FX22/FX62

Supervisory Controller. Following a reboot of the

FX22/FX62 Supervisory Controller, you can configure

the modem by opening a platform connection to the

FX22/FX62.

To verify modem communications, verify that status

properties in the GPRS Modem Configuration

platform view display returned values.

Figure 7: SMA Coax Cable

Routed Through Knockout

FX22/FX62

Route SMA

coax cable

through

wiring

knockout.

6.56 ft

(2 m)

To bracket

and stub

antenna.

Attach SMA

coax cable

to option

card

connector.

FIG:fx22_62_sma_cax_cb

StubAntenna

Bracket

SMA-type

coax

extension

cable

1.0 (25.4)

.625

(15.9)

.170

(4.32)

1.13

(28.7)

1.25 (31.8)

.251

(6.37)

2.0

(50.8)

.625

(15.9)

.236

(6.0)

Mounting Holes (2)

FIG:fx_SED_ext_brkt_detls_sma

Figure 8: Extension Cable and Antenna

Mounting Bracket Dimensions, in. (mm)

Published in U.S.A. www.johnsoncontrols.com

FX22/FX62 Supervisory Controller GPRS Modem Option Card Installation Instructions 5

Johnson Controls® is a registered trademarks of Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Repair Information

If the GPRS modem option card fails to operate within

its specifications, replace the unit. For a replacement

GPRS option card, contact the nearest

Johnson Controls® representative.

Options and Parts

Standard replacement parts are listed in Table 1.

Approvals

Federal Communications Commission (FCC): The

Siemens® TC63 cellular communications module used

on the LP-FXGPRSU-0 modem option card is FCC

approved, and has an FCC ID of QIPTC63.

COM Slot Assignments

Table 2 lists the COM slot assignments for the

FX22/FX62 Controller with a GPRS modem.

Table 1: Parts for GPRS Modem Option Card

Order Code Description

LP-FXGPRSE-0 Includes a 6.56 ft (2 m) SMA-type

coax extension cable and steel

bracket for wall or panel mounting

of the GPRS Modem antenna.

LP-FXGPRSS-0 ReplacementSIMcard,provisioned

by Wyless.

LP-KITGPRSA-0 Replacement right-angle

GSM/GPRS quad-band SMA coax

mounted stub antenna.

Table 2: COM Slot Assignments for the FX22/FX62

Controller with a GPRS Modem

FX22/FX62

Only one GPRS card supported

Option Slot

GPRS = COM7, COM8

Inhaltsverzeichnis

Andere Johnson Controls Steuereinheit Handbücher

Johnson Controls

Johnson Controls GS Series Bedienungsanleitung

Johnson Controls

Johnson Controls tyco AMD-1 Bedienungsanleitung

Johnson Controls

Johnson Controls METASYS NU-XBN101-0 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls C450CCN-2 Bedienungsanleitung

Johnson Controls

Johnson Controls System 450 Series Bedienungsanleitung

Johnson Controls

Johnson Controls A19 Series Bedienungsanleitung

Johnson Controls

Johnson Controls VP101DBB Bedienungsanleitung

Johnson Controls

Johnson Controls V46SA Series Bedienungsanleitung

Johnson Controls

Johnson Controls IOM3711 Bedienungsanleitung

Johnson Controls

Johnson Controls V43 Series Handbuch

Johnson Controls

Johnson Controls VG8000V Series Bedienungsanleitung

Johnson Controls

Johnson Controls Penn P28 Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls Mercury 3 Series Handbuch

Johnson Controls

Johnson Controls VP140 Bedienungsanleitung

Johnson Controls

Johnson Controls M300CJ Bedienungsanleitung

Johnson Controls

Johnson Controls 300 Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco RV-1A Bedienungsanleitung

Johnson Controls

Johnson Controls GS-20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls System 450 Series Bedienungs- und Wartungshandbuch

Johnson Controls

Johnson Controls S300 Series Montageanleitung

Johnson Controls

Johnson Controls Tyco 8200-1466-01 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung