Johnson Controls CKM-F8P Handbuch

24-10707-147 Revision C

December 2017

P2000

Security Management System

CKM-F8P

power distribution module

hardware

installation

Johnson Controls

No part of this document may be reproduced without the prior permission of Johnson Controls.

If this document is translated from the original English version by Johnson Controls, all reasonable

endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable

for any translation errors contained herein or for incidental or consequential damages in connection

with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking your equipment, keep all original manufacturer documentation for future

reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Acknowledgment

Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and

product names are trademarks or registered trademarks of their respective owners.

Declaration of Conformity

United States: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Canada: CAN ICES-3 (A)/NMB-3(A)

CKM-F8P Hardware Installation Manual

24-10707-147 Rev. C

CKM-F8P POWER DISTRIBUTION MODULE

This document provides hardware installation and setup instructions for the

CKM-F8P power distribution module. This document consists of the following

sections:

•General Information on page 1

•Mounting Information on page 3

•Wiring Information on page 4

•Specifications on page 7

GENERAL INFORMATION

The CKM-F8P power distribution module provides eight zones of fused or

PTC-protected power distribution with Fire Alarm Interface (FAI) control. The

CKM-F8P accepts one or two DC power inputs, either of which are available

on any output zone. Each output can be enabled for FAI, disabled for FAI, or set

for continuous output.

Figure 1: CKM-F8P Hardware

CKM-F8P Hardware Installation Manual

24-10707-147 Rev. C

Component Description

Component Names (Click on a link for full description)

FlexIO Connectors

B1 Connectors (J1 and J4)

B2 Connectors (J3 and J5)

Output Selection Jumpers (JP1 – JP8)

B2 LED (D4) – Green

B1 LED (D3) – Green

BR Connectors (J3 and J6)

Zone Outputs (Out1 – Out8)

FAI LED (D11) – Red

Optional Output Fuses (F1 – F8)

Component Description

FlexIO Connectors These connectors pass the FAI and Fault signals to and from the

CKM-F8P board and pass the FlexIO bus on to other accessory

boards in the system.

B1 Connectors (J1

and J4)

Faston connectors for the B1 voltage bus in the system.

The voltage on the B1 bus comes from the DC1 Faston connector

of a power supply. This voltage will be directed to any outputs

whose output selection jumper is set to one of the B1 positions.

B2 Connectors (J3

and J5)

Use these Faston connectors for the B2 voltage bus in the system.

The voltage on the B2 bus comes from the DC1 Faston connector

of the power supply. This voltage will be directed to any outputs

whose output selection jumper is set to the B2 position. If you are

using the CKM-F8P in a single voltage system, leave these Faston

connectors unused.

Output Selection

Jumpers (JP1 –

JP8)

Output selection jumpers select the voltage bus input for the output

and the FAI operation for the zone. Jumper numbers correspond

with the zone number (for example, JP1 is the jumper for OUT1).

Possible settings are as follows:

• Pos. 1 (Top) - Continuous output of B1 voltage

• Pos. 2 B1 - Enables voltage on FAI

• Pos. 3 B1 - Disables voltage on FAI

• Pos. 4 - Constant output of B2 voltage

• Pos. 5 B2 - Enables voltage on FAI

• Pos. 6 (Bot.) B2 - Disables voltage on FAI

• Removed - Disables output

B2 LED (D4) –

Green

The B2 LED lights when voltage is available on the B2 bus.

Note: This LED does not light in a single voltage system.

B1 LED

(D3) – Green

The B1 LED lights when voltage is available on the B1 bus.

CKM-F8P Hardware Installation Manual

24-10707-147 Rev. C

MOUNTING INFORMATION

Mount the CKM-F8P board to an enclosure using the four snap-in standoffs

supplied.

To mount the CKM-F8P board to an enclosure:

1. Locate the appropriate mounting holes in the enclosure and snap the

standoffs into the holes.

2. Align the board mounting holes with the standoffs and snap the board

onto the standoffs. Be sure the board is properly oriented.

Figure 2: Mounting the CKM-F8P Board to an Enclosure

BR Connectors

(J3 and J6)

The DC Common bus in the system. All boards in the system must

have their BR Faston connectors wired together for proper

operation (except for between the DC and AC sections of an FPX

hybrid system).

Zone Outputs

(Out1 – Out8)

These are zone output terminal strips are removable and accept

wire sizes from AWG14 to AWG22. The terminals are labeled on

the PC board underneath the terminal strip.

Any locking device shall be configured for fail safe operation upon

occurrence of an alarm.

FAI LED

(D11) – Red

The FAI LED lights when FAI is active and an FAI input signal is

received from the FPO power supply.

Optional Output

Fuses (F1 – F8)

When using the PTC version of the CKM-F8P, the fuse will be

replaced with a soldered-in PTC.

Component Description

CKM-F8P Hardware Installation Manual

24-10707-147 Rev. C

WIRING INFORMATION

This section covers the following:

•Connecting the CKM-F8P Power Distribution Module

•Dual Voltage using Two Power Supplies with Eight Zones of FAI

Controllable Distribution

•Specifications

Connecting the CKM-F8P Power Distribution Module

Each of the B1, B2, BR, and FlexIO buses has two connectors. You can

use these connectors interchangeably.

For example, FlexIO from the power supply may be connected to either

of the CKM-F8P’s FlexIO connectors, the Main DC voltage source may

connect to either B1 terminal, and so on.

Figure 3: Connecting the CKM-F8P Board

WARNING: Risk of Electric Shock.

Remove all AC and battery power from the system before adding

or replacing a CKM-F8P module. Contact with components

carrying hazardous voltage can cause electric shock and may

result in severe personal injury or death.

CKM-F8P Hardware Installation Manual

24-10707-147 Rev. C

Single Voltage with Eight Zones of FAI Controllable Distribution

In this application, each zone output of the CKM-F8P may be set to

provide 24 V of continuous output, 24 V enabled for FAI, or 24 V

disabled for FAI. Because this is a single voltage system, only jumper

positions 1-3 are valid. FAI control on the CKM-F8P is achieved by

opening the NC contact on the power supply’s FAI input.

Figure 4: CKM-F8P Wiring: Single Voltage, Eight Zones

CKM-F8P Hardware Installation Manual

24-10707-147 Rev. C

Dual Voltage using Two Power Supplies with Eight Zones of FAI

Controllable Distribution

In this application, each zone output of the CKM-F8P may be set to

provide 24 V of continuous output, enable on FAI, or disable on FAI. FAI

control on the CKM-F8P is achieved by opening the NC contact on the

power supply’s FAI input.

Figure 5: CKM-F8P Wiring: Dual Voltage, Eight Zones

Inhaltsverzeichnis

Andere Johnson Controls Steuereinheit Handbücher

Johnson Controls

Johnson Controls System 450 Series Bedienungsanleitung

Johnson Controls

Johnson Controls System 450 Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco CV-300B Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco RV-1A Bedienungsanleitung

Johnson Controls

Johnson Controls UL Listed GS-20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls GM 20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls VF Series Bedienungsanleitung

Johnson Controls

Johnson Controls A19ZBC Series Service-Handbuch

Johnson Controls

Johnson Controls GH-5000 Bedienungsanleitung

Johnson Controls

Johnson Controls System 450 Series Bedienungs- und Wartungshandbuch

Johnson Controls

Johnson Controls Y20EBD Series Service-Handbuch

Johnson Controls

Johnson Controls tyco AMD-1 Bedienungsanleitung

Johnson Controls

Johnson Controls GM 20 Series Bedienungsanleitung

Johnson Controls

Johnson Controls EM-3000 Series Bedienungsanleitung

Johnson Controls

Johnson Controls IOM3731 Bedienungsanleitung

Johnson Controls

Johnson Controls IOM3711 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN P70 Series Handbuch

Johnson Controls

Johnson Controls M300CJ Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls S1-TTSCC01 Bedienungsanleitung

Johnson Controls

Johnson Controls METASYS NU-XBN101-0 Bedienungsanleitung

Johnson Controls

Johnson Controls M4-XPM Bedienungsanleitung

Johnson Controls

Johnson Controls GS Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung