Johnson Controls Mercury P2000 CKM-MR16IN Handbuch

24-10707-74 Revision D

December 2017

P2000

Security Management System

CKM-MR16IN

authentic Mercury™ terminal module

hardware

installation

Johnson Controls

No part of this document may be reproduced without the prior permission of Johnson Controls.

If this document is translated from the original English version by Johnson Controls, all reasonable

endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable

for any translation errors contained herein or for incidental or consequential damages in connection

with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking your equipment, keep all original manufacturer documentation for reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Single Point of Contact by Region

Acknowledgments

Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and

product names are trademarks or registered trademarks of their respective owners.

European Single Point of Contact

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

NA/SA Single Point of Contact

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

APAC Single Point of Contact

JOHNSON CONTROLS

C/O CONTROLS PRODUCT

MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

Declarations of Conformity

United States: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Canada: CAN ICES-3 (A)/NMB-3(A)

European Union: This product complies with the requirements of the EMC Directive.

This equipment must not be modified for any reason and it must be installed as stated in the

Manufacturer’s instruction. If this shipment (or any part thereof) is supplied as second-hand

equipment, equipment for sale outside the European Economic Area or as spare parts for either a

single unit or system, it is not covered by the Directives.

UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET

The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary

Burglar Alarm Units and Systems, UL 294 for Access Control Systems Units and Underwriters

Laboratories of Canada ULC/ORD-C1076-86.

CKM-MR16IN

When installed at the site the following requirements must be met to comply with these standards.

1. The CKM-MR16IN shall be mounted in Listed Enclosures CKM-CE75-E2M, CKM-CE150-

E4M, and Listed Burglar Alarm and Access Control System Units SPF10000-1I00, SPF1I100-

1I00 or SPF1I300-1J00.

2. A CKM-MR16IN mounted in Listed Enclosures CKM-CE75-E2M, CKM-CE150-E4M, and

Listed Burglar Alarm and Access Control System Units SPF10000-1I00, SPF1I100-1I00 or

SPF1I300-1J00 shall be powered through the CKM-F8P power distribution module.

3. Transient protection devices that are installed must not be removed or defeated.

4. Do not connect equipment to an AC power source that is controlled by a switch.

5. Power for devices connected through relay/control output wiring must be provided by a UL

Listed power limited power source.

6. A 1.5Kohm/750ohm custom end-of-line resistance supervised circuit was investigated by

Underwriter Laboratories.

7. Encrypted communication has not investigated by Underwriters Laboratories.

8. Suitable for use with the model P2K-nnn-UL-x Security Management System, where n can be

any number 0 through 9 and where x can be any three letters A through Z.

9. UL 294 Performance Levels

Destructive Attack Level I

Endurance Level IV

Line Security Level I

Standby Power Level I

CKM-MR16IN Hardware Installation Manual

24-10707-74 Rev. D

CKM-MR16IN INPUT TERMINAL MODULE

This document provides hardware installation and setup instructions for

CKM-MR16IN, the authentic Mercury™ terminal module. This document is

divided into the following sections:

•General Information on page 1

•Mounting Information on page 2

•Wiring Information on page 2

•Setup Information on page 6

•Status LEDs on page 8

•Specifications on page 10

•Maintenance on page 11

GENERAL INFORMATION

The CKM-MR16IN terminal module provides a solution to the OEM system

integrator for sensor monitoring and output control. The CKM-MR16IN has 16

supervised inputs and 2 form-C contact relays for load switching. In addition, 2

digital inputs are used for cabinet tamper and power fault status monitoring.

The CKM-MR16IN requires 12 to 24 VDC for power.

CKM-MR16IN Hardware Installation Manual

24-10707-74 Rev. D

MOUNTING INFORMATION

Figure 1: CKM-MR16IN Hardware

WIRING INFORMATION

This sections covers the following:

•Cable Routing

•Supplying Power

•Communications Wiring

•CKM-MR16IN Communications Wiring.

•Relay Outputs Wiring

2.00 [50.80] 3.00 [76.20] 2.00 [50.80]

8.00 [203.20]

0.25 [6.35] 5.50 [139.70]

6.00 [152.40]

OUTPUTS

TB11

VIN

GND

TR-

R+

R-

GND

TR+

TB10

RS-485

TB1

TB2

TB3

TB4

TB9

GND

J6 J5

12345678

OUT 1

OUT 2

TB12

K1K2

TB5

I10

TB6

I11

I12

TB7

I13

I14

TB8

I15

I16

MR-16IN

RS-485 TERM

INPUT STATUS LEDs

INPUTS

DIP SWITCHES

STATUS LEDs

Ø0.16 [Ø3.96]

8 PLACES

INPUTS

SIO COMMUNICATION

PORT, RS-485

POWER IN

12-24Vdc

CKM-MR16IN Hardware Installation Manual

24-10707-74 Rev. D

Cable Routing

The cables should run in grounded conduit or at least two feet from AC

power, fluorescent lights, or other high energy sources.

IMPORTANT: All data cables should be physically separated from power lines. If

conduit is used, do not run data cables in the same conduit as power cables or

certain door strike cables, e.g. strike voltage greater that 42V or Magnetic door

locks without EMI suppression.

All cables must conform with the following regulations:

• National Electrical Code

•NFPA 70

• Local electrical codes

• Canadian Electric Code C22.1 (installations in Canada)

• BSI Standard BS7671, latest edition (installations in Great Britain)

Cabling should be made using good wiring practices and should be long

enough to allow service loops at their terminations in the enclosure.

Supplying Power

The CKM-MR16IN accepts 12 to 24 VDC for power. Locate power

source as close to the unit as possible. Connect power with minimum of

18 AWG wires.

IMPORTANT: Observe polarity on VIN.

Figure 2: CKM-MR16IN Supplying Power

12 TO 24Vdc

GND

VIN

TB11

CKM-MR16IN Hardware Installation Manual

24-10707-74 Rev. D

Communications Wiring

The CKM-MR16IN communicates to an intelligent controller (EP2500

for example) via a two-wire RS-485 interface. The interface allows

multidrop communication on a single bus of up to 4,000 feet (1,200 m).

Shielded cable of 24 AWG with characteristic impedance of 120 ohm is

specified for the RS-485 interface. The last devices on each end of the

cable should have the terminator installed (set jumper J1 on).

Install the following jumpers for the RS-485 interface according to the

selected configuration.

Figure 3: CKM-MR16IN Communications Wiring.

Alarm Inputs Wiring

Inputs 1 to 16 may be configured to use or not use End Of Line (EOL)

resistors and to use normally open or normally closed contacts. Input CT

and input BA are used for monitoring cabinet tamper and power failure,

respectively. These two inputs are for contact closure monitoring only,

and do not use EOL resistors. Input configuration is set via host software.

CKM-MR16IN Hardware Installation Manual

24-10707-74 Rev. D

Figure 4: Alarm Contact Wiring

Relay Outputs Wiring

Two form-C contact relays are provided for controlling door strikes or

other devices. Load switching can cause abnormal contact wear and

premature contact failure. Switching of inductive loads (strike) also

causes EMI (electromagnetic interference) which may interfere with

normal operation of other equipment. To minimize premature contact

failure and to increase system reliability, contact protection circuit must

be used. The following two circuits are recommended. Locate the

protection circuit as close to the load as possible, but within 12 inches

(30 cm), as the effectiveness of the circuit decreases if it is located further

away.

Figure 5: CKM-MR16IN Relay Outputs Wiring

1K,1%

TB6 TB5

I10

I11

I12

CKM-MR16IN Hardware Installation Manual

24-10707-74 Rev. D

SETUP INFORMATION

Use the Jumpers for RS-485 termination and two-wire/four-wire select.

Use the Jumpers to select the device address, communication baud rate, and to

enable or disable encrypted communication. All other configuration settings

are set via host software.

Table 1: Jumpers

Jumper Description

J1 RS-485 termination, install in first and last units only

J2 Factory Use Only

J3 Two-wire/four-wire select, install in 2W position only

J4 - J9 Factory Use Only

Table 2: Switches

S8 S7 S6 S5 S4 S3 S2 S1 Selection

OFF OFF OFF OFF OFF Address 0

OFF OFF OFF OFF ON Address 1

OFF OFF OFF ON OFF Address 2

OFF OFF OFF ON ON Address 3

OFF OFF ON OFF OFF Address 4

OFF OFF ON OFF ON Address 5

OFF OFF ON ON OFF Address 6

OFF OFF ON ON ON Address 7

OFF ON OFF OFF OFF Address 8

OFF ON OFF OFF ON Address 9

OFF ON OFF ON OFF Address 10

OFF ON OFF ON ON Address 11

OFF ON ON OFF OFF Address 12

OFF ON ON OFF ON Address 13

OFF ON ON ON OFF Address 14

OFF ON ON ON ON Address 15

ON OFF OFF OFF OFF Address 16

Inhaltsverzeichnis

Andere Johnson Controls Steuereinheit Handbücher

Johnson Controls

Johnson Controls CKM-MR51E Montageanleitung

Johnson Controls

Johnson Controls Digital Vision Network 5000 Series Kurzanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls MS-NCM4510-2 Bedienungsanleitung

Johnson Controls

Johnson Controls Penn P28 Series Bedienungsanleitung

Johnson Controls

Johnson Controls M300CJ Bedienungsanleitung

Johnson Controls

Johnson Controls VP140 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls GH-5000 Bedienungsanleitung

Johnson Controls

Johnson Controls MS-IOM3723 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco TJPX0500003 Bedienungsanleitung

Johnson Controls

Johnson Controls VF Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls VG8000V Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls S1-TTSCC Bedienungsanleitung

Johnson Controls

Johnson Controls V43 Series Handbuch

Johnson Controls

Johnson Controls TrueRH Series Leitfaden

Johnson Controls

Johnson Controls Tyco DV-5a Series Bedienungsanleitung

Johnson Controls

Johnson Controls S1-TTSCC01 Bedienungsanleitung

Johnson Controls

Johnson Controls TYCO DPV-1 Gebrauchsanweisung

Johnson Controls

Johnson Controls Autocall MX Indoor Isolated Callpoint Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco CV-300B Bedienungsanleitung

Johnson Controls

Johnson Controls MS-IOM2710-0U Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung